Center for Quantum Devices - Most Downloaded Journal Articles

Page 6 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

17.	Optical and crystallographic properties and impurity incorporation of GaxIn1−xAs grown by liquid phase epitaxy, vapor phase epitaxy, and metal organic chemical vapor deposition K.‐H. Goetz; D. Bimberg; H. Jürgensen; J. Selders; A. V. Solomonov; G. F. Glinskii; M. Razeghi J. Appl. Phys. 54 (8): 4543–4552 (1983)-- March 29, 1983 ...[Visit Journal] Optical, crystallographic, and transport properties of nominally undoped n‐type and Zn doped p‐type Gax In1−xAs /InP (0.44 [reprint (PDF)]
17.	High-quality MOCVD-grown heteroepitaxial gallium oxide growth on III-nitrides enabled by AlOx interlayer Junhee Lee, Lakshay Gautam, and Manijeh Razeghi Junhee Lee, Manijeh RazeghiAppl. Phys. Lett. 123, 151902 (2023) https://doi.org/10.1063/5.0170383 ...[Visit Journal] We report high-quality Ga2O3 grown on an AlGaN/AlN/Sapphire in a single growth run in the same Metal Organic Chemical Vapor Deposition reactor with an AlOx interlayer at the Ga2O3/AlGaN interface. AlOx interlayer was found to enable the growth of single crystalline Ga2O3 on AlGaN in spite of the high lattice mismatch between the two material systems. The resulting nitride/oxide heterogenous heterostructures showed superior material qualities, which were characterized by structural, electrical, and optical characterization techniques. In particular, a significant enhancement of the electron mobility of the nitride/oxide heterogenous heterostructure is reported when compared to the individual electron mobilities of the Ga2O3 epilayer on the sapphire substrate and the AlGaN/AlN heterostructure on the sapphire substrate. This enhanced mobility marks a significant step in realizing the next generation of power electronic devices and transistors. [reprint (PDF)]
17.	Room temperature operation of Ge/SixGe1−x−ySny terahertz quantum cascade lasers predicted using extended combined resonant tunneling and rate equation model Zhou Li,, Zhichao Chen, Baiqi Zhang, Qiyun Lai, Zhanfeng Jiang, Yaoyao Liang Yulong Fan, Haoxiang Li, Qi Qin, Manijeh Razeghi∗, and Feihu Wang∗ J Appl Phys 138 (23) (2025) ...[Visit Journal] Raising operation temperature of terahertz (THz) quantum cascade lasers (QCLs) to room temperature remains a key challenge in QCL community. Group-IV semiconductors are believed to be a promising solution to this problem since the polar phonon–electron scattering is negligible at elevated temperature. Here, we develop a theoretical model for THz QCL development. This model is established on the combined resonant tunneling and rate equation framework and is extended to be applicable for group-IV QCL design through introducing new scattering mechanisms and continuum states carrier leakage. A two-well THz QCL based on a direct phonon extraction strategy is designed and predicted to be capable of working above 300 K. This result lays the foundation for future room temperature THz QCL devices development using group-IV semiconductors. [reprint (PDF)]
17.	Gain and recombination dynamics of quantum-dot infrared photodetectors H. Lim, B. Movaghar, S. Tsao, M. Taguchi, W. Zhang, A.A. Quivy, and M. Razeghi Physical Review B, 74 (20)-- November 15, 2006 ...[Visit Journal] In this paper we present a theory of diffusion and recombination in QDIPs which is an attempt to explain the recently reported values of gain in these devices. We allow the kinetics to encompass both the diffusion and capture rate limited regimes of carrier relaxation using rigorous random walk and diffusion methods. The photoconductive gains are calculated and compared with the experimental values obtained from InGaAs/InGaP/GaAs and InAs/InP QDIPs using the generation-recombination noise analysis. [reprint (PDF)]
17.	Widely tunable room temperature semiconductor terahertz source Q. Y. Lu, S. Slivken, N. Bandyopadhyay, Y. Bai, and M. Razeghi Appl. Phys. Lett. 105, 201102-- November 17, 2014 ...[Visit Journal] We present a widely tunable, monolithic terahertz source based on intracavity difference frequency generation within a mid-infrared quantum cascade laser at room temperature. A three-section ridge waveguide laser design with two sampled grating sections and a distributed-Bragg section is used to achieve the terahertz (THz) frequency tuning. Room temperature single mode THz emission with a wide tunable frequency range of 2.6–4.2 THz (∼47% of the central frequency) and THz power up to 0.1 mW is demonstrated, making such device an ideal candidate for THz spectroscopy and sensing. [reprint (PDF)]
17.	High-power mid- and far- wavelength infrared lasers for free space communication M. Razeghi; A. Evans; J. Nguyen; Y. Bai; S. Slivken; S.R. Darvish; K. Mi Proc. SPIE 6593, Photonic Materials, Devices, and Applications II, 65931V (June 12, 2007)-- June 12, 2007 ...[Visit Journal] Laser-based free-space communications have been developed to serve specific roles in "last mile" high-speed data networks due to their high security, low cost, portability, and high bandwidth. Conventional free-space systems based on near infrared optical devices suffer from reliability problems due to atmospheric scattering losses and scintillation effects, such as those encountered with storms, dust, and fog. Mid-infrared wavelengths are less affected by atmospheric effects and can significantly enhance link up-time and range. This paper will discuss some of the recent advances in high-power, high temperature, high reliability mid-infrared Quantum Cascade Lasers and their potential application in highly reliable free space communication links. [reprint (PDF)]
17.	Demonstration of InAsSb/AlInSb Double Heterostructure Detectors for Room Temperature Operation in the 5–8 μm Wavelength Range J.S. Wojkowski, H. Mohseni, J.D. Kim, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] We report the first demonstration of InAsSb/AlInSb double heterostructure detectors for room temperature operation. The structures were grown in a solid source molecular beam epitaxy reactor on semi-insulating GaAs substrate. The material was processed to 400x400 micrometer mesas using standard photolithography, etching, and metallization techniques. No optical immersion or surface passivation was used. The photovoltaic detectors showed a cutoff wavelength at 8 micrometer at 300 K. The devices showed a high quantum efficiency of 40% at 7 μm at room temperature. A responsivity of 300 mA/W was measured at 7 μm under a reverse bias of 0.25 V at 300 K resulting in a Johnson noise limited detectivity of 2x10⁸ cm·Hz^½/W. [reprint (PDF)]
17.	Future of Al_xGa_1-xN Materials and Device Technology for Ultraviolet Photodetectors P. Kung, A. Yasan, R. McClintock, S. Darvish, K. Mi, and M. Razeghi SPIE Conference, San Jose, CA, Vol. 4650, pp. 199-- May 1, 2002 ...[Visit Journal] Design of the photodetector structure is one of the key issues in obtaining high performance devices; especially the thickness of the intrinsic region for p-i-n photodiodes is a crucial value and needs to be optimized. We compare the performance of the p-i-n photodiodes with different widths for the depletion region, which shows a trade-off between speed and responsivity of the devices. [reprint (PDF)]
17.	SOLID-STATE DEEP UV EMITTERS/DETECTORS: Zinc oxide moves further into the ultraviolet David J. Rogers; Philippe Bove; Eric V. Sandana; Ferechteh Hosseini Teherani; Ryan McClintock; Manijeh Razeghi Laser Focus World. 2013;49(10):33-36.-- October 10, 2013 ...[Visit Journal] Latest advancements in the alloying of zinc oxide (ZnO) with magnesium (Mg) can offer an alternative to (Al) GaN-based emitters/detectors in the deep UV with reduced lattice and efficiency issues. The emerging potential of ZnO for UV emitter and detector applications is the result of a long, concerted, and fruitful R&D effort that has led to more than 7000 publications in 2012. ZnO is considered to be a potentially superior material for use in LEDs and laser diodes due to its larger exciton binding energy, as compared with 21 meV for GaN. Wet etching is also possible for ZnO with nearly all dilute acids and alkalis, while GaN requires hydrofluoric (HF) acid or plasma etching. High-quality ZnO films can be grown more readily on mismatched substrates and bulk ZnO substrates have better availability than their GaN equivalents. [reprint (PDF)]
17.	Passivation of Type-II InAs/GaSb superlattice photodetectors A. Hood, Y. Wei, A. Gin, M. Razeghi, M. Tidrow, and V. Nathan SPIE Conference, Jose, CA, Vol. 5732, pp. 316-- January 22, 2005 ...[Visit Journal] Leakage currents limit the operation of high performance Type-II InAs/GaSb superlattice photodiode technology. Surface leakage current becomes a dominant limiting factor, especially at the scale of a focal plane array pixel (< 25 µm) and must be addressed. A reduction of the surface state density, unpinning the Fermi level at the surface, and appropriate termination of the semiconductor crystal are all aims of effective passivation. Recent work in the passivation of Type-II InAs\GaSb superlattice photodetectors with aqueous sulfur-based solutions has resulted in increased R₀A products and reduced dark current densities by reducing the surface trap density. Additionally, photoluminescence of similarly passivated Type-II InAs/GaSb superlattice and InAs GaSb bulk material will be discussed. [reprint (PDF)]
17.	Uncooled operation of Type-II InAs/GaSb superlattice photodiodes in the mid- wavelength infrared range Y. Wei, A. Hood, H. Yau, A. Gin, M. Razeghi, M.Z. Tidrow, V. Natha Applied Physics Letters, 86 (23)-- June 6, 2005 ...[Visit Journal] We report high performance uncooled midwavelength infrared photodiodes based on interface-engineered InAs/GaSb superlattice. Two distinct superlattices were designed with a cutoff wavelength around 5 µm for room temperature and 77 K. The device quantum efficiency reached more than 25% with responsivity around 1 A/W. Detectivity was measured around 10⁹ cm·Hz^½/W at room temperature and 1.5×10¹³ cm·Hz^½/W at 77 K under zero bias. The devices were without antireflective coating. The device quantum efficiency stays at nearly the same level within this temperature range. Additionally, Wannier–Stark oscillations in the Zener tunneling current were observed up to room temperature. [reprint (PDF)]
17.	Short Wavelength Solar-Blind Detectors: Status, Prospects, and Markets M. Razeghi IEEE Proceedings, Wide Bandgap Semiconductor Devices: The Third Generation Semiconductor Comes of Age 90 (6)-- June 1, 2002 ...[Visit Journal] Recent advances in the research work on III-nitride semiconductors and Al_xGa_1-xN materials in particular has renewed the interest and led to significant progress in the development of ultraviolet (UV) photodetectors able to detect light in the mid- and near-UV spectral region (λ∼200-400 nm). There have been a growing number of applications which require the use of such sensors and, in many of these, it is important to be able to sense UV light without detecting infrared or visible light, especially from the Sun, in order to minimize the chances of false detection or high background. The research work on short-wavelength UV detectors has, therefore, been recently focused on realizing short-wavelength "solar-blind" detectors which, by definition, are insensitive to photons with wavelengths longer than ∼285 nm. In this paper the development of Al_xGa_1-xN-based solar-blind UV detectors will be reviewed. The technological issues pertaining to material synthesis and device fabrication will be discussed. The current state-of-the-art and future prospects for these detectors will be reviewed and discussed. [reprint (PDF)]
17.	Multi-band SWIR-MWIR-LWIR Type-II superlattice based infrared photodetector Manijeh Razeghi, Arash Dehzangi, Jiakai Li Results in Optics Volume 2, January 2021, 100054 https://doi.org/10.1016/j.rio.2021.100054 ...[Visit Journal] Type-II InAs/GaSb superlattices (T2SLs) has drawn a lot of attention since it was introduced in 1970, especially for infrared detection as a system of multi-interacting quantum wells. In recent years, T2SL material system has experienced incredible improvements in material quality, device structure designs and device fabrication process, which elevated the performances of T2SL-based photo-detectors to a comparable level to the state-of-the-art material systems for infrared detection such as Mercury Cadmium Telluride (MCT). As a pioneer in the field, center for quantum devices (CQD) has been involved in growth, design, characterization, and introduction of T2SL material system for infrared photodetection. In this review paper, we will present the latest development of bias-selectable multi-band infrared photodetectors at the CQD, based on InAs/GaSb/AlSb and InAs/InAs1-xSbx type-II superlattice. [reprint (PDF)]
17.	High-Average-Power, High-Duty-Cycle (~6 μm) Quantum Cascade Lasers S. Slivken, A. Evans, J. David, and M. Razeghi Applied Physics Letters, 81 (23)-- December 2, 2002 ...[Visit Journal] High-power quantum cascade lasers emitting at λ = 6.1 μm are demonstrated. Accurate control of growth parameters and strain balancing results in a near-perfect lattice match, which leads to excellent material quality. Excellent peak power for uncoated lasers, up to 1.5 W per facet for a 21 μm emitter width, is obtained at 300 K for 30 period structures. The threshold current density at 300 K is only 2.4 kA/cm². From 300 to 425 K, the laser exhibits a characteristic temperature T₀ of 167 K. Next, Y₂O₃/Ti/Au mirror coatings were deposited on 1.5 mm cavities and mounted epilayer down. These lasers show an average output power of up to 225 mW at 17% duty cycle, and still show 8 mW average power at 45% duty cycle. [reprint (PDF)]
17.	Type-II superlattice-based heterojunction phototransistors for high speed applications Jiakai Li, Arash Dehzangi, Donghai Wu, Ryan McClintock, Manijeh Razeghi Infrared Physics and Technology 108, 1033502-- May 2, 2020 ...[Visit Journal] In this study, high speed performance of heterojunction phototransistors (HPTs) based on InAs/GaSb/AlSb type-II superlattice with 30 nm base thickness and 50% cut-off wavelength of 2.0 μm at room temperature are demonstrated. We studied the relationship between -3 dB cut-off frequency of these HPT versus mesa size, applied bias, and collector layer thickness. For 8 μm diameter circular mesas HPT devices with a 0.5 μm collector layer, under 20 V applied bias voltage, we achieved a -3 dB cut-off frequency of 2.8 GHz. [reprint (PDF)]
17.	Background Limited Performance in p-doped GaAs/Ga[0.71]In[0.29]As[0.39]P[0.61] Quantum Well Infrared Photodetectors J. Hoff, S. Kim, M. Erdtmann, R. Williams, J. Piotrowski, E. Bigan, M. Razeghi and G. Brown Applied Physics Letters 67 (1)-- July 3, 1995 ...[Visit Journal] Background limited infrared photodetection has been achieved up to 100 K at normal incidence with p-type GaAs/Ga_0.71In_0.29As_0.39P_0.61 quantum well intersubband photodetectors grown by low-pressure metalorganic chemical vapor deposition. Photoresponse covers the wavelength range from 2.5 μm up to 7 μm. The device shows photovoltaic response, the cutoff wavelength increases slightly with bias, and the responsivity increases nonlinearly with bias. These effects are attributed to an asymmetric quantum well profile. [reprint (PDF)]
17.	Band gap tunability of Type-II Antimonide-based superlattices M. Razeghi and B.M. Nguyen Physics Procedia, Vol. 3, Issue 2, p. 1207-1212 (14th International Conference on Narrow Gap Semiconductors and Systems NGSS-14, Sendai, Japan, July 13-17, 2009)-- January 31, 2010 ...[Visit Journal] Current state-of-the art infrared photon detectors based on bulk semiconductors such as InSb or HgCdTe are now relatively mature and have almost attained the theoretical limit of performance. It means, however, that the technology can not be expected to demonstrate revolutionary improvements, in terms of device performances. In contrasts, low dimensional quantum systems such as superlattices, quantum wells, quantum dots, are still the development stage, yet have shown comparable performance to the bulk detector family. Especially for the Type-II Antimony-based superlattices, recent years have seen significant improvements in material quality, structural design as well as fabrication techniques which lift the performance of Type-II superlattice photodetectors to a new level. In this talk, we will discuss the advantages of Type-II-superlattices, from the physical nature of the material to the practical realisms. We will demonstrate the flexibility in controlling the energy gap and their overall band alignment for the suppression of Auger recombination, as well as to create sophisticated hetero-designs. [reprint (PDF)]
17.	Engineering the Fermi Level in NiO Thin Films D. Rogers, E. Sandana, M. Chamberlin, F. Teherani; V. Safarov, M. Konczykowski, R. Grasset, A. Alessi, H. Drouhin ; M. Razeghi SPIE OPTO PC13897 (2026) ...[Visit Journal] We investigate practical routes to engineer the Fermi level—and thus the effective work function—of p-type nickel oxide (NiO) thin films grown on c-sapphire by plasma-assisted pulsed laser deposition (PA-PLD) at room temperature (RT). We examine three levers: (i) oxygen-rich growth at low substrate temperature, (ii) post-deposition annealing in air or oxygen across 320–620 °C, and (iii) impurity (Li) acceptor doping. RT-grown NiO exhibits high crystalline quality with (111) out-of-plane orientation, narrow rocking-curve width, and a film thickness near 60 nm. RT epitaxy yields the lowest resistivity among the studied conditions, and resistance increases progressively with temperature for iso-chronic post-annealing in air. Oxygen ambient post-annealing shows no distinctive monotonic trend in resistivity, although the conductivity falls off for annealing over about 500°C. Optical transmission spectra suggest progressive healing of in-gap defect states with post-annealing temperature. Doping NiO with 20at% of Li lowers resistivity relative to undoped NiO by an order of magnitude. Post-annealing at 300°C under oxygen ambient significantly boosts conductivity. Over a decade of storage, all films exhibited significant loss of conductivity, underscoring the need for stabilisation strategies. The results map practical processing windows to tune the NiO Fermi level for integration in oxide heterojunctions (e.g., p-NiO/n-Ga2O3) used in ultraviolet detection and wide-bandgap electronics. [reprint (PDF)]
17.	High Detectivity InGaAs/InGaP Quantum-Dot Infrared Photodetectors Grown by Low Pressure Metalorganic Chemical Vapor Deposition J. Jiang, S. Tsao, T. O'Sullivan, W. Zhang, H. Lim, T. Sills, K. Mi, M. Razeghi, G.J. Brown, and M.Z. Tidrow Applied Physics Letters, 84 (12)-- April 22, 2004 ...[Visit Journal] We report a high detectivity middle-wavelength infrared quantum dot infrared photodetector (QDIP). The InGaAs quantum dots were grown by self-assembly on an InGaP matrix via low pressure metalorganic chemical vapor deposition. Photoresponse was observed at temperatures above 200 K with a peak wavelength of 4.7 µm and cutoff wavelength of 5.2 µm. The background limited performance temperature was 140 K, and this was attributed to the super low dark current observed in this QDIP. A detectivity of 3.6×10¹⁰ cm·Hz^½/W, which is comparable to the state-of-the-art quantum well infrared photodetectors in a similar wavelength range, was obtained for this InGaAs/InGaP QDIP at both T = 77 K and T = 95 K at biases of –1.6 and –1.4 V, [reprint (PDF)]
17.	Quantum cascade lasers that emit more light than heat Y. Bai, S. Slivken, S. Kuboya, S.R. Darvish and M. Razeghi Nature Photonics, February 2010, Vol. 4, p. 99-102-- February 1, 2010 ...[Visit Journal] For any semiconductor lasers, the wall plug efficiency, that is, the portion of the injected electrical energy that can be converted into output optical energy, is one of the most important figures of merit. A device with a higher wall plug efficiency has a lower power demand and prolonged device lifetime due to its reduced self-heating. Since its invention, the power performance of the quantum cascade laser has improved tremendously. However, although the internal quantum efficiency can be engineered to be greater than 80% at low temperatures, the wall plug efficiency of a quantum cascade laser has never been demonstrated above 50% at any temperature. The best wall plug efficiency reported to date is 36% at 120 K. Here, we overcome the limiting factors using a single-well injector design and demonstrate 53% wall plug efficiency at 40 K with an emitting wavelength of 5 µm. In other words, we demonstrate a quantum cascade laser that produces more light than heat. [reprint (PDF)]
17.	High-Power (~9 μm) Quantum Cascade Lasers S. Slivken, Z. Huang, A. Evans, and M. Razeghi Applied Physics Letters 80 (22)-- June 3, 2002 ...[Visit Journal] High-power quantum cascade lasers emitting at λ > 9 μm are demonstrated. Accurate control of layer thickness and interfaces is evidenced by x-ray diffraction. Excellent peak power for uncoated lasers, up to 3.5 W per facet for a 25 μm emitter width, is obtained at 300 K for 75 period structures. The threshold current density at 300 K is only 1.4 kA/cm². From 300 to 425 K, the laser exhibits a characteristic temperature, T₀, of 167 K. Over 150 mW of average power is measured per facet for a duty cycle of 6%. Simulation of the average power output reveals a thermal resistance of 12 K/W for epilayer-up mounted ridges. [reprint (PDF)]
17.	AlGaN-based deep UV light emitting diodes with peak emission below 255 nm A. Yasan, R. McClintock, K. Mayes, P. Kung, and M. Razeghi SPIE Conference, Jose, CA, Vol. 5732, pp. 197-- January 22, 2005 ...[Visit Journal] We report on the growth and fabrication of AlGaN-based deep ultraviolet light-emitting diodes (LEDs) with peak emission of below 255 nm. In order to achieve such short wavelength UV LEDs, the Al mole fractions in the device layers should be greater than ~60%. This introdues serious challenges on the growth and doping of Al_xGa_1-xN epilayers. However, with the aid of a high-quality AlN template layer and refinement of the growth conditions we have been able to demonstrate UV LEDs emitting below 255 nm. [reprint (PDF)]
17.	Monolithic Integration of GaInAs/InP Quantum Well Infrared Photodetectors on Si Substrate M. Erdtmann and M. Razeghi SPIE Conference, San Jose, CA, -- January 22, 2001 ...[Visit Journal] Using low-pressure metalorganic chemical vapor deposition, we have grown GaInAs/InP QWIP structures on GaAs-coated Si substrate. First, the procedure to optimize the epitaxy of the InP buffer layer on Si substrate is given. Excellent crystallinity and a mirror-like surface morphology were obtained by using both a two-step growth process at the beginning of the InP buffer layer growth and several series of thermal cycle annealing throughout the InP buffer layer growth. Second, results of fabricated GaInAs/InP QWIPs on Si substrate are presented. At a temperature of 80 K, the peak response wavelength occurs at 7.4 μm. The responsivities of QWIPs on both Si and InP substrates with identical structures are equal up to biases of 1.5 V. At a bias of 3 V, the responsivity of the QWIPs on Si substrate is 1.0 A/W. [reprint (PDF)]
17.	Mid-wavelength infrared high operating temperature pBn photodetectors based on type-II InAs/InAsSb superlattice Donghai Wu, Jiakai Li, Arash Dehzangi, and Manijeh Razeghi AIP Advances 10, 025018-- February 11, 2020 ...[Visit Journal] A high operating temperature mid-wavelength infrared pBn photodetector based on the type-II InAs/InAsSb superlattice on a GaSb substrate has been demonstrated. At 150 K, the photodetector exhibits a peak responsivity of 1.48 A/W, corresponding to a quantum efficiency of 47% at −50 mV applied bias under front-side illumination, with a 50% cutoff wavelength of 4.4 μm. With an R×A of 12,783 Ω·cm² and a dark current density of 1.16×10⁻⁵A/cm² under −50 mV applied bias, the photodetector exhibits a specific detectivity of 7.1×10¹¹ cm·Hz^½/W. At 300 K, the photodetector exhibits a dark current density of 0.44 A/cm²and a quantum efficiency of 39%, resultingin a specific detectivity of 2.5×10⁹ cm·Hz^½/W. [reprint (PDF)]
17.	cw phase‐locked array Ga0.25In0.75As0.5P0.5‐InP high power semiconductor laser grown by low‐pressure metalorganic chemical vapor deposition M. Razeghi; R. Blondeau; M. Krakowski; B. de Cremoux; J. P. Duchemin; F. Lozes; M. Martinot; M. A. Bensoussan Appl. Phys. Lett. 50, 230–232 (1987)-- February 2, 1987 ...[Visit Journal] Continuous and pulsed phase-locked operation of a high power GalnAsP-InP semiconductor laser emi.tting at 1.3 f1m has been achieved. The laser consists ofa seven-striped array of ridgeisland lasers fabricated by a two-step low-pressure metalorgallic chemical vapor deposition growth technique. Linear output powers greater than 300 mW (pulsed) and 120 mW (cw) have been obtained with no facet coatings. The far-field full widths at half power, both paranel and perpendicular to the junction plane, were Y and 4Y, respectively, at 10 mW (at 20°C) which is evidence for strong stripe-to-stripe coupling. [reprint (PDF)]

Page 6 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)