Center for Quantum Devices - Most Downloaded Journal Articles

Page 30 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

10.	280 nm UV LEDs Grown on HVPE GaN Substrates A. Yasan, R. McClintock, K. Mayes, S.R. Darvish, P. Kung, M. Razeghi, and R.J. Molnar Opto-Electronics Review, 10 (4)-- January 1, 2002 ...[Visit Journal] We report on the enhancement of optical and electrical properties of 280 nm UV LEDs using low dislocation density HVPE-grown GaN substrate. Compared with the same structure grown on sapphire, these LEDs show ~30% reduction in current-voltage differential resistance, ~15% reduction in turn-on voltage, more than 200% increase in output power slope efficiency and saturation at higher currents. Lower density of defects due to higher material quality and better heat dissipation are believed to be the reason behind these improvements. [reprint (PDF)]
10.	High-speed free-space optical communications based on quantum cascade lasers and type-II superlattice detectors Stephen M. Johnson; Emily Dial; M. Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128814-- January 31, 2020 ...[Visit Journal] Free-space optical communications (FSOC) is a promising avenue for point-to-point, high-bandwidth, and high-security communication links. It has the potential to solve the “last mile” problem modern communication systems face, allowing for high-speed communication links without the expensive and expansive infrastructure required by fiber optic and wireless technologies 1 . Although commercial FSOC systems currently exist, due to their operation in the near infrared and short infrared ranges, they are necessarily limited by atmospheric absorption and scattering losses 2 . Mid-infrared (MWIR) wavelengths are desirable for free space communications systems because they have lower atmospheric scattering losses compared to near-infrared communication links. This leads to increased range and link uptimes. Since this portion of the EM spectrum is unlicensed, link establishment can be implemented quickly. Quantum cascade lasers (QCL) are ideal FSOC transmitters because their emission wavelength is adjustable to MWIR 3 . Compared to the typical VCSEL and laser diodes used in commercial NIR and SWIR FSOC systems, however, they require increased threshold and modulation currents 4 . Receivers based on type-II superlattice (T2SL) detectors are desired in FSOC for their low dark current, high temperature operation, and band gap tunable to MWIR 5. In this paper, we demonstrate the implementation of a high-speed FSOC system using a QCL and a T2SL detector. [reprint (PDF)]
10.	AlGaN-based deep-ultraviolet 320 x 256 focal plane array E. Cicek, Z. Vashaei, E.K. Huang, R. McClintock and M. Razeghi OSA Optics Letters, Vol. 37, No. 5, p. 896-898-- March 1, 2012 ...[Visit Journal] We report the synthesis, fabrication, and testing of a 320 × 256 focal plane array (FPA) of back-illuminated, solarblind, p-i-n, Al_xGa_1−xN–based detectors, fully realized within our research laboratory. We implemented a pulse atomic layer deposition technique for the metalorganic chemical vapor deposition growth of thick, high-quality, crack-free, high Al composition Al_xGa_1−xN layers. The FPA is hybridized to a matching ISC 9809 readout integrated circuit and operated in a SE-IR camera system. Solar-blind operation is observed throughout the array with peak detection occurring at wavelengths of 256 nm and lower, and falling off three orders of magnitude by ∼285 nm. By developing an opaque masking technology, the visible response of the ROIC is significantly reduced; thus the need for external filtering to achieve solar- and visible-blind operation is eliminated. This allows the FPA to achieve high external quantum efficiency (EQE); at 254 nm, average pixels showed unbiased peak responsivity of 75 mA∕W, which corresponds to an EQE of ∼37%. Finally, the uniformity of the FPA and imaging properties are investigated. [reprint (PDF)]
10.	Direct growth of thick AlN layers on nanopatterned Si substrates by cantilever epitaxy Ilkay Demir, Yoann Robin, Ryan McClintock, Sezai Elagoz, Konstantinos Zekentes, and Manijeh Razeghi Physica Status Solidi 214 (4), pp. 1770120-- April 4, 2017 ...[Visit Journal] The growth of thick, high quality, and low stress AlN films on Si substrates is highly desired for a number of applications like the development of micro and nano electromechanical system (MEMS and NEMS) technologies [1] and particularly for fabricating AlGaNbased UV LEDs [2–5]. UV LEDs are attractive as they are applied in many areas, such as biomedical instrumentations and dermatology, curing of industrial resins and inks, air purification, water sterilization, and many others [2, 3]. UV LEDs have been generally fabricated on AlN, GaN, Al₂O₃, or SiC substrates because of better lattice mismatching to AlGaN material systems. [reprint (PDF)]
9.	High-performance, continuous-wave operation of λ ~ 4.6 μm quantum-cascade lasers above room temperature J.S. Yu, S. Slivken, A. Evans and M. Razeghi IEEE Journal of Quantum Electronics, Vol. 44, No. 8, p. 747-754-- August 1, 2008 ...[Visit Journal] We report the high-performance continuous-wave (CW) operation of 10-μm-wide quantum-cascade lasers (QCLs) emitting at λ ~ 4.6 μm, based on the GaInAs–AlInAs material without regrowth, in epilayer-up and -down bonding configurations. The operational characteristics of QCLs such as the maximum average power, peak output power, CW output power, and maximum CW operating temperature are investigated, depending on cavity length. Also, important device parameters, i.e., the waveguide loss, the transparency current density, the modal gain, and the internal quantum efficiency, are calculated from length-dependent results. For a high-reflectivity (HR) coated 4-mm-long cavity with epilayer-up bonding, the highest maximum average output power of 633 mW is measured at 65% duty cycle, with 469 mW still observed at 100%. The laser exhibits the maximum wall-plug efficiencies of 8.6% and 3.1% at 298 K, in pulsed and CW operatons, respectively. From 298 to 393 K, the temperature dependent threshold current density in pulsed operation shows a high characteristic temperature of 200 K. The use of an epilayer-down bonding further improves the device performance. A CW output power of 685 mW at 288 K is achieved for the 4-micron-long cavity. At 298 K, the output power of 590 mW, threshold current density of 1.52 kA / cm2, and maximum wall-plug efficiency of 3.73% are obtained under CW mode, operating up to 363 K (90 °C). For HR coated 3-micron-long cavities, laser characteristics across the same processed wafer show a good uniformity across the area of 2 x 1 cm², giving similar output powers, threshold current densities, and emission wavelengths. The CW beam full-width at half-maximum of far-field patterns are 25 degree and 46 degree for the parallel and the perpendicular directions, respectively. [reprint (PDF)]
9.	Defects in Organometallic Vapor-Phase Epitaxy-Grown GaInP Layers Feng S.L., Bourgoin J.C., Omnes F., and Razeghi M. Applied Physics Letters 59 (8), p. 941-- May 28, 1991 ...[Visit Journal] Non-intentionally doped metalorganic vapor‐phase epitaxy Ga_1−x InxP layers, having an alloy composition (x = 0.49) corresponding to a lattice matched to GaAs, grown by metalorganic chemical vapor deposition, have been studied by capacitance‐voltage and deep-level transient spectroscopy techniques. They are found to exhibit a free‐carrier concentration at room temperature of the order of 10¹⁵ cm⁻³. Two electron traps have been detected. The first one, at 75 meV below the conduction band, is in small concentration (∼10¹³ cm⁻³) while the other, at about 0.9 eV and emitting electrons above room temperature, has a concentration in the range 10¹⁴–10¹⁵ cm⁻³. [reprint (PDF)]
9.	Observation of inversion layers at AlN-Si interfaces fabricated by metal organic chemical vapour deposition X. Zhang, D. Walker, A. Saxler, P. Kung, J. Xu, and M. Razeghi IEEE Electronic Letters 32 (17)-- August 15, 1996 ...[Visit Journal] AlN has been grown on Si(111) substrates by metal organic chemical vapour deposition. The formation of an inversion layer on n-type Si(111) has been clearly observed by capacitance-voltage measurements at high and low frequencies. The interface trap level density was calculated to be in the range of 1011 cm–2eV–1 from capacitance-voltage and conductance-voltage measurements. [reprint (PDF)]
9.	Overview of Antimonide Based III-V Semiconductor Epitaxial Layers and their Applications at the Center for Quantum Devices M. Razeghi The European Physical Journal-Applied Physics, Vol. 23-- September 15, 2003 ...[Visit Journal] The properties of Sb-based III-V semiconductor compounds for optoelectronic applications in the mid-wavelength infrared (MWIR) and long-wavelength infrared (LWIR) range were reviewed. The growths of the Sb-based binary, ternary and quaternary were studied by molecular beam epitaxy (MBE) and metalorganic chemical vapor deposition (MOCVD). The structural, optical and electrical characterizations were carried out. Focal plane array, photoconductors and photodiodes were fabricated for the MWIR and LWIR range. Doublehetero structure (DH), multi-quantum well (MQW) and strained superlattice (SSL) lasers in the 3-5 μm range were fabricated. InAs-GaSb type-II superlattices were designed, grown and fabricated into photodetectors for the MWIR and LWIR range. [reprint (PDF)]
9.	High operability 1024 x 1024 long wavelength infrared focal plane array base on Type-II InAs/GaSb superlattice A. Haddadi, S.R. Darvish, G. Chen, A.M. Hoang, B.M. Nguyen and M. Razeghi AIP Conference Proceedings, Vol. 1416, p. 56-58_NGS15 Conf_Blacksburg, VA_Aug 1-5, 2011-- December 31, 2011 ...[Visit Journal] Fabrication and characterization of a high performance 1024×1024 long wavelength infrared type‐II superlattice focal plane array are described. The FPA performs imaging at a continous rate of 15.00 frames/sec. Each pixel has pitch of 18μm with a fill factor of 71.31%. It demonstrates excellent operability of 95.8% and 97.4% at 81 and 68K operation temperature. The external quantum efficiency is ∼81% without any antireflective coating. Using F∕2 optics and an integration time of 0.13ms, the FPA exhibits an NEDT as low as 27 and 19mK at operating temperatures of 81 and 68K respectively. [reprint (PDF)]
9.	EPR Investigations of a Structural Phase Change in Lead Phosphate M. RAZEG M. RAZEGHI: EPR Investigations of a Structural Phase Change, phys. stat. sol. (b) 108, 175 (1981)-- April 10, 2010 ...[Visit Journal] The temperature dependence of the EPR line width of the Mn2+ and Gd3+ in Pb,(PO,), is investigated from -270 to 500 "C. At the first-order ferroelastic transition point (180 "C), an abrupt change in the fine-structure splitting as well as in the resonance line width is observed. Various contributions to fine structure D and E parameters of Mn2+ and Gd3+ are computed, using a point-multipole model. For temperatures near to Tc the correlation time of the fluctuations is estimated to be greater than Die Temperaturabhangigkeit der EPR-Linienbreite von Mn2+,'und Gd3+ in Pb,(PO,), wird zwischen -270 und 500 "C untersucht. Am ferroelastischen vbergangspunkt erster Ordnung (180 "C) wird eine abrupte Anderung der Feinstrukturaufspaltung sowie der Linienbreite der Resonanzlinien beobachtet. Verschiedene Beitrage zu den Feinstrukturparametern D und E von Mn2+ und Gd3+ werden mittels eines Punkt-Multipol-Modells berechnet. Fur Temperaturen in der Nahe von T, wird die Korrelationszeit der Fluktuationen eu groI3er als s. s bestimmt. [reprint (PDF)]
9.	Surface leakage current reduction in long wavelength infrared type-II InAs/GaSb superlattice photodiodes S. Bogdanov, B.M. Nguyen, A.M. Hoang, and M. Razeghi Applied Physics Letters, Vol. 98, No. 18, p. 183501-1-- May 2, 2011 ...[Visit Journal] Dielectric passivation of long wavelength infrared Type-II InAs/GaSb superlattice photodetectors with different active region doping profiles has been studied. SiO₂ passivation was shown to be efficient as long as it was not put in direct contact with the highly doped superlattice. A hybrid graded doping profile combined with the shallow etch technique reduced the surface leakage current in SiO₂ passivated devices by up to two orders of magnitude compared to the usual design. As a result, at 77 K the SiO(2) passivated devices with 10.5 μm cutoff wavelength exhibit an R₀A of 120 Ω·cm², R_maxA of 6000 Ω·cm², and a dark current level of 3.5×10⁻⁵ A·cm⁻² at −50 mV bias. [reprint (PDF)]
9.	Structural, Optical, Electrical and Morphological Study of Transparent p-NiO/n-ZnO Heterojunctions Grown by PLD V. E. Sandana, D. J. Rogers, F. Hosseini Teherani, P. Bove, N. Ben Sedrine, M. R. Correia, T. Monteiro, R. McClintock, and M. Razeghi Proc. SPIE 9364, Oxide-based Materials and Devices VI, 93641O-- March 24, 2015 ...[Visit Journal] NiO/ZnO heterostructures were fabricated on FTO/glass and bulk hydrothermal ZnO substrates by pulsed laser deposition. X-Ray diffraction and Room Temperature (RT) Raman studies were consistent with the formation of (0002) oriented wurtzite ZnO and (111) oriented fcc NiO. RT optical transmission studies revealed bandgap energy values of ~3.70 eV and ~3.30 eV for NiO and ZnO, respectively and more than 80% transmission for the whole ZnO/NiO/FTO/glass stack over the majority of the visible spectrum. Lateral p-n heterojunction mesas (~6mm x 6mm) were fabricated using a shadow mask during PLD growth. n-n and p-p measurements showed that Ti/Au contacting gave an Ohmic reponse for the NiO, ZnO and FTO. Both heterojunctions had rectifying I/V characteristics. The junction on FTO/glass gave forward bias currents (243mA at +10V) that were over 5 orders of magnitude higher than those for the junction formed on bulk ZnO. At ~ 10^-7 A (for 10V of reverse bias) the heterojunction leakage current was approximately two orders of magnitude lower on the bulk ZnO substrate than on FTO. Overall, the lateral p-NiO/n-ZnO/FTO/glass device proved far superior to that formed by growing p-NiO directly on the bulk n-ZnO substrate and gave a combination of electrical performance and visible wavelength transparency that could predispose it for use in various third generation transparent electronics applications. [reprint (PDF)]
9.	Optical Absorption and Photoresponse in fully Quaternary p-type Quantum Well Detectors J. Hoff, C. Jelen, S. Slivken, G.J. Brown, and M. Razeghi SPIE Photonics West '96 Photodetectors: Materials and Devices; Proceedings 2685-- January 27, 1996 ...[Visit Journal] Acceptor doped, non-strained aluminum-free Quantum Well Intersubband Photodetectors lattice matched to GaAs with Ga_0.79In_0.21As_0.59P_0.41 wells and Ga_0.62In_0.38As_0.22P_0.78 barriers have been demonstrated on semi-insulating GaAs substrates. These devices which operate at normal incidence demonstrate a unique spectral response which extends from approximately 2 μm up to 10 μm. To explain such a broad spectral shape, a detailed theoretical analysis based on the 8 x 8 Kane Hamiltonian was necessary to probe all aspect of optical absorption. The results of this analysis revealed that spectral shape results from the influence of the Spin Split-off band on the band structure and the optical matrix. [reprint (PDF)]
9.	Use of ZnO thin films as sacrifical templates for metal organic vapor phase epitaxy and chemical lift-off of GaN D.J. Rogers, F. Hosseini Teherani, A. Ougazzaden, S. Gautier, L. Divay, A. Lusson, O. Durand, F. Wyczisk, G. Garry, T. Monteiro, M.R. Correira, M. Peres, A. Neves, D. McGrouther, J.N. Chapman, and M. Razeghi Applied Physics Letters, Vol. 91, No. 7, p. 071120-1-- August 13, 2007 ...[Visit Journal] Continued development of GaN-based light emitting diodes is being hampered by constraints imposed by current non-native substrates. ZnO is a promising alternative substrate but it decomposes under the conditions used in conventional GaN metal organic vapor phase epitaxy (MOVPE). In this work, GaN was grown on ZnO/c-Al₂O₃ using low temperature/pressure MOVPE with N₂ as a carrier and dimethylhydrazine as a N source. Characterization confirmed the epitaxial growth of GaN. The GaN was lifted-off the c-Al₂O₃ by chemically etching away the ZnO underlayer. This approach opens up the way for bonding of the GaN onto a support of choice. [reprint (PDF)]
9.	Surface Emitting, Tunable, Mid-Infrared Laser with High Output Power and Stable Output Beam Steven Slivken, Donghai Wu & Manijeh Razeghi Scientific Reports volume 9, Article number: 549-- January 24, 2019 ...[Visit Journal] A reflective outcoupler is demonstrated which can allow for stable surface emission from a quantum cascade laser and has potential for cost-effective wafer-scale manufacturing. This outcoupler is integrated with an amplified, electrically tunable laser architecture to demonstrate high power surface emission at a wavelength near 4.9 μm. Single mode peak power up to 6.7 W is demonstrated with >6 W available over a 90 cm⁻¹ (215 nm) spectral range. A high quality output beam is realized with a simple, single-layer, anti-reflective coating. The beam shape and profile are shown to be independent of wavelength. [reprint (PDF)]
9.	Roadmap of Semiconductor Infrared Lasers and Detectors for the 21st Century M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] Since the first discovery, semiconductor infrared lasers and detectors have found many various applications in military, communications, medical, and industry sections. In this paper, the current status of semiconductor infrared lasers and detectors will be reviewed. Advantages and disadvantages of different methods and techniques is discussed later. Some basic physical limitations of current technology are studied and the direction to overcome these problems will be suggested. [reprint (PDF)]
9.	InGaAlAs/InP Quantum Well Infrared Photodetectors for 8-20 μm Wavelengths C. Jelen, S. Slivken, V. Guzman, M. Razeghi, and G. Brown IEEE Journal of Quantum Electronics 34 (10)-- October 1, 1998 ...[Visit Journal] We demonstrate the first long-wavelength quantum-well infrared photodetectors using the lattice-matched n-doped InGaAlAs-InP materials system. Samples with AlAs mole fractions of 0.0, 0.1, and 0.15 result in cutoff wavelengths of 8.5, 13.3, and 19.4 mu m, respectively. A 45 degrees facet coupled illumination. responsivity of R = 0.37 A/W and detectivity of D-lambda* = 3 x 10(8) cm .root Hz . W-1 at T = K, for a cutoff wavelength lambda(c) = 13.3 mu m have been achieved. Based on the measured intersubband photoresponse wavelength, a null conduction band offset is expected for In0.52Ga0.21Al0.27As-InP heterojunctions. [reprint (PDF)]
9.	High performance Zn-diffused planar mid-wavelength infrared type-II InAs/InAs_1-xSb_x superlattice photodetector by MOCVD Donghai Wu, Arash Dehzangi, Jiakai Li, and Manijeh Razeghi Appl. Phys. Lett. 116, 161108-- April 21, 2020 ...[Visit Journal] We report a Zn-diffused planar mid-wavelength infrared photodetector based on type-II InAs/InAs_1-xSb_x superlattices. Both the superlattice growth and Zn diffusion were performed in a metal-organic chemical vapor deposition system. At 77K, the photodetector exhibits a peak responsivity of 0.70A/W at 3.65λ, corresponding to a quantum efﬁciency of 24% at zero bias without anti-reﬂection coating, with a 50% cutoff wavelength of 4.28λ. With an R₀A value of 3.2x10⁵ Ω·cm² and a dark current density of 9.6x10^-8 A/cm² bias of -20mV at 77K, the photodetector exhibits a speciﬁc detectivity of 2.9x10¹²cm·Hz^½/W. At 150K, the photodetector exhibits a dark current density of 9.1x10^-6 A/cm² and a quantum efﬁciency of 25%, resulting in a detectivity of 3.4x10¹¹cm·Hz/W. [reprint (PDF)]
9.	UVC communication with (Al)Ga₂O₃ photodetectors & a Q-switched solid-state laser including demonstration of a Rayleigh-scattering-based NLOS link D. Rogers, V. Sandana, M. Chamberlin, F. Teherani, S. Prein, and M. Razeghi OPTO (SPIE, 2026), Vol. PC13897 ...[Visit Journal] This work reports solar-blind ultraviolet-C (UVC) optical communication links implemented using epitaxial (Al)Ga₂O₃ metal–semiconductor–metal photodetectors paired with a wavelength-matched, passively Q-switched 213 nm solid-state laser. The photodetectors, originally developed for space-based monitoring of the Herzberg continuum, combine high solar blindness, femtoampere-level dark noise, and robust operation under demanding conditions. Both line-of-sight (LOS) and non-line-of-sight (NLOS) communication geometries are investigated. The detectors exhibit a sharp UVC responsivity peak near 215 nm, a solar-rejection ratio exceeding 2 × 10⁴, and low dark signals enabled by bandgap engineering via aluminum alloying. These characteristics allow LOS communication at distances up to 110 m with sub-20 ms response times, as well as detection of NLOS optical signals at the femtowatt level under near-zero-bias (photovoltaic) operating conditions. For off-axis angles of 15°, the measured NLOS photocurrents are in quantitative agreement with single-scatter Rayleigh predictions, while signals at 45° fall below the detection threshold, consistent with reduced scattering volume and angular dependence. To the authors’ knowledge, this constitutes the first experimental demonstration of Rayleigh-scattering-based NLOS UVC communication using Ga₂O₃ photodetectors, extending prior Ga₂O₃ communication studies beyond pure LOS configurations. The results highlight the potential of Ga₂O₃-based sensors and compact solid-state UVC sources for alignment-tolerant and covert optical communication links in both terrestrial and space -relevant environments. [reprint (PDF)]
9.	ZnO Thin Films & Nanostructures for Emerging Optoelectronic Applications D.J. Rogers, F. Hosseini Teherani, V.E. Sandana, and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7605, p. 76050K-1-- January 27, 2010 ...[Visit Journal] ZnO-based thin films and nanostructures grown by PLD for various emerging optoelectronic applications. AZO thin films are currently displacing ITO for many TCO applications due to recent improvements in attainable AZO conductivity combined with processing, cost and toxicity advantages. Advances in the channel mobilities and Id on/off ratios in ZnO-based TTFTs have opened up the potential for use as a replacement for a-Si in AM-OLED and AM-LCD screens. Angular-dependent specular reflection measurements of self-forming, moth-eye-like, nanostructure arrays grown by PLD were seen to have <0.5% reflectivity over the whole visible spectrum for angles of incidence between 10 and 60 degrees. Such nanostructures may be useful for applications such as AR coatings on solar cells. Compliant ZnO layers on mismatched/amorphous substrates were shown to have potential for MOVPE regrowth of GaN. This approach could be used as a means to facilitate lift-off of GaN-based LEDs from insulating sapphire substrates and could allow the growth of InGaN-based solar cells on cheap substrates. The green gap in InGaN-based LEDs was combated by substituting low Ts PLD n-ZnO for MOCVD n-GaN in inverted hybrid heterojunctions. This approach maintained the integrity of the InGaN MQWs and gave LEDs with green emission at just over 510 nm. Hybrid n-ZnO/p-GaN heterojunctions were also seen to have the potential for UV (375 nm) EL, characteristic of ZnO NBE emission. This suggests that there was significant hole injection into the ZnO and that such LEDs could profit from the relatively high exciton binding energy of ZnO. [reprint (PDF)]
9.	Delta-doping optimization for high qualityp-type GaN C. Bayram, J.L. Pau, R. McClintock and M. Razeghi Journal of Applied Physics, Vol. 104, No. 8-- October 15, 2008 ...[Visit Journal] Delta-doping is studied in order to achieve high quality p-type GaN. Atomic force microscopy, x-ray diffraction, photoluminescence, and Hall measurements are performed on the samples to optimize the delta-doping characteristics. The effect of annealing on the electrical, optical, and structural quality is also investigated for different delta-doping parameters. Optimized pulsing conditions result in layers with hole concentrations near 10¹⁸ cm⁻³ and superior crystal quality compared to conventional p-GaN. This material improvement is achieved thanks to the reduction in the Mg activation energy and self-compensation effects in delta-doped p-GaN. [reprint (PDF)]
9.	The Molecular Beam Epitaxial Growth of InSb on (111) GaAs E. Michel, J. Kim, J. Xu, S. Javadpour, I. Ferguson, and M. Razeghi Applied Physics Letters 69 (2)-- July 8, 1996 ...[Visit Journal] The molecular beam epitaxial growth of InSb on (111)B GaAs has been investigated. It was found that for a given Sb/In ratio, a higher growth temperature was required for the growth of InSb on (111)B GaAs compared to that on (001) GaAs. This difference has been attributed to the bonding characteristics of the (111)B and (001) surface. Once growth had been optimized, it was found that the material characteristics of (111)B InSb were almost identical to that of (001) InSb, i.e., independent of orientation. For example, the x-ray full width at half-maximum and 300 K mobility had the same absolute values for (111) InSb and (001)InSb and followed the same dependence with the sample thickness. Te was found to be a well-behaved n-type dopant for (111)B InSb. [reprint (PDF)]
9.	High Quantum Efficiency Solar-Blind Photodetectors R. McClintock, A. Yasan, K. Mayes, D. Shiell, S. Darvish, P. Kung and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 434-- January 25, 2004 ...[Visit Journal] We report AlGaN-based back-illuminated solar-blind p-i-n photodetectors with a record peak responsivity of 150 mA/W at 280 nm, corresponding to a high external quantum efficiency of 68%, increasing to 74% under 5 volts reverse bias. Through optimization of the p-AlGaN layer, we were able to remove the out-of-band negative photoresponse originating from the Schottky-like p-type metal contact, and hence significantly improve the degree of solar-blindness [reprint (PDF)]
9.	High-power InGaAsP/GaAs 0.8 μm laser diodes and peculiarities of operational characteristics J. Diaz, I. Eliashevich, X. He, H. Yi, L. Wang, E. Kolev, D. Garbuzov, and M. Razeghi Applied Physics Letters 65 (8)-- August 22, 1994 ...[Visit Journal] High-power operation of 3 W in pulse mode, 750 mW in quasi-continuous wave and 650 mW in continuous wave per uncoated facet from 100 μm aperture has been demonstrated for 1 mm long cavity InGaAsP/GaAs 808 nm laser diodes prepared by low-pressure metalorganic chemical vapor deposition. Threshold current density of 300 A/cm², differential efficiency of 1.1 W/A, T₀=155 °C, transverse beam divergence of 27°, and less than 2 nm linewidth at 808 nm have been measured. No degradation has been observed after 1000 h of operation in a quasi-continuous wave regime. [reprint (PDF)]
9.	Optimizing facet coating of quantum cascade lasers for low power consumption Y. Bai, S.R. Darvish, N. Bandyopadhyay, S. Slivken and M. Razeghi Journal of Applied Physics, Vol. 109, No. 5, p. 053103-1-- March 1, 2011 ...[Visit Journal] Typical high power consumption (∼10 W) of mid-infrared quantum cascade lasers (QCLs) has been a serious limitation for applications in battery powered systems. A partial high-reflection (PHR) coating technique is introduced for power downscaling with shorter cavity lengths. The PHR coating consists of a double layer dielectric of SiO₂ and Ge. With this technique, a 4.6 μm QCL with an ultra low threshold power consumption of less than a watt (0.83 W) is demonstrated in room temperature continuous wave operation. At 25°C, the maximum output power and wall plug efficiency are 192 mW and 8.6%, respectively. [reprint (PDF)]

Page 30 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)