Center for Quantum Devices - Most Downloaded Journal Articles

Page 5 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

18.	InAs/InAs_1-xSb_x type-II superlattices for high performance long wavelength infrared detection M. Razeghi, A. Haddadi, A. M. Hoang, R. Chevallier, S. Adhikary, A. Dehzangi Proc. SPIE 9819, Infrared Technology and Applications XLII, 981909-- May 20, 2016 ...[Visit Journal] We report InAs/InAs1-xSbx type-II superlattice base photodetector as high performance long-wavelength infrared nBn device grown on GaSb substrate. The device has 6 μm-thick absorption region, and shows optical performance with a peak responsivity of 4.47 A/W at 7.9 μm, which is corresponding to the quantum efficiency of 54% at a bias voltage of negative 90 mV, where no anti-reflection coating was used for front-side illumination. At 77K, the photodetector’s 50% cut-off wavelength was ~10 μm. The device shows the detectivity of 2.8x10¹¹ cm•Hz^½/W at 77 K, where RxA and dark current density were 119 Ω•cm² and 4.4x10^-4 A/cm² , respectively, under -90 mV applied bias voltage [reprint (PDF)]
18.	High Power, Room Temperature InP-Based Quantum Cascade Laser Grown on Si Steven Slivken and Manijeh Razeghi Journal of Quantum Electronics, Vol. 58, No. 6, 2300206 ...[Visit Journal] We report on the realization of an InP-based long wavelength quantum cascade laser grown on top of a silicon substrate. This demonstration first required the development of an epitaxial template with a smooth surface, which combines two methods of dislocation filtering. Once wafer growth was complete, a lateral injection buried heterostructure laser geometry was employed for efficient current injection and low loss. The laser emits at a wavelength of 10.8 μm and is capable of operation above 373 K, with a high peak power (>4 W) at room temperature. Laser threshold behavior with temperature is characterized by a T0 of 178 K. The far field beam shape is single lobed, showing fundamental transverse mode operation. [reprint (PDF)]
18.	Optical Coatings by ion-beam sputtering deposition for long-wave infrared quantum cascade lasers J. Nguyen, J.S. Yu, A. Evans, S. Slivken and M. Razeghi Applied Physics Letters, 89 (11)-- September 11, 2006 ...[Visit Journal] The authors report on the development of high-reflection and multilayer antireflection coatings using ion-beam sputtering deposition for long-wave infrared (λ~9.4 μm) quantum cascade lasers. A metallic high-reflection coating structure using Y₂O₃ and Au is demonstrated to achieve a high reflectance of 96.70%, and the use of a multilayer anti-reflection coating structure using PbTe and ZnO is demonstrated to achieve a very low reflectance of 1.64%. [reprint (PDF)]
18.	Photovoltaic MWIR type-II superlattice focal plane array on GaAs substrate E.K. Huang, P.Y. Delaunay, B.M. Nguyen, S. Abdoullahi-Pour, and M. Razeghi IEEE Journal of Quantum Electronics (JQE), Vol. 46, No. 12, p. 1704-1708-- December 1, 2010 ...[Visit Journal] Recent improvements in the performance of Type-II superlattice (T2SL) photodetectors has spurred interest in developing low cost and large format focal plane arrays (FPA) on this material system. Due to the limitations of size and cost of native GaSb substrates, GaAs is an attractive alternative with 8” wafers commercially available, but is 7.8% lattice mismatched to T2SL. In this paper, we present a photovoltaic T2SL 320 x 256 focal plane array (FPA) in the MWIR on GaAs substrate. The FPA attained a median noise equivalent temperature difference (NEDT) of 13 mK and 10mK (F#=2.3) with integration times of 10.02 ms and 19.06 ms respectively at 67 K. [reprint (PDF)]
18.	Generation-recombination and trap-assisted tunneling in long wavelength infrared minority electron unipolar photodetectors based on InAs/GaSb superlattice F. Callewaert, A.M. Hoang, and M. Razeghi Applied Physics Letters, 104, 053508 (2014)-- February 6, 2014 ...[Visit Journal] A long wavelength infrared minority electron unipolar photodetector based on InAs/GaSb type-II superlattices is demonstrated. At 77 K, a dark current of 3 × 10⁻⁵ A/cm² and a differential resistance-area of 3 700 Ω·cm² are achieved at the turn-on bias, with a 50%-cutoff of 10.0 μm and a specific detectivity of 6.2 × 10¹¹ Jones. The dark current is fitted as a function of bias and temperature using a model combining generation-recombination and trap-assisted tunneling. Good agreement was observed between the theory and the experimental dark current. [reprint (PDF)]
18.	World's first demonstration of type-II superlattice dual band 640 x 512 LWIR focal plane array E.K. Huang and M. Razeghi SPIE Proceedings, Vol. 8268, p. 82680Z-- January 22, 2012 ...[Visit Journal] High resolution multi-band infrared detection of terrestrial objects is useful in applications such as long range and high altitude surveillance. In this paper, we present a 640 x 512 type-II superlattice focal plane array (FPA) in the long-wave infrared (LWIR) suitable for such purposes, featuring 100% cutoff wavelengths at 9.5 μm (blue channel) and 13 μm (red). The dual band camera is single-bump hybridized to an Indigo 30 μm pitch ISC0905 read-out integrated circuit. Test pixels revealed background limited behavior with specific detectivities as high as ~5x10¹¹ Jones at 7.9 μm (blue) and ~1x10¹¹ Jones at 10.2 μm (red) at 77K. [reprint (PDF)]
18.	Al_xGa_1-xN Materials and Device Technology for Solar Blind Ultraviolet Photodetector Applications R. McClintock, P. Sandvik, K. Mi, F. Shahedipour, A. Yasan, C. Jelen, P. Kung, and M. Razeghi SPIE Conference, San Jose, CA, Vol. 4288, pp. 219-- January 22, 2001 ...[Visit Journal] There has been a growing interest for the development of solar blind ultraviolet (UV) photodetectors for use in a variety of applications, including early missile threat warning, flame monitoring, UV radiation monitoring and chemical/biological reagent detection. The Al_xGa_1-xN material system has emerged as the most promising approach for such devices. However, the control of the material quality and the device technology are still rather immature. We report here the metalorganic chemical vapor deposition, the n-type and the p-type doping of high quality Al_xGa_1-xN thin films on sapphire substrates over a wide range of Al concentration. [reprint (PDF)]
18.	Phase-locked, high power, mid-infrared quantum cascade laser array W. Zhou, S. Slivken, and M. Razeghi Applied Physics Letters 112, 181106-- May 4, 2018 ...[Visit Journal] We demonstrate phase-locked, high power quantum cascade laser arrays, which are combined using a monolithic, tree array multimode interferometer, with emission wavelengths around 4.8 μm. A maximum output power of 15 W was achieved from an eight-element laser array, which has only a slightly higher threshold current density and a similar slope efficiency compared to a Fabry-Perot laser of the same length. Calculated multimode interferometer splitting loss is on the order of 0.27 dB for the in-phase supermode. In-phase supermode operation with nearly ideal behavior is demonstrated over the working current range of the array. [reprint (PDF)]
18.	Quantum Sensing Using Type-II InAs/GaSb Superlattice for Infrared Detection M. Razeghi, A. Gin, Y. Wei, J. Bae, and J. Nah Microelectronics Journal, 34 (5-8)-- May 1, 2003 ...[Visit Journal] Large, regular arrays of bulk GaSb and InAs/GaSb Type-II superlattice pillars have been fabricated by electron beam lithography and dry etching. A 2.5 keV electron beam lithography system and metal evaporation are used to form the Au mask on superlattice and bulk substrates. Dry etching of these materials has been developed with BCl3:Ar, CH4:H2:Ar and cyclic CH₄:H₂:Ar/O₂ plasmas. Etch temperatures were varied from 20 to 150 °C. The diameter of the superlattice pillars was below 50 nm with regular 200 nm spacing. Bulk GaSb pillars were etched with diameters below 20 nm. Areas of dense nanopillars as large as 500 μm×500 μm were fabricated. The best height/diameter aspect ratio was approximately 10:1. To date, these are the smallest diameter III–V superlattice pillar structures reported, and the first nanopillars in the InAs/GaSb material system. The basic theory of these devices and surface passivation with SiO₂ and Si₃N₄ thin films has also been discussed. [reprint (PDF)]
18.	Dark current suppression in Type-II InAs/GaSb superlattice long wavelength infrared photodiodes with M-structure barrier B.M. Nguyen, D. Hoffman, P.Y. Delaunay, and M. Razeghi Applied Physics Letters, Vol. 91, No. 16, p. 163511-1-- October 15, 2007 ...[Visit Journal] We presented an alternative design of Type-II superlattice photodiodes with the insertion of a mid-wavelength infrared M-structure AlSb/GaSb/InAs/GaSb/AlSb superlattice for the reduction of dark current. The M-structure superlattice has a larger carrier effective mass and a greater band discontinuity as compared to the standard Type-II superlattices at the valence band. It acts as an effective medium that weakens the diffusion and tunneling transport at the depletion region. As a result, a 10.5 µm cutoff Type-II superlattice with 500 nm M-superlattice barrier exhibited a R₀A of 200 cm² at 77 K, approximately one order of magnitude higher than the design without the barrier. The quantum efficiency of such structures does not show dependence on either barrier thickness or applied bias. [reprint (PDF)]
18.	Metalorganic chemical vapor deposition of monocrystalline GaN thin films on β-LiGaO2substrates P. Kung, A. Saxler, X. Zhang, D. Walker, R. Lavado, and M. Razeghi Applied Physics Letters 69 (14)-- September 30, 1996 ...[Visit Journal] We report the metalorganic chemical vapor deposition growth and characterization of monocrystalline GaN thin films on β-LiGaO₂ substrates. The influence of the growth temperature on the crystal quality was studied. The structural, electrical, and optical properties of the films were assessed through scanning electron microscopy, x-ray diffraction, Hall measurements, optical transmission, photoluminescence. [reprint (PDF)]
18.	Room temperature quantum cascade lasers with 22% wall plug efficiency in continuous-wave operation F. Wang, S. Slivken, D. H. Wu, and M. Razeghi Optics Express Vol. 28, Issue 12, pp. 17532-17538-- June 8, 2020 ...[Visit Journal] We report the demonstration of quantum cascade lasers (QCLs) with improved eﬃciency emitting at a wavelength of 4.9 µm in pulsed and continuous-wave(CW)operation. Based on an established design and guided by simulation, the number of QCL-emitting stages is increased in order to realize a 29.3% wall plug eﬃciency (WPE) in pulsed operation at room temperature. With proper fabrication and packaging, a 5-mm-long, 8-µm-wide QCL with a buried ridge waveguide is capable of 22% CW WPE and 5.6 W CW output power at room temperature. This corresponds to an extremely high optical density at the output facet of ∼35 MW/cm², without any damage. [reprint (PDF)]
18.	Recent Advances in Room Temperature, High-Power Terahertz Quantum Cascade Laser Sources Based on Difference-Frequency Generation Quanyong Lu and Manijeh Razeghi Photonics, 3, 42-- July 7, 2016 ...[Visit Journal] We present the current status of high-performance, compact, THz sources based on intracavity nonlinear frequency generation in mid-infrared quantum cascade lasers. Significant performance improvements of our THz sources in the power and wall plug efficiency are achieved by systematic optimizing the device’s active region, waveguide, and chip bonding strategy. High THz power up to 1.9 mW and 0.014 mW for pulsed mode and continuous wave operations at room temperature are demonstrated, respectively. Even higher power and efficiency are envisioned based on enhancements in outcoupling efficiency and mid-IR performance. Our compact THz device with high power and wide tuning range is highly suitable for imaging, sensing, spectroscopy, medical diagnosis, and many other applications. [reprint (PDF)]
18.	Tight-binding theory for the thermal evolution of optical band gaps in semiconductors and superlattices S. Abdollahi Pour, B. Movaghar, and M. Razeghi American Physical Review, Vol. 83, No. 11, p. 115331-1-- March 15, 2011 ...[Visit Journal] A method to handle the variation of the band gap with temperature in direct band-gap III–V semiconductors and superlattices using an empirical tight-binding method has been developed. The approach follows closely established procedures and allows parameter variations which give rise to perfect fits to the experimental data. We also apply the tight-binding method to the far more complex problem of band structures in Type-II infrared superlattices for which we have access to original experimental data recently acquired by our group. Given the close packing of bands in small band-gap Type-II designs, k·p methods become difficult to handle, and it turns out that the sp3s* tight-binding scheme is a practical and powerful asset. Other approaches to band-gap shrinkage explored in the past are discussed, scrutinized, and compared. This includes the lattice expansion term, the phonon softening mechanism, and the electron-phonon polaronic shifts calculated in perturbation theory. [reprint (PDF)]
18.	Type-II InAs/GaSb Superlattices and Detectors with Cutoff Wavelength Greater Than 18 μm M. Razeghi, Y. Wei, A. Gin, G.J. Brown and D. Johnstone Proceedings of the SPIE, San Jose, CA, Vol. 4650, 111 (2002)-- January 25, 2002 ...[Visit Journal] The authors report the most recent advances in Type-II InAs/GaSb superlattice materials and photovoltaic detectors. Lattice mismatch between the substrate and the superlattice has been routinely achieved below 0.1%, and less than 0.0043% as the record. The FWHM of the zeroth order peak from x-ray diffraction has been decreased below 50 arcsec and a record of less than 44arcsec has been achieved. High performance detectors with 50% cutoff beyond 18 micrometers up to 26 micrometers have been successfully demonstrated. The detectors with a 50% cut-off wavelength of 18.8 micrometers showed a peak current responsivity of 4 A/W at 80K, and a peak detectivity of 4.5¹⁰ cm·Hz^½·W^-1 was achieved at 80K at a reverse bias of 110 mV under 300 K 2(pi) FOV background. Some detectors showed a projected 0% cutoff wavelength up to 28~30 micrometers . The peak responsivity of 3Amp/Watt and detectivity of 4.25¹⁰ cm·Hz^½·W^-1 was achieved under -40mV reverse bias at 34K for these detectors. [reprint (PDF)]
18.	Determination of of Band Gap Energy of Al_1-xIn_xN Grown by Metal Organic Chemical Vapor Deposition in the High Al Composition Regime K.S. Kim, A. Saxler, P. Kung, M. Razeghi, and K.Y. Lim Applied Physics Letters 71 (6)-- August 11, 1997 ...[Visit Journal] Ternary AlInN was grown by metal–organic chemical-vapor deposition in the high Al composition regime. The band-gap energy of AlInN ternary was measured by optical absorption spectroscopy at room temperature. The band-gap energy of Al_0.92In_0.08N is 5.26 eV. The potential application of AlInN as a barrier material for GaN is also discussed. [reprint (PDF)]
18.	Long Wavelength Type-II Photodiodes Operating at Room Temperature H. Mohseni and M. Razeghi IEEE Photonics Technology Letters 13 (5)-- May 1, 2001 ...[Visit Journal] The operation of uncooled InAs-GaSb superlattice photodiodes with a cutoff wavelength of λc=8 μm and a peak detectivity of 1.2 × 10⁸ cm·Hz^½/W at zero bias is demonstrated. The detectivity is similar to the best uncooled HgCdTe detectors and microbolometers. However, the R0A product is more than two orders of magnitude higher than HgCdTe and the device is more than four orders of magnitude faster than microbolometers. These features combined with their low 1/f noise and high uniformity make these type-II photodiodes an excellent choice for uncooled high-speed IR imaging arrays [reprint (PDF)]
18.	High performance quantum cascade lasers (~11 μm) operating at high temperature (T>= 425K) A. Tahraoui, A. Matlis, S. Slivken, J. Diaz, and M. Razeghi Applied Physics Letters 78 (4)-- January 22, 2001 ...[Visit Journal] We report record-low threshold current density and high output power for λ ∼ 11 μm Al_0.48In_0.52As/Ga_0.47In_0.53As quantum cascade lasers operating up to 425 K. The threshold current density is 1.1, 3.83, and 7.08 kA/cm² at 80, 300, and 425 K, respectively, for 5 μs pulses at a 200 Hz repetition rate. The cavity length is 3 mm with a stripe width of 20 μm. The maximum peak output power per facet is 1 W at 80 K, 0.5 W at 300 K, and more than 75 mW at 425 K. The characteristic temperature of these lasers is 174 K between 80 and 300 K and 218 K in the range of 300–425 K. [reprint (PDF)]
17.	Low threshold GaInAsP/InP lasers with good temperature dependence grown by low pressure MOVPE J.-P. Hirtz, M. Razeghi, J.-P. Larivain, S. Hersee, J.-P. Duchemin Electronics Letters Volume 17, Issue 3 https://doi.org/10.1049/el:19810081-- February 1, 1981 ...[Visit Journal] Room temperature pulsed operation has been achieved in the 1.2–1.3 μm region for GaInAsP/InP lasers grown by low pressure metalorganic vapour phase epitaxy. Thresholds as low as 1.2 kA/cm2 and threshold temperature dependences of exp T/T0, with T0 up to 80 K, have been obtained. [reprint (PDF)]
17.	Thermal imaging based on high-performance InAs/InP quantum-dot infrared photodetector operating at high temperature M. Razeghi; H. Lim; S. Tsao; H. Seo; W. Zhang Conference Proceedings - Lasers and Electro-Optics Society Annual Meeting-LEOS.15-16:[4382251] (2007).-- October 21, 2007 ...[Visit Journal] We report a room temperature operating and high-performance InAs quantum-dot infrared photodetector on InP substrate and thermal imaging of 320times256 focal plane array based on this device up to 200 K. [reprint (PDF)]
17.	Widely tuned room temperature terahertz quantum cascade laser sources based on difference-frequency generation Q.Y. Lu, N. Bandyopadhyay, S. Slivken, Y. Bai and M. Razeghi Applied Physics Letters, Vol. 101, No. 25, p. 251121-1-- December 17, 2012 ...[Visit Journal] We demonstrate room temperature THz quantum cascade laser sources with a broad spectral coverage based on intracavity difference-frequency generation. Two mid-infrared active cores based on the single-phonon resonance scheme are designed with a THz nonlinearity specially optimized at the high operating fields that correspond to the highest mid-infrared output powers. A Čerenkov phase-matching scheme along with integrated dual-period distributed feedback gratings are used for efficient THz extraction and spectral purification. Single mode emissions from 1.0 to 4.6 THz with a side-mode suppression ratio and output power up to 40 dB and 32 μW are obtained, respectively. [reprint (PDF)]
17.	Phase-matched optical second-harmonic generation in GaN and AlN slab waveguides D.N. Hahn, G.T. Kiehne, G.K.L. Wong, J.B. Ketterson, P. Kung, A. Saxler and M. Razeghi Journal of Applied Physics 85 (5)-- March 1, 1999 ...[Visit Journal] Phase-matched optical second-harmonic (SH) generation was observed in GaN and AlN slab waveguides. Phase matching was achieved by waveguide modal dispersion. By tuning the output wavelength of an optical parametric amplifier, several phased-matched SH peaks were observed in the visible spectrum covering blue to red wavelengths. The peak positions are in agreement with the values calculated using the dispersive refractive indices of the film and substrate materials. [reprint (PDF)]
17.	InSb Infrared Photodetectors on Si Substrates Grown by Molecular Beam Epitaxy E. Michel, J. Xu, J.D. Kim, I. Ferguson, and M. Razeghi IEEE Photonics Technology Letters 8 (5) pp. 673-- May 1, 1996 ...[Visit Journal] The InSb infrared photodetectors grown heteroepitaxially on Si substrates by molecular beam epitaxy (MBE) are reported. Excellent InSb material quality is obtained on 3-in Si substrates (with a GaAs predeposition) as confirmed by structural, optical, and electrical analysis. InSb infrared photodetectors on Si substrates that can operate from 77 K to room temperature have been demonstrated. The peak voltage-responsitivity at 4 μm is about 1.0×10³ V/W and the corresponding Johnson-noise-limited detectivity is calculated to be 2.8×10¹⁰ cm·Hz^½/W. This is the first important stage in developing InSb detector arrays or monolithic focal plane arrays (FPAs) on silicon. The development of this technology could provide a challenge to traditional hybrid FPA's in the future. [reprint (PDF)]
17.	Comparison of Gain and Threshold Current Density for InGaAsP/GaAs λ = 808 nm) Lasers with Different Quantum-Well Thickness H.J. Yi, J. Diaz, I. Eliashevich, G. Lukas, S. Kim, D. Wu, M. Erdtmann, C. Jelen, S. Slivken, L.J. Wang, and M. Razeghi Journal of Applied Physics 79 (11)-- July 1, 1996 ...[Visit Journal] We investigated the quantum‐size effects of quantum well (QW) on gain and threshold current density for InGaAsP/GaAs (λ=808 nm) laser diodes. In this work, a comparison is made of lasers with different QW thickness while keeping the optical confinement factors constant. We found that the threshold current density and differential efficiency were not affected by narrowing the QW thickness. The theoretical model taking into account the mixing of the valence bands and momentum relaxation for InGaAsP/GaAs lasers with spontaneous emission (optically pumped) measurement shows that the absence of difference between these structures can be attributed to the high relaxation rate. [reprint (PDF)]
17.	Tl incorporation in InSb and lattice contraction of In_1-xTl_xSb J.J. Lee and M. Razeghi Applied Physics Letters 76 (3)-- January 17, 2000 ...[Visit Journal] Ternary In_1−xTl_xSb thin films are grown by low pressure metalorganic chemical vapor deposition in the high In composition region. Infrared photoresponse spectra of the In_1−xTl_xSb epilayers show a clear shift toward a longer wavelength compared to that of InSb. Tl incorporation is confirmed by Auger electron spectroscopy. In contrast to the theoretical expectation, high resolution x-ray diffraction study reveals that the lattice of the In_1−xTl_xSb epilayers is contracted by the incorporation of Tl. As more Tl is incorporated, the lattice contraction is observed to increase gradually in the experimental range. A possible origin of this phenomenon is discussed. Our experimental results suggest that the Tl incorporation behavior in In_1−xTl_xSb differs from that of other group III impurities in III antimonides. [reprint (PDF)]

Page 5 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)