Center for Quantum Devices - Most Downloaded Journal Articles

Page 8 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

16.	Optoelectronic Integrated Circuits (OEICs) for Next Generation WDM Communications M. Razeghi and S. Slivken SPIE Conference, Boston, MA, -- July 29, 2002 ...[Visit Journal] This paper reviews some of the key enabling technologies for present and future optoelectronic intergrated circuits. This review concentrates mainly on technology for lasers, waveguides, modulators, and fast photodetectors as the basis for next generation communicatiosn systems. Emphasis is placed on intergrations of components and mass production of a generic intelligent tranciever. [reprint (PDF)]
16.	Electron-spin resonance of the two-dimensional electron gas in Ga0.47In0.53As-InP heterostructures M. Dobers, J. P. Vieren,, Y. Guldner P. Bove, F. Omnes, and M. Razeghi Phys. Rev. B 40, 8075(R) – Published 15 October, 1989-- October 15, 1989 ...[Visit Journal] The microwave-induced change of the magnetoresistivity of Ga0.47In0.53As-InP heterostructures reveals resonant structure which is attributed to electron-spin resonance of the two-dimensional conduction electrons. With microwave frequencies up to 480 GHz and in magnetic fields up to 12 T, we studied the spin splitting of the two lowest Landau levels in different samples. The spin splitting of these Landau levels is a quadratic function of the magnetic field and its extrapolation to zero magnetic field leads to vanishing spin splitting. The g factors depend on the magnetic field B and the Landau level N as follows: g(B,N)=𝑔0-c(N+1/2)B, where 𝑔0 and c are sample-dependent parameters, which are of the order of 𝑔0≊4.1 and c≊0.08 T−1, in the studied heterostructures. [reprint (PDF)]
16.	Fabrication of GaN nanotubular material using MOCVD with aluminum oxide membrane W.G. Jung, S.H. Jung, P. Kung, and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 61270K-- January 23, 2006 ...[Visit Journal] GaN nanotubular material is fabricated with aluminum oxide membrane in MOCVD. SEM, XRD, TEM and PL are employed to characterize the fabricated GaN nanotubular material. An aluminum oxide membrane with ordered nano holes is used as template. Gallium nitride is deposited at the inner wall of the nano holes in aluminum oxide template, and the nanotubular material with high aspect ratio is synthesized using the precursors of TMG and ammonia gas. Optimal synthesis condition in MOCVD is obtained successfully for the gallium nitride nanotubular material in this research. The diameter of GaN nanotube fabricated is approximately 200 ~ 250 nm and the wall thickness is about 40 ~ 50 nm. GaN nanotubular material consists of numerous fine GaN particulates with sizes ranging 15 to 30 nm. [reprint (PDF)]
16.	High-power, continuous-wave, phase-locked quantum cascade laser arrays emitting at 8 μm WENJIA ZHOU,QUAN-YONG LU,DONG-HAI WU, STEVEN SLIVKEN, AND MANIJEH RAZEGHI OPTICS EXPRESS 27, 15776-15785-- May 20, 2019 ...[Visit Journal] We report a room-temperature eight-element phase-locked quantum cascade laser array emitting at 8 μm with a high continuous-wave power of 8.2 W and wall plug efficiency of 9.5%. The laser array operates primarily via the in-phase supermode and has single-mode emission with a side-mode suppression ratio of ~20 dB. The quantum cascade laser active region is based on a high differential gain (8.7 cm/kA) and low voltage defect (90 meV) design. A record high wall plug efficiency of 20.4% is achieved from a low loss buried ridge type single-element Fabry-Perot laser operating in pulsed mode at 20 °C. [reprint (PDF)]
16.	Growth of Ga0.47In0.53As‐InP quantum wells by low pressure metalorganic chemical vapor deposition M. Razeghi; J. P. Hirtz; U. O. Ziemelis; C. Delalande; B. Etienne; M. Voos Appl. Phys. Lett. 43, 585–587 (1983)-- September 15, 1983 ...[Visit Journal] We describe the growth of multiquantum well and single quantum well Ga0 ,47 InOS3 As-InP structures by low pressure metalorganic chemical vapor deposition. The multi well structure consists of 2S-, SO-, 100-, and 200-A quantum wells (Ga0 ,47 InOS3 As layers) separated by SOO-A barriers (InP layers). Auger measurements indicate the presence offour distinct wells with abrupt boundaries. Photoluminescence measurements are consistent with the existence of four wells; however, deviations are noted between experimentally determined and theoretically predicted recombination energies. An analogous situation exists for the single (SO and 100 A) quantum well structures. Possible explanations, including variation of well composition, variation of well thickness, and participation of impurities in the recombination process are suggested. [reprint (PDF)]
16.	The effect of doping the M-barrier in very long-wave type-II InAs/GaSb heterodiodes D. Hoffman, B.M. Nguyen, E.K. Huang, P.Y. Delaunay, M. Razeghi, M.Z. Tidrow and J. Pellegrino Applied Physics Letters, Vol. 93, No. 3, p. 031107-1-- July 21, 2008 ...[Visit Journal] A variation on the standard homo-diode Type-II superlattice with an M-barrier between the pi-region and the n-region is shown to suppress the dark currents. By determining the optimal doping level of the M-superlattice, dark current densities of 4.95 mA·cm^-2 and quantum efficiencies in excess of 20% have been demonstrated at the moderate reverse bias of 50 mV; allowing for near background-limited performance with a Johnson-noise detectivity of 3.11×10¹⁰ Jones at 77 K for a 14.58 µm cutoff wavelength for large area diodes without passivation. This is comparable to values for the state-of-the-art HgCdTe photodiodes. [reprint (PDF)]
16.	*A Crystallographic Model of (001) Aluminum Nitride Epitaxial Thin Film Growth on (001) Sapphire Substrate* C.J. Sun, P. Kung, A. Saxler, H. Ohsato, M. Razeghi, and K. Haritos Journal of Applied Physics 75 (8)-- April 15, 1994 ...[Visit Journal] A direct comparison of the physical properties of GaN thin films is made as a function of the choice of substrate orientations. Gallium nitride single crystals were grown on (0001) and (011-bar 2) sapphire substrates by metalorganic chemical vapor deposition. Better crystallinity with fine ridgelike facets is obtained on the (011-bar 2) sapphire. Also lower carrier concentration and higher mobilities indicate both lower nitrogen vacancies and less oxygen incorporation on the (011-bar 2) sapphire. The results of this study show better physical properties of GaN thin films achieved on (011-bar 2) sapphire. [reprint (PDF)]
16.	High power frequency comb based on mid-infrared quantum cascade laser at λ ~9μm Q. Y. Lu, M. Razeghi, S. Slivken, N. Bandyopadhyay, Y. Bai, W. J. Zhou, M. Chen, D. Heydari, A. Haddadi, R. McClintock, M. Amanti, and C. Sirtori Appl. Phys. Lett. 106, 051105-- February 2, 2015 ...[Visit Journal] We investigate a frequency comb source based on a mid-infrared quantum cascade laser at λ ∼9 μm with high power output. A broad flat-top gain with near-zero group velocity dispersion has been engineered using a dual-core active region structure. This favors the locking of the dispersed Fabry-Pérot modes into equally spaced frequency lines via four wave mixing. A current range with a narrow intermode beating linewidth of 3 kHz is identified with a fast detector and spectrum analyzer. This range corresponds to a broad spectral coverage of 65 cm⁻¹ and a high power output of 180 mW for ∼176 comb modes. [reprint (PDF)]
16.	Reliability of Aluminum-Free 808 nm High-Power Laser Diodes with Uncoated Mirrors I. Eliashevich, J. Diaz, H. Yi, L. Wang, and M. Razeghi Applied Physics Letters 66 (23)-- June 5, 1995 ...[Visit Journal] The reliability of uncoated InGaAsP/GaAs high‐power diode lasers emitting at 808 nm wavelength has been studied. 47 W of quasicontinuous wave output power (pulse width 200 μs, frequency 20 Hz) have been obtained from a 1 cm wide laser bar. A single‐stripe diode without mirror coating has been life tested at 40 °C for emitting power of 800 mW continuous wave (cw) and showed no noticeable degradation and no change of the lasing wavelength after 6000 h of operation. [reprint (PDF)]
16.	Highly selective two-color mid-wave and long-wave infrared detector hybrid based on Type-II superlattices E.K. Huang, M.A. Hoang, G. Chen, S.R. Darvish, A. Haddadi, and M. Razeghi Optics Letters, Vol. 37, No. 22, p. 4744-4746-- November 15, 2012 ...[Visit Journal] We report a two-color mid-wave infrared (MWIR) and long-wave infrared (LWIR) co-located detector with 3 μm active region thickness per channel that is highly selective and can perform under high operating temperatures for the MWIR band. Under back-side illumination, a temperature evolution study of the MWIR detector’s electro-optical performance found the 300 K background-limit with 2π field-of-view to be achieved below operating temperatures of 160 K, at which the temperature’s 50% cutoff wavelength was 5.2 μm. The measured current reached the system limit of 0.1 pA at 110 K for 30 μm pixel-sized diodes. At 77 K, where the LWIR channel operated with a 50% cutoff wavelength at 11.2 μm, an LWIR selectivity of ∼17% was achieved in the MWIR wave band between 3 and 4.7 μm, making the detector highly selective. [reprint (PDF)]
16.	Self-Detecting Mid-Infrared Dual-Comb Spectroscopy Based on High-Speed Injection-Locked Quantum Cascade Lasers Yu Ma, Dapeng Wu, Ruixin Huang, Shichen Zhang, Binru Zhou, Zejun Ma, Yongqiang Sun, Junqi Liu, Ning Zhuo, Jinchuan Zhang, Shenqiang Zhai, Shuman Liu, Fengqi Liu, Manijeh Razeghi, and Quanyong Lu Adv. Photonics Res. 2500062 (2025) ...[Visit Journal] Dual-comb spectrometer based on quantum cascade lasers (QCLs) is gaining fast development and revolutionizing the precision measurement with high-frequency and temporal resolutions. In these measurements, high-bandwidth photodetectors are normally used for signal acquisition and processing, which complicates the measurement system. QCL is well-known for its picosecond gain-recovery time with an intrinsic bandwidth of tens of GHz. In this work, a compact self-detecting dual-comb spectroscopy (DCS) is demonstrated based on dispersion-engineered, high-speed packaged QCLs under coherent injection locking. The laser source is designed and fabricated into a hybrid-monolithic-integrated waveguide and epi-down packaged on a wideband-designed submount to fully explore the high-speed feature up to fourth-order harmonic state with a cutoff frequency of 40 GHz. The effective radio frequency (RF) injection locking diminishes the issue of optical feedback and enables high-bandwidth self-detection based on QCLs. Clear and stable multiheterodyne signal corresponding to a spectral range of 68 cm−1 and narrow comb tooth linewidth of ≈10 kHz is observed without using external detector or numerical process. The demonstrated broadband, high-power, self-detecting mid-infrared QCL DCS has a great potential for future applications of molecular sensing and spectroscopy. [reprint (PDF)]
16.	Electroluminescence of InAs/GaSb heterodiodes D. Hoffman, A. Hood, E. Michel, F. Fuchs, and M. Razeghi IEEE Journal of Quantum Electronics, 42 (2)-- February 1, 2006 ...[Visit Journal] The electroluminescence of a Type-II InAs-GaSb superlattice heterodiode has been studied as a function of injection current and temperature in the spectral range between 3 and 13 μm. The heterodiode comprises a Be-doped midwavelength infrared (MWIR) superlattice with an effective bandgap around 270 meV and an undoped long wavelength infrared (LWIR) superlattice with an effective bandgap of 115 meV. [reprint (PDF)]
16.	High performance InGaAs/InGaP quantum dot infrared photodetector achieved through doping level optimization S. Tsao, K. Mi, J. Szafraniec, W. Zhang, H. Lim, B. Movaghar, and M. Razeghi SPIE Conference, Jose, CA, Vol. 5732, pp. 334-- January 22, 2005 ...[Visit Journal] We report an InGaAs/InGaP/GaAs quantum dot infrared photodetector grown by metalorganic chemical vapor deposition with detectivity of 1.3x10¹¹ cm·Hz^½/W at 77K and 1.2x10¹⁰ ccm·Hz^½/W at 120K. Modeling of the Quantum dot energy levels showed us that increased photoresponse could be obtained by doping the quantum dots to 4 electrons per dot instead of the usual 2 electrons per dot. This happens because the primary photocurrent transition is from the first excited state to a higher excited state. Increasing the quantum doping in our device yielded significant responsivity improvement and much higher detectivity as a result. This paper discusses the performance of this higher doping device and compares it to our previously reported device with lower doping. [reprint (PDF)]
16.	Very high quantum efficiency in type-II InAs/GaSb superlattice photodiode with cutoff of 12 µm B.M. Nguyen, D. Hoffman, Y. Wei, P.Y. Delaunay, A. Hood and M. Razeghi Applied Physics Letters, Vol. 90, No. 23, p. 231108-1-- June 4, 2007 ...[Visit Journal] The authors report the dependence of the quantum efficiency on device thickness of Type-II InAs/GaSb superlattice photodetectors with a cutoff wavelength around 12 µm. The quantum efficiency and responsivity show a clear delineation in comparison to the device thickness. An external single-pass quantum efficiency of 54% is obtained for a 12 µm cutoff wavelength photodiodes with a -region thickness of 6.0 µm. The R₀A value is kept stable for the range of structure thicknesses allowing for a specific detectivity (2.2×10¹¹ cm·Hz^½/W). [reprint (PDF)]
16.	Effect of sidewall surface recombination on the quantum efficiency in a Y₂O₃ passivated gated type-II InAs/GaSb long-infrared photodetector array G. Chen, A. M. Hoang, S. Bogdanov, A. Haddadi, S. R. Darvish, and M. Razeghi Appl. Phys. Lett. 103, 223501 (2013)-- November 25, 2013 ...[Visit Journal] Y₂O₃ was applied to passivate a long-wavelength infrared type-II superlattice gated photodetector array with 50% cut-off wavelength at 11 μm, resulting in a saturated gate bias that was 3 times lower than in a SiO₂ passivated array. Besides effectively suppressing surface leakage, gating technique exhibited its ability to enhance the quantum efficiency of 100 × 100 μm size mesa from 51% to 57% by suppressing sidewall surface recombination. At 77 K, the gated photodetector showed dark current density and resistance-area product at −300 mV of 2.5 × 10⁻⁵ A/cm² and 1.3 × 10⁴ Ω·cm², respectively, and a specific detectivity of 1.4 × 10¹² Jones. [reprint (PDF)]
16.	Demonstration of high performance bias-selectable dual-band short-/mid-wavelength infrared photodetectors based on type-II InAs/GaSb/AlSb superlattices A.M. Hoang, G. Chen, A. Haddadi and M. Razeghi Applied Physics Letters, Vol. 102, No. 1, p. 011108-1-- January 7, 2013 ...[Visit Journal] High performance bias-selectable dual-band short-/mid-wavelength infrared photodetector based on InAs/GaSb/AlSb type-II superlattice with designed cut-off wavelengths of 2 μm and 4 μm was demonstrated. At 150 K, the short-wave channel exhibited a quantum efficiency of 55%, a dark current density of 1.0 × 10⁻⁹ A/cm² at −50 mV bias voltage, providing an associated shot noise detectivity of 3.0 × 10¹³ Jones. The mid-wavelength channel exhibited a quantum efficiency of 33% and a dark current density of 2.6 × 10⁻⁵ A/cm² at 300 mV bias voltage, resulting in a detectivity of 4.0 × 10¹¹ Jones. The spectral cross-talk between the two channels was also discussed for further optimization. [reprint (PDF)]
16.	First Demonstration of ~ 10 microns FPAs in InAs/GaSb SLS M. Razeghi, P.Y. Delaunay, B.M. Nguyen, A. Hood, D. Hoffman, R. McClintock, Y. Wei, E. Michel, V. Nathan and M. Tidrow IEEE LEOS Newsletter 20 (5)-- October 1, 2006 ...[Visit Journal] The concept of Type-II InAs/GaSb superlattice was first brought by Nobel Laureate L. Esaki, et al. in the 1970s. There had been few studies on this material system until two decades later when reasonable quality material growth was made possible using molecular beam epitaxy. With the addition of cracker cells for the group V sources and optimizations of material growth conditions, the superlattice quality become significantly improved and the detectors made of these superlattice materials can meet the demand in some practical field applications. Especially in the LWIR regime, it provides a very promising alternative to HgCdTe for better material stability and uniformity, etc. We have developed the empirical tight binding model (ETBM) for precise determination of the superlattice bandgap. [reprint (PDF)]
16.	On the performance and surface passivation of type-II InAs/GaSb superlattice photodiodes for the very-long- wavelength infrared A. Hood, M. Razeghi, E. Aifer, G.J. Brown Applied Physics Letters 87 (1)-- October 10, 2005 ...[Visit Journal] We demonstrate very-long-wavelength infrared Type-II InAs/GaSb superlattice photodiodes with a cutoff wavelength (λ_c,50%) of 17 μm. We observed a zero-bias, peak Johnson noise-limited detectivity of 7.63×10⁹ cm·Hz^½/W at 77 K with a 90%-10% cutoff width of 17 meV, and quantum efficiency of 30%. Variable area diode zero-bias resistance-area product (R₀A) measurements indicated that silicon dioxide passivation increased surface resistivity by nearly a factor of 5, over unpassivated photodiodes, and increased overall R₀A uniformity. The bulk R₀A at 77 K was found to be 0.08 Ω·cm², with RA increasing more than twofold at 25 mV reverse bias. [reprint (PDF)]
16.	Continuous wave, room temperature operation of λ ~ 3μm quantum cascade laser N. Bandyopadhyay, Y. Bai, S. Tsao, S. Nida, S. Slivken and M. Razeghi SPIE Proceedings, Vol. 8631, p. 86310M-1, Photonics West, San Francisco, CA-- February 3, 2013 ...[Visit Journal] Quantum Cascade Lasers (QCLs), operating in continuous wave (CW) at room temperature(RT) in 3-3.5 μm spectral range, which overlaps the spectral fingerprint region of many hydrocarbons, is essential in spectroscopic trace gas detection, environment monitoring, and pollution control. A 3 μm QCL, operating in CW at RT is demonstrated. This initial result makes it possible, for the most popular material system (AlInAs/GaInAs on InP) used in QCLs in mid-infrared and long-infrared, to cover the entire spectral range of mid-infrared atmospheric window (3-5 μm). In_0.79Ga_0.21As/In_0.11Al_0.89As strain balanced superlattice, which has a large conduction band offset, was grown. The strain was balanced with composite barriers (In_0.11Al_0.89As /In_0.4Al_0.6As) in the injector region, to eliminate the need of extremely high compressively strained GaInAs, whose pseudomorphic growth is very difficult. [reprint (PDF)]
16.	Very Long Wavelength Infrared Type-II Detectors Operating at 80K H. Mohseni, A. Tahraoui, J. Wojkowski, M. Razeghi, G.J. Brown, W.C. Mitchel, and Y.S. Park Applied Physics Letters 77 (11)-- September 11, 2000 ...[Visit Journal] We report a demonstration of very long wavelength infrared detectors based on InAs/GaSb superlattices operating at T = 80 K. Detector structures with excellent material quality were grown on an optimized GaSb buffer layer on GaAs semi-insulating substrates. Photoconductive devices with 50% cutoff wavelength of λ_c = 17 μm showed a peak responsivity of about 100 mA/W at T = 80 K. Devices with 50% cutoff wavelengths up to λ_c = 22 μm were demonstrated at this temperature. Good uniformity was obtained over large areas even for the devices with very long cutoff wavelengths. [reprint (PDF)]
16.	High Quality Aluminum Nitride Epitaxial Layers Grown on Sapphire Substrates A. Saxler, P. Kung, C.J. Sun, E. Bigan and M. Razeghi Applied Physics Letters 64 (3)-- January 17, 1994 ...[Visit Journal] In this letter we report the growth of high quality AlN epitaxial layers on sapphire substrates. The AlN grown on (00·1) sapphire exhibited a better crystalline quality than that grown on (01·2) sapphire. An x-ray rocking curve of AlN on (00·1) Al₂O₃ yielded a full width at half-maximum of 97.2 arcsec, which is the narrowest value reported to our knowledge. The AlN peak on (01·2) Al₂O₃ was about 30 times wider. The absorption edge measured by ultraviolet transmission spectroscopy for AlN grown on (00·1) Al₂O₃ was about 197 nm. [reprint (PDF)]
16.	Comparison of ZnO nanostructures grown using pulsed laser deposition, metal organic chemical vapor deposition, and physical vapor transport V.E. Sandana, D.J. Rogers, F. Hosseini Teherani, R. McClintock, C. Bayram, M. Razeghi, H-J Drouhin, M.C. Clochard, V. Sallett, G. Garry, and F. Falyouni Journal of Vacuum Science and Technology B, Vol. 27, No. 3, May/June, p. 1678-1683-- May 29, 2009 ...[Visit Journal] This article compares the forms and properties of ZnO nanostructures grown on Si (111) and c-plane sapphire (c-Al₂O₃) substrates using three different growth processes: metal organic chemical vapor deposition (MOCVD), pulsed laser deposition (PLD), and physical vapor transport (PVT). A very wide range of ZnO nanostructures was observed, including nanorods, nanoneedles, nanocombs, and some novel structures resembelling “bevelled” nanowires. PVT gave the widest family of nanostructures. PLD gave dense regular arrays of nanorods with a preferred orientation perpendicular to the substrate plane on both Si and c-Al₂O₃ substrates, without the use of a catalyst. X-ray diffraction (XRD) studies confirmed that nanostructures grown by PLD were better crystallized and more highly oriented than those grown by PVT and MOCVD. Samples grown on Si showed relatively poor XRD response but lower wavelength emission and narrower linewidths in PL studies. [reprint (PDF)]
16.	Aluminum-free Quantum Well Intersubband Photodetectors with p-type GaAs Wells and lattice-matched ternary and quaternary barriers J. Hoff, E. Bigan, G.J. Brown, and M. Razeghi Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995 ...[Visit Journal] Acceptor doped Quantum Well Intersubband Photodetectors with GaAs wells and lattice matched barriers of both ternary (In_0.49Ga_0.51P) and quaternary (In_0.62Ga_0.38As_0.22P_0.78) materials have been grown on semi-insulating GaAs substrates by Low Pressure Metal Organic Chemical Vapor Deposition. Mesa devices were fabricated and subjected to a series of tests to illuminate experimentally some of the detection capabilities of the lattice matched quaternary InxGa1-xAsyP1-y system with (0 ≤ x ≤ 0.52) and (0 ≤ y ≤ 1). The observed photoresponse cut-off wavelengths are in good agreement with the activation energies observed in the temperature dependence of the dark currents. Kronig-Penney calculations were used to model the intersubband transition energies. [reprint (PDF)]
16.	Background limited performance of long wavelength infrared focal plane arrays fabricated from M-structure InAs/GaSb superlattices P.Y. Delaunay, B.M. Nguyen, D. Hoffman, E.K. Huang, P. Manurkar, S. Bogdanov and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-0W-- January 26, 2009 ...[Visit Journal] Recent advances in the design and fabrication of Type-II InAs/GaSb superlattices allowed the realization of high performance long wavelength infrared focal plane arrays. The introduction of an Mstructure barrier between the n-type contact and the pi active region reduced the tunneling component of the dark current. The M-structure design improved the noise performance and the dynamic range of FPAs at low temperatures. At 81K, the NEDT of the focal plane array was 23 mK. The noise of the camera was dominated by the noise component due to the read out integrated circuit. At 8 µm, the median quantum efficiency of the detectors was 71%, mainly limited by the reflections on the backside of the array. [reprint (PDF)]
16.	High-brightness LWIR quantum cascade lasers F. Wang, S. Slivken, and M. Razeghi F. Wang, S. Slivken, and M. Razeghi, High-brightness LWIR quantum cascade lasers, Optics Letters, vol. 46, No. 20, 5193 ...[Visit Journal] Long-wave infrared (LWIR, lambda~8-12 um) quantum cascade lasers (QCLs) are drawing increasing interest, as they provide the possibility of long-distance transmission of light through the atmosphere owing to the reduced water absorption. However, their development has been lagging behind the shorter wavelength QCLs due to much bigger technological challenges. In this Letter, through band structure engineering based on a highly localized diagonal laser transition strategy and out-coupler design using an electrically isolated taper structure, we demonstrate high beam quality single-mode LWIR QCLs with high-brightness (2.0 MW cm^-2 sr^-1 for lambda~10 um, 2.2 MW cm^-2 sr^-1 for lambda~9 um, 5.0 MW cm^-2 sr^-1 for lambda~8 um) light extraction from a single facet in continuous-wave operation at 15 ^oC. These results mark an important milestone in exploring the lighting capability of inter-sub-band semiconductor lasers in the LWIR spectral range. [reprint (PDF)]

Page 8 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)