Center for Quantum Devices - Most Downloaded Journal Articles

Page 29 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

10.	Transport properties in n-type InSb films grown by metalorganic chemical vapor deposition S.N. Song, J.B. Ketterson, Y.H. Choi, R. Sudharsanan, and M. Razeghi Applied Physics Letters 63 (7)-- August 16, 1993 ...[Visit Journal] We have measured the temperature and magnetic field dependence of the Hall mobility and transverse magnetoresistance in n-type InSb films epitaxially grown on GaAs substrates by metalorganic chemical vapor deposition. The films show a giant magnetoresistance: e.g., at 240 K the resistivity increases over 20 times at a magnetic field of 5 T; the low field coefficient of resistivity at 77 K is as high as 47.5 μ·Ω· cm/G. The Hall mobility decreases with magnetic field and saturates at higher fields. By taking the interface carrier transport into account, the observed field dependence of the Hall mobility and magnetoresistance may be understood based on a two-layer model. [reprint (PDF)]
10.	EPR Investigations of a Structural Phase Change in Lead Phosphate M. RAZEGHI M. RAZEGHI: EPR Investigations of a Structural Phase Change phys. stat. sol. (b) 108, 175 (1981)-- November 1, 1981 ...[Visit Journal] The temperature dependence of the EPR line width of the Mn2+ and Gd3+ in Pb3(PO4)2 is investigated from -270 to 500 °C. At the first-order ferroelastic transition point (180 °C), an abrupt change in the fine-structure splitting as well as in the resonance line width is observed. Various contributions to fine structure D and E parameters of Mn2+ and Gd3+ are computed, using a point-multipole model. For temperatures near to Tc the correlation time of the fluctuations is estimated to be greater than 10−9. [reprint (PDF)]
10.	Recent Advances in LWIR Type-II InAs/GaSb Superlattice Photodetectors and Focal Plane Arrays at the Center for Quantum Devices M. Razeghi, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E.K. Huang, M.Z. Tidrow, and V. Nathan IEEE Proceedings, Vol. 97, No. 6, p. 1056-1066-- June 1, 2009 ...[Visit Journal] In recent years, Type-II InAs/GaSb superlattice photo-detectors have experienced significant improvements in material quality, structural designs, and imaging applications. They now appear to be a possible alternative to the state-of-the-art HgCdTe (MCT) technology in the long and very long wavelength infrared regimes. At the Center for Quantum Devices, we have successfully realized very high quantum efficiency, very high dynamic differential resistance R₀A - product LWIR Type – II InAs/GaSb superlattice photodiodes with efficient surface passivation techniques. The demonstration of high quality LWIR Focal Plane Arrays that were 100 % fabricated in - house reaffirms the pioneer position of this university-based laboratory. [reprint (PDF)]
10.	Background limited performance of long wavelength infrared focal plane arrays fabricated from type-II InAs/GaSb M-structure superlattice P.Y. Delaunay, B.M. Nguyen and M. Razeghi SPIE Porceedings, Vol. 7298, Orlando, FL 2009, p. 72981Q-- April 13, 2009 ...[Visit Journal] Recent advances in growth techniques, structure design and processing have lifted the performance of Type-II InAs/GaSb superlattice photodetectors. The introduction of a M-structure design improved both the dark current and R0A of Type-II photodiodes. This new structure combined with a thick absorbing region demonstrated background limited performance at 77K for a 300K background and a 2-π field of view. A focal plane array with a 9.6 μm 50% cutoff wavelength was fabricated with this design and characterized at 80K. The dark current of individual pixels was measured around 1.3 nA, 7 times lower than previous superlattice FPAs. This led to a higher dynamic range and longer integration times. The quantum efficiency of detectors without anti-reflective coating was 72%. The noise equivalent temperature difference reached 23 mK. The deposition of an anti-reflective coating improved the NEDT to 20 mK and the quantum efficiency to 89%. [reprint (PDF)]
10.	Pulsed metal-organic chemical vapor deposition of high quality AlN/GaN superlattices for near-infrared intersubband transitions C. Bayram, N. Pere-Laperne, R. McClintock, B. Fain and M. Razeghi Applied Physics Letters, Vol. 94, No. 12, p. 121902-1-- March 23, 2009 ...[Visit Journal] A pulsed metal-organic chemical vapor deposition technique is developed for the growth of high-quality AlN/GaN superlattices (SLs) with intersubband (ISB) transitions at optical communications wavelengths. Tunability of the AlN and GaN layers is demonstrated. Indium is shown to improve SL surface and structural quality. Capping thickness is shown to be crucial for ISB transition characteristics. Effects of barrier- and well-doping on the ISB absorption are reported. [reprint (PDF)]
10.	High Power Quantum Cascade Lasers Operating at Room Temperature M. Razeghi and S. Slivken Journal of the Korean Physical Society, Vol. 42, pp. S637-S641-- February 1, 2003 ...[Visit Journal] In this paper, some key design and technology issues for development of high power quantum cascade lasers are discussed. The scaling of power output with the number of emitting stages is shown. As part of this work, high power, 75-stage, λ = 9 μm lasers have been demonstrated with a peak power of 7 W at room temperature. This power is a direct result of high quality material growth and a low loss waveguide design. Similar results are demonstrated at a shorter wavelength (λ = 6.1 μm) utilizing a strain-balanced active region/injector design. For a 30-stage structure, 2 W peak power and 250 mW average power have been demonstrated at room temperature. Lastly, a timeline comparison of QCL laser performance is presented in terms of room temperature threshold current density and peak output power for various groups. [reprint (PDF)]
10.	Intermixing of GaInP/GaAs Multiple Quantum Wells C. Francis, M.A. Bradley, P. Boucaud, F.H. Julien and M. Razeghi Applied Physics Letters 62 (2)-- January 11, 1993 ...[Visit Journal] The intermixing of GaInP‐GaAs superlattices induced by a heat treatment is investigated as a function of the annealing temperature and duration. Photoluminescence experiments reveal a large red shift of the effective band gap of the annealed quantum wells thus indicating a dominant self‐diffusion of the group III atoms which is confirmed by secondary ion mass spectroscopic measurements. For long enough annealing durations, the red shift saturates and even decreases due to the competing slower self‐diffusion of the group V atoms. Experiments are well understood based on a simple diffusion model. [reprint (PDF)]
10.	Characteristics of Self-Assembled InGaAs/InGaP Quantum Dot Mid-Infrared Photoconductive Detectors Grown by Low Pressure MOCVD S. Kim, M. Erdtmann, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] We report the first self-assembled InGaAs/InGaP quantum dot intersubband infrared photoconductive detectors (QDIPs) grown on semi-insulating GaAs substrate by low pressure metal organic chemical vapor deposition (MOCVD). The InGaAs quantum dots were constructed on an InGaP matrix as self assembling in Stranski-Krastanow growth mode in optimum growth conditions. The detector structure was prepared for single layer and multi-stacked quantum dots for active region. Normal incident photoconductive response was observed at a peak wavelength of 5.5 μm with a high responsivity of 130 mA/W, and a detectivity of 4.74 X 10⁷ cm·Hz^½/W at 77 K for multi-stack QDIP. Low temperature photoresponse of the single quantum dot photodetector was characterized. Peak response was obtained between 16 K and 60 K. The detailed dark current noise measurements were carried on single and multistack quantum dot infrared detectors. High photoconductive gain as 7.6 x 10³ biased at 0.5 V results in increasing the intersubband carrier relaxation time as two order of magnitude compared quantum well infrared photodetectors. [reprint (PDF)]
10.	Comparison of chemical and laser lift-off for the transfer of InGaN-based p-i-n junctions from sapphire to glass substrates D. J. Rogers ; P. Bove ; F. Hosseini Teherani ; K. Pantzas ; T. Moudakir ; G. Orsal ; G. Patriarche ; S. Gautier ; A. Ougazzaden ; V. E. Sandana ; R. McClintock ; M. Razeghi Proc. SPIE 8626, Oxide-based Materials and Devices IV, 862611 (March 18, 2013)-- March 18, 2013 ...[Visit Journal] InGaN-based p-i-n structures were transferred from sapphire to soda-lime glass substrates using two approaches: (1) laser-lift-off (LLO) and thermo-metallic bonding and (2) chemical lift-off (LLO) by means sacrificial ZnO templates and direct wafer bonding. Both processes were found to function at RT and allow reclaim of the expensive single crystal substrate. Both approaches have also already been demonstrated to work for the wafer-scale transfer of III/V semiconductors. Compared with the industry-standard LLO, the CLO offers the added advantages of a lattice match to InGaN with higher indium contents, no need for an interfacial adhesive layer (which facilitates electrical, optical and thermal coupling), no damaged/contaminated GaN surface layer, simplified sapphire reclaim (GaN residue after LLO may complicate reclaim) and cost savings linked to elimination of the expensive LLO process. [reprint (PDF)]
10.	Thin-Film Antimonide-Based Photodetectors Integrated on Si Yiyun Zhang , Member, IEEE, Abbas Haddadi, Member, IEEE, Romain Chevallier, Arash Dehzangi, Member, IEEE, and Manijeh Razeghi , Life Fellow, IEEE IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 54, NO. 2-- April 1, 2018 ...[Visit Journal] Monolithic integration of antimonide (Sb)-based compound semiconductors on Si is in high demand to enrich silicon photonics by extending the detection range to longer infrared wavelengths. In this paper, we have demonstrated the damage-free transfer of large-area (1×1 cm² ) narrow-bandgap Sb-based type-II superlattice (T2SL)-based thin-film materials onto a Si substrate using a combination of wafer-bonding and chemical epilayer release techniques. An array of Sb-based T2SL-based long-wavelength infrared (LWIR) photodetectors with diameters from 100 to 400 μm has been successfully fabricated using standard "top–down" processing technique. The transferred LWIR photodetectors exhibit a cut-off wavelength of λ 8.6 μm at 77 K. The dark current density of the transferred photodetectors under 200 mV applied bias at 77 K is as low as 5.7×10⁻⁴ A/cm² and the R×A reaches 66.3 Ω·cm², exhibiting no electrical degradation compared with reference samples on GaSb native substrate. The quantum efficiency and peak responsivity at 6.75 μm (@77 K, 200 mV) are 46.2% and 2.44 A/W, respectively. The specific detectivity (D^*) at 6.75 μm reaches as high as 1.6×10¹¹ cm·Hz^1/2/W under 200 mV bias at 77 K. Our method opens a reliable pathway to realize high performance and practical Sb-based optoelectronic devices on a Si platform. [reprint (PDF)]
10.	Sampled grating, distributed feedback quantum cascade lasers with broad tunability and continuous operation at room temperature S. Slivken, N. Bandyopadhyay, S. Tsao, S. Nida, Y. Bai, Q.Y. Lu and M. Razeghi Applied Physics Letters, Vol. 100, No. 26, p. 261112-1-- June 25, 2012 ...[Visit Journal] A dual-section, single-mode quantum cascade laser is demonstrated in continuous wave at room temperature with up to 114 nm (50 cm⁻¹) of tuning near a wavelength of 4.8 μm. Power above 100 mW is demonstrated, with a mean side mode suppression ratio of 24 dB. By changing the grating period, 270 nm (120 cm⁻¹) of gap-free electrical tuning for a single gain medium has been realized. [reprint (PDF)]
10.	Deep Fe and intrinsic defect levels in Ga0.47In0.53As/InP K.‐H. Goetz; D. Bimberg; K.‐A. Brauchle; H. Jürgensen; J. Selders; M. Razeghi; E. Kuphal K.‐H. Goetz, D. Bimberg, K.‐A. Brauchle, H. Jürgensen, J. Selders, M. Razeghi, E. Kuphal; Deep Fe and intrinsic defect levels in Ga0.47In0.53As/InP. Appl. Phys. Lett. 1 February 1985; 46-- February 1, 1985 ...[Visit Journal] Two deep traps in Ga0.47In0.53As/InP:Fe at a depth of 110 meV and 150 meV, respectively, are observed for the first time using low‐temperature photoluminescence and deep level transient spectroscopy. The dependence of luminescence intensity on the growth process itself (liquid phase epitaxy, vapor phase epitaxy, and metalorganic chemical vapor deposition) and its parameters (growth temperature, layer thickness) and the substrate doping is reported and leads to the unambigous identification of the 150‐meV acceptorlike trap as being caused by Fe impurities. Fe diffuses from the substrate to the epitaxial layer during the growth process. This outdiffusion is less pronounced for layers grown at lower temperature. The level at 110 meV which is also observed in layers grown on InP:S substrate is tentatively assigned to an intrinsic defect of Ga0.47In0.53As. [reprint (PDF)]
10.	8.5 μm Room Temperature Quantum Cascade Lasers Grown by Gas-Source Molecular Beam Epitaxy S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, -- January 28, 1998 ...[Visit Journal] We report room-temperature pulsed-mode operation of 8.5 μm quantum cascade lasers grown by gas-source molecular beam epitaxy. The theory necessary to understand the operation of the laser is presented and current problems are analyzed. Very good agreement is shown to exist between theoretical and experimental emission wavelengths. The high- temperature operation is achieved with 1 μs pulses at a repetition rate of 200 Hz. Peak output power in these conditions is in excess of 700 mW per 2 facets at 79 K and 25 mW at 300 K. Threshold current as a function of temperature shows an exponential dependence with T₀ equals 188 K for a 1.5 mm cavity. [reprint (PDF)]
10.	Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface R.J Nicholas a, M.A Brummell a , J.C Portal b, M Razeghi c, M.A Poisson R.J Nicholas, M.A Brummell, J.C Portal, M Razeghi, M.A Poisson, Quantum oscillations at a Ga0.47In0.53AsInP heterojunction interface, Solid State Communications, Volume 43, Issue 11, 1982, Pages 825-828,-- September 1, 1982 ...[Visit Journal] We report the observation of a two dimensional gas of high mobility electrons at the interface of a Ga0.47In0.53AsInP heterojunction grown by MOCVD. The two dimensional electron concentrations and effective mass are determined by Shubnikov-de Haas studies, and compared with theoretical predictions. Evidence of an enhancement of the g-factor is observed. We also report observations of very pronounced quantum Hall steps as seen in GaAs-GaAlAs heterojunctions. [reprint (PDF)]
10.	Electrical Transport Properties of Highly Doped N-type GaN Epilayers H.J. Lee, M.G. Cheong, E.K. Suh, and M. Razeghi SPIE Conference, San Jose, CA, -- January 28, 1998 ...[Visit Journal] Temperature-dependent Hall-effects in MOCVD-grown Si-doped GaN epilayers were measured as a function of temperature in the range 10-800 K. The results were satisfactorily analyzed in terms of a two-band model including the (Gamma) and impurity bands at lower temperatures than room. The (Gamma) band electrons are dominant only high temperatures. The ionized impurity scattering is the most important in the (Gamma) band except at very high temperatures. [reprint (PDF)]
10.	High Frequency Extended Short-Wavelength Infrared Heterojunction Photodetectors Based on InAs/GaSb/AlSb Type-II Superlattices Romain Chevallier, Abbas Haddadi, Ryan McClintock, Arash Dehzangi , Victor Lopez-Dominguez, Pedram Khalili Amiri, Manijeh Razeghi IEEE JOURNAL OF QUANTUM ELECTRONICS, VOL. 54, NO. 6-- December 1, 2018 ...[Visit Journal] InAs/GaSb/AlSb type-II superlattice-based photodetectors, with 50% cut-off wavelength of 2.1 µm and a −3 dB cut-off frequency of 4.8 GHz, are demonstrated, for 10 µm diameter circular mesas under 15 V applied reverse bias. A study of the cut-off frequency with applied bias and mesa size was performed to evaluate some of the limiting factors of photodetectors high frequency performance. [reprint (PDF)]
10.	Broadband monolithically-tunable quantum cascade lasers Wenjia Zhou, Ryan McClintock, Donghai Wu, Steven Slivken, Manijeh Razeghi Proc. SPIE 10540, Quantum Sensing and Nano Electronics and Photonics XV, 105400A-- January 26, 2018 ...[Visit Journal] Mid-infrared lasers, emitting in the spectral region of 3-12 μm that contain strong characteristic vibrational transitions of many important molecules, are highly desirable for spectroscopy sensing applications. High efficiency quantum cascade lasers have been demonstrated with up to watt-level output power in the mid-infrared region. However, the wide wavelength tuning, which is critical for spectroscopy applications, is still largely relying on incorporating external gratings, which have stability issues. Here, we demonstrate the development a monolithic, widely tunable quantum cascade laser source emitting between 6.1 and 9.2 μm through an on-chip integration of a sampled grating distributed feedback tunable laser array with a beam combiner. A compact tunable laser system was built to drive the individual lasers within the array and coordinate the driving of the laser array to produce desired wavelength. A broadband spectral measurement (520cm^-1) of methane shows excellent agreement with Fourier transform infrared spectrometer measurement. Further optimizations have led to high performance monolithic tunable QCLs with up to 65 mW output while delivering fundamental mode outputs. [reprint (PDF)]
10.	Investigation of the Heteroepitaxial Interfaces in the GaInP/GaAs Superlattices by High Resolution X-Ray Diffraction and Dynamical Solutions Xiaoguang He and Manijeh Razeghi Journal of Applied Physics 73 (7)-- April 1, 1993 ...[Visit Journal] Two GaAs/GaInP superlattices grown on GaAs substrates by low‐pressure metalorganic chemical vapor deposition have been studied using high resolution x‐ray diffraction measurements and simulations by solving Tagaki–Taupin equations. The strained layers at both interfaces of the GaAs well are identified from the simulations of the measured diffraction patterns. The purging of indium at the interface of GaInP/GaAs accounts for the strained layer at the GaInP/GaAs interface while the pressure difference in the gas lines, which results in the different traveling time to the sample surface, is attributed to the indium‐poor strained layer at the GaAs/GaInP interface. It is shown that high‐resolution x‐ray diffraction measurements combined with a dynamical simulation, are sensitive tools to study the heteroepitaxial interfaces on an atomic layer scale. In addition, the influence of a miscut of the substrate on the measurement is discussed in the article. It is shown that even though the miscut is small, the diffraction geometry is already an asymmetric one. More than 10% error in the superlattice period for a 2° miscut substrate can result when the miscut substrate is considered a symmetric geometry. [reprint (PDF)]
10.	Gas sensing spectroscopy system utilizing a sample grating distributed feedback quantum cascade laser array and type II superlattice detector Nathaniel R. Coirier; Andrea I. Gomez-Patron; Manijeh Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128815-- January 31, 2020 ...[Visit Journal] Gas spectroscopy is a tool that can be used in a variety of applications. One example is in the medical field, where it can diagnose patients by detecting biomarkers in breath, and another is in the security field, where it can safely alert personnel about ambient concentrations of dangerous gas. In this paper, we document the design and construction of a system compact enough to be easily deployable in defense, healthcare, and chemical safety environments. Current gas sensing systems use basic quantum cascade lasers (QCLs) or distributed feedback quantum cascade lasers (DFB QCLs) with large benchtop signal recovery systems to determine gas concentrations. There are significant issues with these setups, namely the lack of laser tunability and the lack of practicality outside of a very clean lab setting. QCLs are advantageous for gas sensing purposes because they are the most efficient lasers at the mid infrared region (MIR). This is necessary since gases tend to have stronger absorption lines in the MIR range than in the near-infrared (NIR) region. To incorporate the efficiency of a QCL with wide tuning capabilities in the MIR region, sampled grating distributed feedback (SGDFB) QCLs are the answer as they have produced systems that are widely tunable, which is advantageous for scanning a robust and complete absorption spectrum. The system employs a SGDFB QCL array emitter, a Type II InAsSb Superlattice detector receiver, a gas cell, and a cooling system. [reprint (PDF)]
10.	Midinfrared Semiconductor Photonics – A Roadmap:Quantum Cascade Lasers MANIJEH RAZEGHI arXiv:2511.03868 [physics.optics] ...[Visit Journal] Mid-wave infrared (IR) quantum cascade lasers (QCLs) offer high output power, excellent efficiency, broad wavelength tunability, and elevated operating temperatures, especially when operating in the 3–12 μm wavelength range. These characteristics make them highly promising for a wide range of applications, including high-resolution molecular spectroscopy, ultra-low-loss optical fiber communications using fluoride-based glasses (with attenuation below 2.5×10⁻⁴ dB/km), trace gas detection, air pollution monitoring (as many molecules, particularly hydrocarbons, exhibiting strong absorption lines in this spectral region), and medical diagnostics. This article presents a comprehensive overview of the development of QCLs, highlighting key milestones, the current state of the technology, and future directions, framed within the broader context of the Semiconductor Mid-Infrared Photonics Roadmap.
10.	High quantum efficiency two color type-II InAs/GaSb n-i-p-p-i-n photodiodes P.Y. Delaunay, B.M. Nguyen, D. Hoffman, A. Hood, E.K. Huang, M. Razeghi, and M.Z. Tidrow Applied Physics Letters, Vol. 92, No. 11, p. 111112-1-- March 17, 2008 ...[Visit Journal] A n-i-p-p-i-n photodiode based on type-II InAs/GaSb superlattice was grown on a GaSb substrate. The two channels, with respective 50% of responsivity cutoff wavelengths at 7.7 and 10 µm, presented quantum efficiencies (QEs) of 47% and 39% at 77 K. The devices can be operated as two diodes for simultaneous detection or as a single n-i-p-p-i-n detector for sequential detection. In the latter configuration, the QEs at 5.3 and 8.5 µm were measured as high as 40% and 39% at 77 K. The optical cross-talk between the two channels could be reduced from 0.36 to 0.08 by applying a 50 mV bias. [reprint (PDF)]
10.	An accurate method to check chemical interfaces of epitaxial III‐V compounds R. Bisaro; G. Laurencin; A. Friederich; M. Razeghi Appl. Phys. Lett. 40 (11): 978–980 (1982)-- June 1, 1982 ...[Visit Journal] We have developed a method of chemical beveling coupled with line scan Auger measurements to check abrupt interfaces of epitaxial III‐V compounds. Interface widths between 53 and 89 Å have been measured by this method for an InP/Ga0.47In0.53As/InP double heterostructure grown by low pressure metalorganic chemical vapor deposition. The ultimate width checkable by this method lies between 10 and 15 Å and is of the order of magnitude of the escape depth of the Auger electrons selected. [reprint (PDF)]
10.	High performance mid-wavelength quantum dot infrared photodetectors for focal plane arrays M. Razeghi, H. Lim, S. Tsao, M. Taguchi, W. Zhang and A.A. Quivy SPIE Conference, San Diego, CA, Vol. 6297, pp. 62970C-- August 13, 2006 ...[Visit Journal] Quantum dot infrared photodetectors (QDIPs) have recently emerged as promising candidates for detection in the middle wavelength infrared (MWIR) and long wavelength infrared (LWIR) ranges. Here, we report our recent results for mid-wavelength QDIPs grown by low-pressure metalorganic chemical vapor deposition. Three monolayer of In_0.68Ga_0.32As self-assembled via the Stranski-Krastanov growth mode and formed lens-shaped InGaAs quantum dots with a density around 3×10₁₀ cm^-2. The peak responsivity at 77 K was measured to be 3.4 A/W at a bias of -1.9 V with 4.7 µm peak detection wavelength. Focal plane arrays (FPAs) based on these devices have been developed. The preliminary result of FPA imaging is presented. [reprint (PDF)]
10.	Characterization of ZnO thin films grown on c-sapphire by pulsed laser deposition as templates for regrowth of zno by metal organic chemical vapor deposition D. J. Rogers ; F. Hosseini Teherani ; C. Sartel ; V. Sallet ; F. Jomard ; P. Galtier ; M. Razeghi Proc. SPIE 7217, Zinc Oxide Materials and Devices IV, 72170F (February 17, 2009)-- February 17, 2009 ...[Visit Journal] The use of ZnO template layers grown Pulsed Laser Deposition (PLD) has been seen to produce dramatic improvements in the surface morphology, crystallographic quality and optical properties of ZnO layers grown on c-sapphire substrates by Metal Organic Chemical Vapor Deposition. This paper provides complementary details on the PLD-grown ZnO template properties. [reprint (PDF)]
10.	Gain-length scaling in quantum dot/quantum well infrared photodetectors T. Yamanaka, B. Movaghar, S. Tsao, S. Kuboya, A. Myzaferi and M. Razeghi Virtual Journal of Nanoscale Science & Technology-- September 14, 2009 ...[Visit Journal][reprint (PDF)]

Page 29 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)