Center for Quantum Devices - Most Downloaded Journal Articles

Page 4 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

19.	High quantum efficiency mid-wavelength infrared type-II InAs/InAs_1-xSb_x superlattice photodiodes grown by metal-organic chemical vapor deposition Donghai Wu , Quentin Durlin, Arash Dehzangi , Yiyun Zhang , and Manijeh Razeghi Appl. Phys. Lett. 114, 011104-- January 8, 2019 ...[Visit Journal] We report the growth and characterization of mid-wavelength infrared type-II InAs/InAs_1-xSb_x superlattice photodiodes on GaSb substrates grown by metal-organic chemical vapor deposition. At 150 K, the 50% cut-off wavelength is 5.0 um, the dark current density is 3.3x10⁻⁴ A/cm² under −20mV bias, and the peak responsivity is 1.76A/W corresponding to a quantum efficiency of 55% without anti-reflection coating. A specific detectivity of 1.2x10¹¹cmHz^1/2/W is achieved at 4.0 um under −20mV bias at 150 K. [reprint (PDF)]
19.	Type-II ‘M’ Structure Photodiodes: An Alternative Material Design for Mid-Wave to Long Wavelength Infrared Regimes B-M. Nguyen, M. Razeghi, V. Nathan, and G.J. Brown SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64790S-1-10-- January 29, 2007 ...[Visit Journal] In this work, an AlSb-containing Type-II InAs/GaSb superlattice, the so-called M-structure, is presented as a candidate for mid and long wavelength infrared detection devices. The effect of inserting an AlSb barrier in the GaSb layer is discussed and predicts many promising properties relevant to practical use. A good agreement between the theoretical calculation based on Empirical Tight Binding Method framework and experimental results is observed, showing the feasibility of the structure and its properties. A band gap engineering method without material stress constraint is proposed. [reprint (PDF)]
19.	GalnAs AND GaInAsP MATERIALS GROWN BY LOW PRESSURE MOCVD FOR MICROWAVE AND OPTOELECTRONIC APPLICATIONS J.P. Duchemin, J.P. Hirtz, M. Razeghi, M. Bonnet , S.D. Hersee J.P. Duchemin, J.P. Hirtz, M. Razeghi, GaInAs and GaInAsP materials grown by low pressure MOCVD for microwave and optoelectronic applications, Journal of Crystal Growth, 55, 1, 1981, Pages 64-73,-- August 1, 1981 ...[Visit Journal] The low pressure MOCVD technique has been successfully used to grow GaInAsP, lattice-matched to InP, for the complete compositional range between InP (λ=0.91 μm) and the ternary compound Ga0.47In0.53As (λ=1.67 μm). By contrast to LPE growth it has been found that during the MOCVD growth of double heterostructures InP can be grown directly onto the ternary or quaternary with no disturbance of the active layer, i.e. there is no effect equivalent to “melt back”. The compositional grading on both sides of the active layer was measured by scanning Auger spectroscopy on bevelled samples. It was found that the graded regions were typically less than 100 Å wide for GaInAsP active layers and less than 50 Å wide for GaInAs active layers. Single layers of undoped GaInAs exhibited a typical mobility of 6700 cm2 V-1s-1 at 1.5×1017 cm-3. The compositional uniformity of the ternary layers was characterised by measurement of the photoluminescence wavelength at various points on a large sample. The wavelength varied by <3 nm over 95% of the area, which was approximately 8 cm2. Our early MOCVD grown GaInAsP/InP DH lasers exhibited high thresholds due to a poor interface between the p-InP and the active layer. However, recently fabricated broad area lasers emitting at 1.27 μm show an average threshold current density of 1.5 kA cm-2 with a T0 of between 70 to 80 K. Stripe geometry lasers have being fabricated from this material and CW operation has been obtained. [reprint (PDF)]
18.	Al_xGa_1-xN for Solar-Blind UV Detectors P. Sandvik, K. Mi, F. Shahedipour, R. McClintock, A. Yasan, P. Kung, and M. Razeghi Journal of Crystal Growth 231 (2001)-- January 1, 2001 ...[Visit Journal] We report on the metalorganic chemical vapor deposition of high quality AlGaN thin films on sapphire substrates over a wide range of Al concentrations. The quality of these AlGaN materials was verified through a demonstration of high performance visible and solar-blind UV p–i–n photodiodes with peak cutoff wavelengths ranging from 227 to 364 nm. External quantum efficiencies for these devices reached as high as 69% with over five orders rejection ratio from the peak to visible wavelengths. [reprint (PDF)]
18.	Dispersion compensated mid-infrared quantum cascade laser frequency comb with high power output Q. Y. Lu, S. Manna, S. Slivken, D. H. Wu, and M. Razeghi AIP Advances 7, 045313 -- April 26, 2017 ...[Visit Journal] Chromatic dispersion control plays an underlying role in optoelectronics and spectroscopy owing to its enhancement to nonlinear interactions by reducing the phase mismatching. This is particularly important to optical frequency combs based on quantum cascade lasers which require negligible dispersions for efficient mode locking of the dispersed modes into equally spaced comb modes. Here, we demonstrated a dispersion compensated mid-IR quantum cascade laser frequency comb with high power output at room temperature. A low-loss dispersive mirror has been engineered to compensate the device’s dispersion residue for frequency comb generation. Narrow intermode beating linewidths of 40 Hz in the comb-working currents were identified with a high power output of 460 mW and a broad spectral coverage of 80 cm^-1. This dispersion compensation technique will enable fast spectroscopy and high-resolution metrology based on QCL combs with controlled dispersion and suppressed noise. [reprint (PDF)]
18.	Optoelectronic Devices Based on III-V Compound Semiconductors Which Have Made a Major Scientific and Technological Impact in the Past 20 Years M. Razeghi IEEE Journal of Selected Topics in Quantum Electronics 6 (6), pp.1344 - 1354 -- November 1, 2000 ...[Visit Journal] This paper reviews some of our pioneering contributions to the field of III–V compound semiconductor materials and low-dimensional optoelectronic devices. These contributions span from the ultraviolet (200 nm) up to the far-infrared (25 μm) portion of the electromagnetic spectrum and have had a major scientific and technological impact on the semiconductor world in the past 20 years. [reprint (PDF)]
18.	Conduction‐ and valence‐band offsets in GaAs/Ga0.51In0.49P single quantum wells grown by metalorganic chemical vapor deposition D. Biswas; N. Debbar; P. Bhattacharya; M. Razeghi; M. Defour; F. Omnes Appl. Phys. Lett. 56, 833–835 (1990)-- February 26, 1990 ...[Visit Journal] We have independently estimated the conduction- and valence-band offsets D.Ec and D.Ev in GaAs/Gao . 51 Ino49 P quantum wells by measuring the capacitance transient resulting from thermal emission of carriers from the respective wens. The heterostructure samples were grown by low-pressure metalorganic chemical vapor deposition. The band offsets are extrapolated from the emission activation energies with appropriate corrections. The estimated values of AEc and AEv are 0.198 and 0.285 eV, respectively. [reprint (PDF)]
18.	High performance GaAs/GaInP heterostructure bipolar transistors grown by low-pressure metal-organic chemical vapour deposition M Razeghi, F Omnes, M Defour, P Maurel, J Hu, E Wolk and D Pavlidis M Razeghi et al 1990 Semicond. Sci. Technol. 5 278-- December 11, 1989 ...[Visit Journal] The authors report the fabrication of high-quality GaAs/GaInP n-p-n heterojunction bipolar transistors grown by low-pressure metal-organic chemical vapour deposition on semi-insulating substrates. Various structures with homogeneous and graded bases have been fabricated. Doping profiles together with X-ray double diffraction patterns demonstrate the excellent control of growth parameters such as thicknesses, doping levels and interface quality. The static characteristics of the devices show current gains as high as 400, which is the highest value reported in that system [reprint (PDF)]
18.	AlGaN/AlN MOVPE heteroepitaxy: pulsed co-doping SiH4 and TMIn Ilkay Demir, Yusuf Koçak, A. Emre Kasapoğlu, Manijeh Razeghi, Emre Gür and Sezai Elagoz Semicond. Sci. Technol. 34 075028-- June 24, 2019 ...[Visit Journal] We report a new growth approach pulsed co-doping growth of Al_xGa_1−xN (x > 0.5) epilayers on AlN/Al₂O₃ templates by metal organic vapor phase epitaxy (MOVPE). Using this approach SiH₄ (silane) and TMIn (trimethylindium) supplied to the growth chamber alternately and pulsed during the growth of AlGaN epilayers. Structural and morphological quality of AlGaN epilayers were investigated by high resolution x-ray diffraction (HR-XRD), atomic force microscopy (AFM), Raman spectroscopy, and scanning electron microscopy (SEM) techniques. It has shown that higher crystalline quality with low full width at half maximum (FWHM) and smoother surface morphology with reduced hexagonal hillock density has been obtained by the pulsed co-doping growth approach. Volcano like hillock structures has been confirmed by Raman mapping. [reprint (PDF)]
18.	Light People: Professor Manijeh Razeghi Hui Wang, and Cun Yu Light Sci Appl 13, 164 ...[Visit Journal] Editorial The sense of light is the first sensation the human body develops. The importance of light is self-evident. However, we all know that the light we can see and perceive covers only a small section of the spectrum. Today, for Light People, we feature a researcher who is committed to exploring different spectral bands of light ranging from deep ultraviolet to terahertz waves and working on quantum semiconductor technology, Prof. Manijeh Razeghi of the Northwestern University in the United States. Known for her quick thinking and witty remarks, Prof. Razeghi is passionate about life and always kind to others. As a scientist, she does not limit her research to a single focus, instead, she works on the entire process from material selection, device design, processing, and manufacturing, all the way to product application. She has a strong passion for education, a commitment unwavered by fame or fortune. For her students, she is both a reliable source of knowledge and a motherly figure with a caring heart. She firmly believes that all things in nature can give her energy and inspiration. In science, she is a true “pioneer” in research and a “miner” of scientific discoveries. She advises young scientists to enjoy and love what they do, and turn their research into their hobby. As a female scientist, she calls on all women to realize their true value and potential. Next, let’s hear from Professor Manijeh Razeghi, a true star who radiates energy and light [reprint (PDF)]
18.	Type-II InAs/GaSb superlattice photovoltaic detectors with cutoff wavelength approaching 32 μm Y. Wei, A. Gin, M. Razeghi and G.J. Brown Applied Physics Letters, 81 (19)-- November 4, 2002 ...[Visit Journal] We report the most recent advance in the area of type-II InAs/GaSb superlattice photovoltaic detectors that have cutoff wavelengths beyond 25 μm, with some at nearly 32 μm. The photodiodes with a heterosuperlattice junction showed Johnson noise limited peak detectivity of 1.05 x 10¹⁰ cm Hz^½/W at 15 μm under zero bias, and peak responsivity of 3 A/W under -40 mV reverse bias at 34 K illuminated by ~300 K background with a 2π field-of-view. The maximum operating temperature of these detectors ranges from 50 to 65 K. No detectable change in the blackbody response has been observed after 5-6 thermal cyclings, with temperature varying between 15 and 296 K in vacuum. [reprint (PDF)]
18.	Performance enhancement of GaN ultraviolet avalanche photodiodes with p-type delta-doping C. Bayram, J.L. Pau, R. McClintock and M. Razeghi Applied Physics Letters, Vol. 92, No. 24, p. 241103-1-- June 16, 2008 ...[Visit Journal] High quality delta-doped p-GaN is used as a means of improving the performance of back-illuminated GaN avalanche photodiodes (APDs). Devices with delta-doped p-GaN show consistently lower leakage current and lower breakdown voltage than those with bulk p-GaN. APDs with delta-doped p-GaN also achieve a maximum multiplication gain of 5.1×10⁴, more than 50 times higher than that obtained in devices with bulk p-GaN. The better device performance of APDs with delta-doped p-GaN is attributed to the higher structural quality of the p-GaN layer achieved via delta-doping. [reprint (PDF)]
18.	Active and passive infrared imager based on short-wave and mid-wave type-II superlattice dual-band detectors E.K. Huang, A. Haddadi, G. Chen, A.M. Hoang, and M. Razeghi Optics Letters, Vol. 38, no. 1, p. 22-24-- January 1, 2013 ...[Visit Journal] A versatile dual-band detector capable of active and passive use is demonstrated using short-wave (SW) and midwave(MW) IR type-II superlattice photodiodes. A bilayer etch-stop scheme is introduced for back-side-illuminated detectors, which enhanced the external quantum efficiency both in the SWIR and MWIR spectral regions. Temperature-dependent dark current measurements of pixel-sized 27 μm detectors found the dark current density to be ~1 × 10^-5 A/cm² for the ∼4.2 μm cutoff MWIR channel at 140 K. This corresponded to a reasonable imager noise equivalent difference in temperature of ∼49 mK using F∕2.3 optics and a 10 ms integration time (t_int), which lowered to ∼13 mK at 110 K using tint 30 ms, illustrating the potential for high-temperature operation. The SWIR channel was found to be limited by readout noise below 150 K. Excellent imagery from the dual-band imager exemplifying pixel coincidence is shown. [reprint (PDF)]
18.	Dual section quantum cascade lasers with wide electrical tuning S. Slivken, N. Bandyopadhyay, S. Tsao, S. Nida, Y. Bai, Q.Y. Lu and M. Razeghi SPIE Proceedings, Vol. 8631, p. 86310P-1, Photonics West, San Francisco, CA-- February 3, 2013 ...[Visit Journal] This paper describes our development efforts at Northwestern University regarding dual-section sampled grating distributed feedback (SGDFB) QCLs. These devices are the same size, but have much wider electrical tuning, than a traditional DFB laser. In this paper, I will show how we have dramatically extended the monolithic tuning range of high power quantum cascade lasers with high side mode suppression. This includes individual laser element tuning of up to 50 cm^-1 and 24 dB average side mode suppression. These lasers are capable of room temperature continuous operation with high power (>100 mW) output. Additionally, we have demonstrated a broad spectral coverage of over 350 cm^-1 on a single chip, which is equivalent to 87.5% of the gain bandwidth. The eventual goal is to realize an extended array of such laser modules in order to continuously cover a similar or broader spectral range, similar to an external cavity device without any external components. [reprint (PDF)]
18.	Growth and characterization of long wavelength infrared Type-II superlattice Photodiodes on a 3 B.M. Nguyen, G. Chen, M.A. Hoang, and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-27, 2011), Vol. 7945, p. 79451O-- January 23, 2011 ...[Visit Journal] One of the great advantages of Type-II InAs/GaSb superlattice over other competing technologies for the third generation infrared imagers is the potential to have excellent uniformity across a large area as the electronic structure of the material is controlled by the layer thicknesses, not by the composition of the materials. This can economize the material growth, reduce the fabrication cost, and especially allow the realization of large format imagers. In this talk, we report the molecular beam epitaxial growth of Type-II superlattices on a 3-inch GaSb substrate for long wavelength infrared detection. The material exhibits excellent structural, optical and electrical uniformity via AFM, Xray, quantum efficiency and I-V measurements. At 77K, 11μm cutoff photodiodes exhibit more than 45% quantum efficiency, and a dark current density of 1.0x10^-4 A/cm² at 50 mV, resulting in a specific detectivity of 6 x 10¹¹ cm·Hz^1/2/W. [reprint (PDF)]
18.	*High quality AlN and GaN epilayers grown on (001) sapphire, (100) and (111) silicon substrates P. Kung, A. Saxler, X. Zhang, D. Walker, T.C. Wang, I. Ferguson, and M. Razeghi Applied Physics Letters 66 (22)-- May 29, 1995** ...[Visit Journal] The growth of high quality AlN and GaN thin films on basal plane sapphire, (100), and (111) silicon substrates is reported using low pressure metalorganic chemical vapor deposition. X-ray rocking curve linewidths of about 100 and 30 arcsec were obtained for AlN and GaN on sapphire, respectively. Room‐temperature optical transmission and photoluminescence (of GaN) measurements confirmed the high quality of the films. The luminescence at 300 and 77 K of the GaN films grown on basal plane sapphire, (100), and (111) silicon was compared. [reprint (PDF)]
18.	High Performance Planar Antimony-Based Superlattice Photodetectors Using Zinc Diffusion Grown by MBE Jiakai Li, R. K. Saroj, Steven Slivken, V. H. Nguyen, Gail Brown and Manijeh Razeghi Photonics 2022, 9, 664 ...[Visit Journal] In this letter, we report a mid-wavelength infrared (MWIR) planar photodetector based on InAs/InAsSb type-II superlattices (T2SLs) that has a cut-off wavelength of 4.3 um at 77 K. The superlattice for the device was grown by molecular beam epitaxy while the planar device structure was achieved by Zinc diffusion process in a metal–organic chemical vapor deposition reactor. At 77 K, the peak responsivity and the corresponding quantum efficiency had the value of 1.42 A/W and 48% respectively at 3.7 um under -20 mV for the MWIR planar photodetector. At 77 K, the MWIR planar photodetector exhibits a dark current density of 2.0E5 A/cm^2 and the R0A value of ~3.0E2 Ohm cm^2 under -20 mV, which yielded a specific detectivity of 4.0E11 cm Hz^(1/2)/W at 3.7 um. At 150 K, the planar device showed a dark current density of 6.4E-5 A/cm^2 and a quantum efficiency of 49% at ~3.7 um under -20 mV, which yielded a specific detectivity of 2.0E11 cm Hz^(1/2)/W. [reprint (PDF)]
18.	Modeling of Type-II InAs/GaSb Superlattices Using Empirical Tight-Binding Method and Interface Engineering Y. Wei and M. Razeghi Physical Review B, 69 (8)-- February 15, 2004 ...[Visit Journal] We report the most recent work on the modeling of type-II InAs/GaSb superlattices using the empirical tight binding method in an sp3s* basis. After taking into account the antimony segregation in the InAs layers, the modeling accuracy of the band gap has been improved. Our calculations agree with our experimental results within a certain growth uncertainty. In addition, we introduce the concept of Ga_xIn_1-x type interface engineering in order to reduce the lattice mismatch between the superlattice and the GaSb (001) substrate to improve the overall superlattice material quality. [reprint (PDF)]
18.	Fabrication of 12 µm pixel-pitch 1280 × 1024 extended short wavelength infrared focal plane array using heterojunction type-II superlattice-based photodetector Arash Dehzangi , Abbas Haddadi, Romain Chevallier, Yiyun Zhang and Manijeh Razegh Semicond. Sci. Technol. 34, 03LT01-- February 4, 2019 ...[Visit Journal] We present an initial demonstration of a 1280 × 1024 extended short-wavelength infrared focal plane array (FPA) imager with 12μm pixel-pitch based on type–II InAs/AlSb/GaSb superlattice heterojunction photodetectors, with a novel bandstructure-engineered photo-generated carrier extractor as the window layer in the hetero structure to efﬁciently extract the photo-generated carriers. This heterostructure with a larger bandgap top window/contact layer leads to the device having lower dark current density compared to conventional pn junction devices. The large format FPA was fabricated with 12 μm pixel-pitch using a developed fabrication process. Test pixels fabricated separately exhibit 100% cut–off wavelengths of ∼2.22, ∼2.34μm, and ∼2.45μm at 150, 200K, and 300K. The test devices achieve saturated quantum efﬁciency values under zero bias of 54.3% and 68.4% at 150 and 300K, under back-side illumination and without any anti-reﬂection coating. At 150K, these photodetectors exhibit dark current density of 1.63 × 10⁻⁷ A·cm⁻² under −20mV applied bias providing a speciﬁc detectivity of 1.01 × 10¹¹ cm ·Hz^½/W at 1.9μm. [reprint (PDF)]
18.	Use of Yttria-Stabilised Zirconia Substrates for Zinc Oxide Mediated Epitaxial Lift-off of Superior Yttria-Stabilised Zirconia Thin Films D. J. Rogers, T. Maroutian, V. E. Sandana, P. Lecoeur, F. H. Teherani, P. Bove and M. Razeghi Proc. of SPIE Vol. 12887, Oxide-based Materials and Devices XV, 128870P 2024, San Francisco),doi: 10.1117/12.3023431 ...[Visit Journal] ZnO layers were grown on (100) and (111) oriented YSZ substrates by pulsed laser deposition (PLD). X-ray diffraction studies revealed growth of wurtzite ZnO with strong preferential (0002) orientation. The ZnO layer on YSZ (111) showed distinct Pendellosung fringes and a more pronounced c-axis orientation (rocking curve of 0.08°). Atomic force microscopy revealed RMS roughnesses of 0.7 and 2.2nm for the ZnO on the YSZ (111) and YSZ (100), respectively. YSZ was then grown on the ZnO buffered YSZ (111) substrate by PLD. XRD revealed that the YSZ overlayer grew with a strong preferential (111) orientation. The YSZ/ZnO/YSZ (111) top surface was temporary bonded to an Apiezon wax carrier and the sample was immersed in 0.1M HCl so as to preferentially etch/dissolve away the ZnO underlayer and release the YSZ from the substrate. XRD revealed only the characteristic (111) peak of YSZ after lift-off and thus confirmed both the dissolution of the ZnO and the preservation of the crystallographic integrity of the YSZ on the wax carrier. Optical and Atomic Force Microscopy revealed some buckling, roughening and cracking of the lifted YSZ, however. XRD suggested that this may have been due to compressive epitaxial strain release. [reprint (PDF)]
18.	Quantum Dot Infrared Photodetectors: Comparison Experiment and Theory H. Lim, W. Zhang, S. Tsao, T. Sills, J. Szafraniec, K. Mi, B. Movaghar, and M. Razeghi Physical Review B, 72-- August 17, 2005 ...[Visit Journal] We present data and calculations and examine the factors that determine the detectivities in self-assembled InAs and InGaAs based quantum dot infrared photodetectors (QDIPs). We investigate a class of devices that combine good wavelength selectivity with “high detectivity.” We study the factors that limit the temperature performance of quantum dot detectors. For this we develop a formalism to evaluate the optical absorption and the electron transport properties. We examine the performance limiting factors and compare theory with experimental data. We find that the notion of a phonon bottleneck does not apply to large-diameter lenslike quantum dots, which have many closely spaced energy levels. The observed strong decrease of responsivity with temperature is ultimately due to a rapid thermal cascade back into the ground states. High temperature performance is improved by engineering the excited state to be near the continuum. The good low temperature (77 K) performance in strongly bound QDIPs is shown to be due to the high gain and the low noise achievable in these micron size devices. [reprint (PDF)]
18.	Growth and Characterization of Very Long Wavelength Type-II Infrared Detectors H. Mohseni, A. Tahraoui, J. Wojkowski, M. Razeghi, W. Mitchel, and A. Saxler SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] We report on the growth and characterization of type-II IR detectors with a InAs/GaSb superlattice active layer in the 15-19 μm wavelength range. The material was grown by molecular beam epitaxy on semi-insulating GaAs substrates. The material was processed into photoconductive detectors using standard photolithography, dry etching, and metalization. The 50 percent cut-off wavelength of the detectors is about 15.5 μm with a responsivity of 90 mA/W at 80 K. The 90 percent-10 percent cut-off energy width of the responsivity is only 17 meV which is an indication of the uniformity of the superlattices. These are the best reported values for type-II superlattices grown on GaAs substrates. [reprint (PDF)]
18.	Ga₂O₃ Metal-oxide-semiconductor Field Effect Transistors on Sapphire Substrate by MOCVD Ji-Hyeon Park, Ryan McClintock and Manijeh Razeghi Semiconductor Science and Technology, Volume 34, Number 8-- June 26, 2019 ...[Visit Journal] Si-doped gallium oxide (Ga₂O₃) thin films were grown on a c-plane sapphire substrate by metalorganic chemical vapor deposition (MOCVD) and fabricated into metal oxide semiconductor field effect transistors (MOSFETs). The Ga₂O₃ MOSFETs exhibited effective gate modulation of the drain current with a complete channel pinch-off for VG < −25 V, and the three-terminal off-state breakdown voltage was 390 V. The device shows a very low gate leakage current (~50 pA/mm), which led to a high on/off ratio of ~10⁸. These transistor characteristics were stable from room temperature to 250 °C [reprint (PDF)]
18.	High-power, continuous-operation intersubband laser for wavelengths greater than 10 micron S. Slivken, A. Evans, W. Zhang and M. Razeghi Applied Physics Letters, Vol. 90, No. 15, p. 151115-1-- April 9, 2007 ...[Visit Journal] In this letter, high-power continuous-wave emission (>100 mW) and high temperature operation (358 K) at a wavelength of 10.6 µm is demonstrated using an individual diode laser. This wavelength is advantageous for many medium-power applications previously reserved for the carbon dioxide laser. Improved performance was accomplished using industry-standard InP-based materials and by careful attention to design, growth, and fabrication limitations specific to long-wave infrared semiconductor lasers. The main problem areas are explored with regard to laser performance, and general steps are outlined to minimize their impact. [reprint (PDF)]
18.	Two‐dimensional electron gas in a In0.53Ga0.47As‐InP heterojunction grown by metalorganic chemical vapor deposition Y. Guldner; J. P. Vieren; P. Voisin; M. Voos; M. Razeghi; M. A. Poisson Y. Guldner, J. P. Vieren, P. Voisin, M. Voos, M. Razeghi, M. A. Poisson; Two‐dimensional electron gas in a In0.53Ga0.47As‐InP heterojunction grown by metalorganic chemical vapor deposition. Appl. Phys. Lett. 15 May 1982; 40 (10): 877–879.-- April 15, 1982 ...[Visit Journal] We report, from Shubnikov-de Haas and cyclotron resonance experiments, the first observation of a two-dimensional, high-mobility electron gas in a selectively doped 1110.53 G~l.47 As-InP heterojunction grown by metalorganic chemical vapor deposition. Several parameters of the electronic system under consideration are determined. [reprint (PDF)]

Page 4 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)