Center for Quantum Devices - Most Downloaded Journal Articles

Page 3 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

19.	Characterization and Analysis of Single-Mode High-Power CW Quantum-Cascade Laser W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A. Evans, J.S. Yu, S.R. Darvish, S. Slivken, and M. Razeghi Journal of Applied Physics 98-- October 15, 2005 ...[Visit Journal] We measured and modeled the performance characteristics of a distributed-feedback quantum-cascade laser exhibiting high-power continuous-wave (CW) operation in a single spectral mode at λ~4.8 µm and temperatures up to 333 K. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single mode at all currents and temperatures tested. CW output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. The slope efficiency and subthreshold amplified spontaneous emission spectra are shown to be consistent with a coupling coefficient of no more than κL ~ 4–5, which is substantially lower than the estimate of 9 based on the nominal grating fabrication parameters. [reprint (PDF)]
19.	Growth and characterization of InAs/GaSb Type-II superlattices for long-wavelength infrared detectors H. Mohseni, E. Michel, M. Razeghi, W. Mitchel, and G. Brown SPIE Conference, San Jose, CA, -- January 28, 1998 ...[Visit Journal] We report the molecular beam epitaxial growth and characterization of InAs/GaSb superlattices grown on semi- insulating GaAs substrate for long wavelength IR detectors. Photoconductive detectors fabricated from the superlattices showed 80% cut-off at 11.6 μm and peak responsivity of 6.5 V/W with Johnson noise limited detectivity of 2.36 x 10⁹ cm·Hz^½/W at 10.7 μm at 78 K. The responsivity decreases at higher temperatures with a T^-2 behavior rather than exponential decay, and at room temperature the responsivity is about 660 mV/W at 11 μm. Lower Auger recombination rate in this system provides comparable detectivity to the best HgCdTe detectors at 300K. Higher uniformity over large areas, simpler growth and the possibility of having read-out circuits in the same GaAs chip are the advantages of this system over HgCdTe detectors for near room temperature operation. [reprint (PDF)]
19.	Very Long Wavelength GaAs/GaInP Quantum Well Infrared Photodetectors C. Jelen, S. Slivken, G.J. Brown, and M. Razeghi SPIE Conference, San Jose, CA, -- February 12, 1997 ...[Visit Journal] We demonstrate long wavelength quantum well infrared photodetectors with GaAs quantum wells and GaInP barriers grown using gas-source molecular beam epitaxy. Wafers were grown with varying well widths. The optimum well width was 75 angstrom, which resulted in a detection peak at 13 μm and a cutoff wavelength of 15 μm. Dark current measurements of the samples with 15 μm cutoff wavelength show low dark current densities. The dark current characteristics have been investigated as a function of temperature and electron density in the well and compared to a model which takes into account thermionic emission and thermally assisted tunneling. The model is used to extract a saturation velocity of 1.5 x 10⁵ cm/s for electrons. The photoelectron lifetime before recapture has been deduced from this carrier velocity and photoconductive gain measurements. The lifetime is found to be approximately 5 ps. Preliminary focal plane array imaging is demonstrated. [reprint (PDF)]
19.	High-Performance Type-II InAs/GaSb Superlattice Photodiodes with Cutoff Wavelength Around 7 µm Y. Wei, A. Hood, H. Yau, V. Yazdanpanah, M. Razeghi, M.Z. Tidrow and V. Nathan Applied Physics Letters, 86 (9)-- February 28, 2005 ...[Visit Journal] We report the most recent result in the area of type-II InAs/GaSb superlattice photodiodes that have a cutoff wavelength around 7 µm at 77 K. Superlattice with a period of 40 Å lattice matched to GaSb was realized using Ga_xIn_1–x type interface engineering technique. Compared with significantly longer period superlattices, we have reduced the dark current density under reverse bias dramatically. For a 3 µm thick structure, using sulfide-based passivation, the dark current density reached 2.6×10^–5 A/cm² at –3 V reverse bias at 77 K. At this temperature the photodiodes have R₀A of 9300 Ω·cm² and a thermally limited zero bias detectivity of 1×10¹² cm·Hz^½/W. The 90%–10% cutoff energy width was only 16.5 meV. The devices did not show significant dark current change at 77 K after three months storage in the atmosphere. [reprint (PDF)]
19.	Demonstration of type-II superlattice MWIR minority carrier unipolar imager for high operation temperature application Guanxi Chen, Abbas Haddadi, Anh-Minh Hoang, Romain Chevallier, and Manijeh Razeghi Optics Letters Vol. 40, Iss. 1, pp. 29–32-- December 18, 2014 ...[Visit Journal] An InAs/GaSb type-II superlattice-based mid-wavelength infrared (MWIR) 320×256 unipolar focal plane array (FPA) using pMp architecture exhibited excellent infrared image from 81 to 150 K and ∼98% operability, which illustrated the possibility for high operation temperature application. At 150 K and −50 mV operation bias, the 27 μm pixels exhibited dark current density to be 1.2×10⁻⁵ A/cm², with 50% cutoff wavelength of 4.9 μm, quantum efficiency of 67% at peak responsivity (4.6 μm), and specific detectivity of 1.2×10¹² Jones. At 90 K and below, the 27 μm pixels exhibited system limited dark current density, which is below 1×10⁻⁹ A/cm², and specific detectivity of 1.5×10¹⁴ Jones. From 81 to 100 K, the FPA showed ∼11 mK NEDT by using F/2.3 optics and a 9.69 ms integration time. [reprint (PDF)]
19.	Lateral epitaxial overgrowth of GaN films on sapphire and silicon substrates P. Kung, D. Walker, M. Hamilton, J. Diaz, and M. Razeghi Applied Physics Letters 74 (4)-- January 25, 1999 ...[Visit Journal] We report the lateral epitaxial overgrowth of GaN films on (00.1) Al₂O₃ and (111) Si substrates by metalorganic chemical vapor deposition. The lateral epitaxial overgrowth on Si substrates was possible after achieving quasi-monocrystalline GaN template films on (111) Si substrates. X-ray diffraction, photoluminescence, scanning electron microscopy, and atomic force microscopy were used to assess the quality of the lateral epitaxial overgrown films. Lateral growth rates more than five times as high as vertical growth rates were achieved for both lateral epitaxial overgrowths of GaN on sapphire and silicon substrates. [reprint (PDF)]
19.	Temperature dependence of the quantized Hall effect H. P. Wei, A. M. Chang, and D. C. Tsui M. Razeghi Phys. Rev. B 32, 7016(R) 1985-- November 15, 1985 ...[Visit Journal] We reported detailed measurements of the temperature dependence of the quantized Hall effect from 4.2 to 50 K in the i=2 plateau region in InGaAs-InP. We deduce from the data that there is a significant density of localized states between the two Landau levels, with a value of ∼1×1010 cm−2 meV−1 at the middle of the mobility gap. We also found that the correlations between 𝜎xx and 𝜎xy show the trend predicted by the recent two-parameter scaling theory of localization in quantized Hall effect. [reprint (PDF)]
19.	Reliable High-Power Uncoated Al-free InGaAsP/GaAs Lasers for Cost-Sensitive Optical Communication and Processing Applications M. Razeghi SPIE Conference, Dallas, TX, -- November 4, 1997 ...[Visit Journal] Unlike InP-based systems for long-distance communication applications, GaAs-based optoelectronic systems mostly for local-area network, optical interconnection or optical computing are very cost-sensitive because often these optoelectronic devices constitute most of the cost for these applications and fewer users share the cost. Thus besides technical issues, the processing cost should be addressed in the selection of materials and fabrication methods. We discuss a number of major advantages of Al-free InGaAsP/GaAs lasers for these applications, such as not coating- requirement, low cost, high long-term reliability, high performance. We discuss recent preliminary results of Al- free lasers as a first step toward these optoelectronic applications. [reprint (PDF)]
19.	Demonstration of Zn-Diffused Planar Long-Wavelength Infrared Photodetector Based on Type-II Superlattice Grown by MBE Rajendra K. Saroj, Van Hoang Nguyen, Steven Slivken, Gail J. Brown and Manijeh Razeghi IEEE Journal of Quantum Electronics ...[Visit Journal] We report on a planar long-wavelength infrared photodetector based on InAs/InAs1−xSbx type-II superlattice with zinc diffusion. The superlattice structures were grown by molecular beam epitaxy, followed by a post-growth Zinc diffusion process in a metal-organic chemical vapor deposition reactor. The planar photodetectors showed a peak responsivity of 2.18 A/W, under an applied bias of −20 mV, with a corresponding quantum efficiency of 44.5%, without any anti-reflection coating, and had a 100% cut-off wavelength of 8.5 μm at 77 K temperature. These photodetectors exhibit a specific peak detectivity of 3.0×10^12 cm.Hz^1/2/W, with a dark current density of 1.5 × 10−5 A/cm2 and the differential-resistance-area product of ∼8.6 × 10−1 Ω.cm2, under an applied bias of −20 mV at 77 K. A comparative study between the planar and conventional mesa isolated photodetectors was also carried out. [reprint (PDF)]
19.	Type-II superlattice photodetectors for MWIR to VLWIR focal plane arrays M. Razeghi, Y. Wei, A. Hood, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E. Michel and R. McClintock SPIE Infrared Technology and Applications Conference, April 17-21, 2006, Orlando, FL Proceedings – Infrared Technology and Applications XXXII, Vol. 6206, p. 62060N-1-- April 21, 2006 ...[Visit Journal] Results obtained on GaSb/InAs Type-II superlattices have shown performance comparable to HgCdTe detectors, with the promise of higher performance due to reduced Auger recombination and dark current through improvements in device design and material quality. In this paper, we discuss advancements in Type-II IR sensors that cover the 3 to > 30 µm wavelength range. Specific topics covered will be device design and modeling using the Empirical Tight Binding Method (ETBM), material growth and characterization, device fabrication and testing, as well as focal plane array processing and imaging. Imaging has been demonstrated at room temperature for the first time with a 5 µm cutoff wavelength 256×256 focal plane array. [reprint (PDF)]
19.	Investigation of impurities in type-II InAs/GaSb superlattices via capacitance-voltage measurement G. Chen, A. M. Hoang, S. Bogdanov, A. Haddadi, P. R. Bijjam, B.-M. Nguyen, and M. Razeghi Applied Physics Letters 103, 033512 (2013)-- July 17, 2013 ...[Visit Journal] Capacitance-voltage measurement was utilized to characterize impurities in the non-intentionally doped region of Type-II InAs/GaSb superlattice p-i-n photodiodes. Ionized carrier concentration versus temperature dependence revealed the presence of a kind of defects with activation energy below 6 meV and a total concentration of low 10¹⁵ cm⁻³. Correlation between defect characteristics and superlattice designs was studied. The defects exhibited a p-type behavior with decreasing activation energy as the InAs thickness increased from 7 to 11 monolayers, while maintaining the GaSb thickness of 7 monolayers. With 13 monolayers of InAs, the superlattice became n-type and the activation energy deviated from the p-type trend. [reprint (PDF)]
19.	High Power Mid-Infrared Quantum Cascade Lasers Grown on GaAs Steven Slivken and Manijeh Razeghi Photonics 2022, 9(4), 231 (COVER ARTICLE) ...[Visit Journal] The motivation behind this work is to show that InP-based intersubband lasers with high power can be realized on substrates with significant lattice mismatch. This is a primary concern for the integration of mid-infrared active optoelectronic devices on low-cost photonic platforms, such as Si. As evidence, an InP-based mid-infrared quantum cascade laser structure was grown on a GaAs substrate, which has a large (4%) lattice mismatch with respect to InP. Prior to laser core growth, a metamorphic buffer layer of InP was grown directly on a GaAs substrate to adjust the lattice constant. Wafer characterization data are given to establish general material characteristics. A simple fabrication procedure leads to lasers with high peak power (>14 W) at room temperature. These results are extremely promising for direct quantum cascade laser growth on Si substrates. [reprint (PDF)]
19.	Polarity inversion of Type-II InAs/GaSb superlattice photodiodes B.M. Nguyen, D. Hoffman, P.Y. Delaunay, M. Razeghi and V. Nathan Applied Physics Letters, Vol. 91, No. 10, p. 103503-1-- September 3, 2007 ...[Visit Journal] The authors demonstrated the realization of p-on-n Type-II InAs/GaSb superlattice photodiodes. Growth condition for high quality InAsSb layer lattice matched to GaSb was established for the use of an effective n-contact layer. By studying the effect of various GaSb capping layer thicknesses on the optical and electrical performances, an optimized thickness of 160 nm was determined. In comparison to as grown n-on-p superlattice photodiodes, this inverted design of p on n has shown similar quality. Finally, by analyzing Fabry-Perot interference fringes in the front side illuminated spectral measurement, the refractive index of the superlattice was determined to be approximately 3.8. [reprint (PDF)]
19.	High-performance short-wavelength infrared photodetectors based on type-II InAs/InAs_1-xSb_x/AlAs_1-xSb_x superlattices M. Razeghi, A. Haddadi, X. V. Suo, S. Adhikary, P. Dianat, R. Chevallier, A. M. Hoang, A. Dehzangi Proc. SPIE 9819, Infrared Technology and Applications XLII, 98190A -- May 20, 2016 ...[Visit Journal] We present a high-performance short-wavelength infrared n-i-p photodiode, whose structure is based on type-II superlattices with InAs/InAs_1-xSb_x/AlAs_1-xSb_x on GaSb substrate. At room temperature (300K) with front-side illumination, the device shows the peak responsivity of 0.47 A/W at 1.6mm, corresponding to 37% quantum efficiency at zero bias. At 300K, the device has a 50% cut-off wavelength of ~1.8mm. For −50mV applied bias at 300 K the photodetector has dark current density of 9.6x10^-5 A/cm² and RxA of 285 Ω•cm², and it revealed a detectivity of 6.45x10¹⁰ cm•Hz^½/W. Dark current density reached to 1.3x10^-8 A/cm² at 200 K, with 36% quantum efficiency which leads to the detectivity value of 5.66x10¹² cm•Hz^½/W. [reprint (PDF)]
19.	High power, continuous wave, room temperature operation of λ ~ 3.4 μm and λ ~ 3.55 μm InP-based quantum cascade lasers N. Bandyopadhyay, S. Slivken, Y. Bai and M. Razeghi Applied Physics Letters, Vol. 100, No. 21, p. 212104-1-- May 21, 2012 ...[Visit Journal] We report two highly strain-balanced InP-based AlInAs/GaInAs quantum cascade lasers emitting near 3.39 and 3.56 . A pulsed threshold current density of only 1.1 kA/cm² has been achieved at room temperature for both lasers with characteristic temperatures (T₀) of 166 K and 152 K, respectively. The slope efficiency is also relatively temperature insensitive with characteristic temperatures (T₁) of 116 K and 191 K, respectively. Continuous wave powers of 504 mW and 576 mW are obtained at room temperature, respectively. This was accomplished without buried ridge processing. [reprint (PDF)]
19.	Advances in antimonide-based Type-II superlattices for infrared detection and imaging at center for quantum devices M. Razeghi, A. Haddadi, A.M. Hoang, E.K. Huang, G. Chen, S. Bogdanov, S.R. Darvish, F. Callewaert, R. McClintock Infrared Physics & Technology, Volume 59, Pages 41-52 (2013)-- July 1, 2013 ...[Visit Journal] Type-II InAs/GaSb superlattices (T2SLs), a system of multi-interacting quantum wells, was introduced by Nobel Laureate L. Esaki in the 1970s. Since then, this material system has drawn a lot of attention especially for infrared detection. In recent years, T2SL material system has experienced incredible improvements in material quality, device structure designs and device fabrication process which elevated the performances of T2SL-based photo-detectors to a comparable level to the state-of-the-art material systems for infrared detection such as Mercury Cadmium Telluride (MCT). In this paper, we will present the current status of T2SL-based photo-detectors and focal plane arrays for imaging in different infrared regions, from SWIR to VLWIR, and the future outlook of this material system. [reprint (PDF)]
19.	Shortwave quantum cascade laser frequency comb for multi-heterodyne spectroscopy Q. Y. Lu, S. Manna, D. H. Wu, S. Slivken, and M. Razeghi Applied Physics Letters 112, 141104-- April 3, 2018 ...[Visit Journal] Quantum cascade lasers (QCLs) are versatile light sources with tailorable emitting wavelengths covering the mid-infrared and terahertz spectral ranges. When the dispersion is minimized, frequency combs can be directly emitted from quantum cascade lasers via four-wave mixing. To date, most of the mid-infrared quantum cascade laser combs are operational in a narrow wavelength range wherein the QCL dispersion is minimal. In this work, we address the issue of very high dispersion for shortwave QCLs and demonstrate 1-W dispersion compensated shortwave QCL frequency combs at λ~5.0 μm, spanning a spectral range of 100 cm⁻¹. The multi-heterodyne spectrum exhibits 95 equally spaced frequency comb lines, indicating that the shortwave QCL combs are ideal candidates for high-speed high-resolution spectroscopy [reprint (PDF)]
19.	High performance LWIR Type-II InAs/GaSb superlattice photodetectors and infrared focal plane array Y. Wei, A. Hood, A. Gin, V. Yazdanpanah, M. Razeghi and M. Tidrow SPIE Conference, Jose, CA, Vol. 5732, pp. 309-- January 22, 2005 ...[Visit Journal] We report on the demonstration of a focal plane array based on Type-II InAs-GaSb superlattices grown on n-type GaSb substrate with a 50% cutoff wavelength at 10 μm. The surface leakage occurring after flip-chip bonding and underfill in the Type-II devices was suppressed using a double heterostructure design. The R₀A of diodes passivated with SiO₂ was 23 Ω·cm² after underfill. A focal plane array hybridized to an Indigo readout integrated circuit demonstrated a noise equivalent temperature difference of 33 mK at 81 K, with an integration time of 0.23 ms. [reprint (PDF)]
19.	MOCVD challenge for III-V semiconductor materials for photonic and electronic devices on alternative substrates M. Razeghi, M. Defour , F. Omnes, P. Maurel , E. Bigan , O. Acher, J. Nagle, F. Brillouet , J.C. Portal M. Razeghi, M. Defour, F. Omnes, P. Maurel, E. Bigan, O. Acher, J. Nagle, F. Brillouet, J.C. Portal, MOCVD challenge for III-V semiconductor materials for photonic and electronic devices on alternative substrates, Journal of Crystal Growth, Volume 93, Issues 1–4, 1988, Pages 776-781,-- January 1, 1988 ...[Visit Journal] High quality II[-V semiconductor heterojunctions, quantum wells and superlauices have been grown on lattice matched and alternative substrates such as silicon for photonic and electronic devices, using low pressure metalorganic chemical vapor deposition growth technique. [reprint (PDF)]
19.	Very High Average Power Quantum Cascade Lasers by GasMBE S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, Vol. 4999, pp. 59-- January 27, 2003 ...[Visit Journal] Very high average power QCLs are demonstrated within the 5.8 - 9 µm wavelength range. At longer wavelengths, scaling of the power is demonstrated by increasing the number of emitting regions in the waveguide core. At λ = 9 µm, over 3.5 W of peak power per facet has been demonstrated at room temperature for a single 25 µm by 3 mm diode, with an average power of 150 mW at 6% duty cycle. At shorter wavelengths, highly strain-balanced heterostructures are used to create a high coduction band offset and minimize leakage current. At λ = 6 µm, utilizing a high reflective coating and epilayer-down mounting of the laser, we demonstrate 225 mW of average power from a single facet at room temperature. Increasing the conduction band offset further and optimizing the doping in the injector region has led to demonstration of > 250 mW average power (λ = 5.8 µm) at > 50% duty cycle for a 20 µm by 2 mm HR coated diode bonded epilayer-down to a copper heatsink. Also at room temperature, use of Au electroplating and wider ridges has allowed us to further demonstrate without epilayer-down bonding, 0.67 W average power at 17% duty cycle from a single 40 µm by 2 mm HR coated laser. [reprint (PDF)]
19.	High-speed short wavelength infrared heterojunction phototransistors based on type II superlattices Jiakai Li; Arash Dehzangi; Donghai Wu; Manijeh Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128813-- January 31, 2020 ...[Visit Journal] A two terminal short wavelength infrared heterojunction phototransistors based on type-II InAs/AlSb/GaSb on GaSb substrate are designed fabricated and presented. With the base thickness of 40 nm, the device exhibited 100% cut-off wavelengths of ~2.3 μm at 300K. The saturated peak responsivity value is of 325.5 A/W at 300K, under front-side illumination without any anti-reflection coating. A saturated optical gain at 300K was 215 a saturated dark current shot noise limited specific detectivity of 4.9×10¹¹ cm·Hz^½/W at 300 K was measured. Similar heterojunction phototransistor structure was grown and fabricated with different method of processing for high speed testing. For 80 μm diameter circular diode size under 20 V applied reverse bias, a −3 dB cut-off frequency of 1.0 GHz was achieved, which showed the potential of type-II superlattice based heterojunction phototransistors to be used for high speed detection. [reprint (PDF)]
19.	Exciton localization in group-III nitride quantum wells V.I. Litvinov and M. Razeghi Physical Review B 59 (15)-- May 15, 1999 ...[Visit Journal] Exciton density of states broadened by compositional disorder in the group-III nitride quantum well is calculated. The excitonic photoluminescence linewidth is estimated and related to the material parameters of the alloy for two limiting cases of two-dimensional (2D) and three-dimensional excitons in the quantum well. It is shown that the effect of the compositional fluctuations depends on dimensionality of the exciton: the 2D excitons are more sensitive to the inhomogeneities than 3D ones. The broad near-band-gap energy states distribution for quasi-two-dimensional excitons is consistent with the experimental evidence of the spontaneous and stimulated emissions from excitonic states localized on compositional fluctuations. [reprint (PDF)]
19.	Schottky MSM Photodetectors on GaN Films Grown on Sapphire by Lateral Epitaxial Overgrowth P. Kung, D. Walker, P. Sandvik, M. Hamilton, J. Diaz, I.H. Lee and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] We report the growth and characterization of Schottky based metal-semiconductor-metal ultraviolet photodetectors fabricated on lateral epitaxially overgrown GaN films. The lateral epitaxial overgrowth of GaN was carried out on basal plane sapphire substrates by low pressure metalorganic chemical vapor deposition and exhibited lateral growth rates more than 5 times as high as vertical growth rates. The spectral responsivity, the dependence on bias voltage, on incident optical power, and the time response of these photodetectors have been characterized. Two detector orientations were investigated: one with the interdigitated finger pattern parallel and the other perpendicular to the underlying SiO_x mask stripes. [reprint (PDF)]
19.	320x256 Solar-Blind Focal Plane Arrays based on Al_xGa_1-xN R. McClintock, K. Mayes, A. Yasan, D. Shiell, P. Kung, and M. Razeghi Applied Physics Letters, 86 (1)-- January 3, 2005 ...[Visit Journal] We report AlGaN-based back-illuminated solar-blind ultraviolet focal plane arrays operating at a wavelength of 280 nm. The electrical characteristics of the individual pixels are discussed, and the uniformity of the array is presented. The p–i–n photodiode array was hybridized to a 320×256 read-out integrated circuit entirely within our university research lab, and a working 320×256 camera was demonstrated. Several example solar-blind images from the camera are also provided. [reprint (PDF)]
19.	Suppressing Spectral Crosstalk in Dual-Band LongWavelength Infrared Photodetectors With Monolithically Integrated Air-Gapped Distributed Bragg Reﬂectors Yiyun Zhang, Abbas Haddadi, Arash Dehzangi , Romain Chevallier, Manijeh Razeghi IEEE Journal of Quantum Electronics Volume: 55, Issue:1-- November 22, 2018 ...[Visit Journal] Antimonide-based type-II superlattices (T2SLs) have made possible the development of high-performance infrared cameras for use in a wide variety of thermal imaging applications, many of which could beneﬁt from dual-band imaging. The performance of this material system has not reached its limits. One of the key issues in dual-band infrared photodetection is spectral crosstalk. In this paper, air-gapped distributed Bragg reﬂectors (DBRs) have been monolithically integrated between the two channels in long-/very long-wavelength dualband InAs/InAs_1−xSb_x/AlAs_1−xSb_x-based T2SLs photodetectors to suppress the spectral crosstalk. This air-gapped DBR has achieved a signiﬁcant spectral suppression in the 4.5–7.5-µm photonic stopband while transmitting the optical wavelengths beyond 7.5 µm, which is conﬁrmed by theoretical calculations, numerical simulation, and experimental results. [reprint (PDF)]

Page 3 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)