Center for Quantum Devices - Most Downloaded Journal Articles

Page 28 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

11.	High-Performance InP-Based Mid-IR Quantum Cascade Lasers M. Razeghi IEEE Journal of Selected Topics in Quantum Electronics, Vol. 15, No. 3, May-June 2009, p. 941-951.-- June 5, 2009 ...[Visit Journal] Quantum cascade lasers (QCLs) were once considered as inefficient devices, as the wall-plug efficiency (WPE) was merely a few percent at room temperature. But this situation has changed in the past few years, as dramatic enhancements to the output power andWPE have been made for InP-based mid-IR QCLs. Room temperature continuous-wave (CW) output power as high as 2.8 W and WPE as high as 15% have now been demonstrated for individual devices. Along with the fundamental exploration of refining the design and improving the material quality, a consistent determination of important device performance parameters allows for strategically addressing each component that can be improved potentially. In this paper, we present quantitative experimental evidence backing up the strategies we have adopted to improve the WPE for QCLs with room temperature CW operation. [reprint (PDF)]
11.	Generalized k·p perturbation theory for atomic-scale superlattices H. Yi and M. Razeghi Physical Review B 56 (7)-- August 15, 1997 ...[Visit Journal] We present a generalized k⋅p perturbation method that is applicable for atomic-scale superlattices. The present model is in good quantitative agreement with full band theories with local-density approximation, and approaches results of the conventional k⋅p perturbation method (i.e., Kane’s Hamiltonian) with the envelope function approximation for superlattices with large periods. The indirect band gap of AlAs/GaAs superlattices with short periods observed in experiments is explained using this method. [reprint (PDF)]
11.	High-temperature high-power continuous-wave operation of buried heterostructure quantum-cascade lasers A. Evans, J.S. Yu, J. David, L. Doris, K. Mi, S. Slivken, and M. Razeghi Applied Physics Letters, 84 (3)-- January 19, 2004 ...[Visit Journal] We report cw operation of buried heterostructure quantum-cascade lasers (λ=6 µm) using a thick electroplated Au top contact layer and epilayer-up bonding on a copper heat sink up to a temperature of 333 K (60 °C). The high cw optical output powers of 446 mW at 293 K, 372 mW at 298 K, and 30 mW at 333 K are achieved with threshold current densities of 2.19, 2.35, and 4.29 kA/cm² respectively, for a high-reflectivity-coated, 9-µm-wide and 3-mm-long laser [reprint (PDF)]
11.	High Detectivity InAs Quantum-Dot Infrared Photodetectors Grown on InP by Metalorganic Chemical Vapor Deposition W. Zhang, H. Lim, M. Taguchi, S. Tsao, B. Movaghar, and M. Razeghi Applied Physics Letters, 86 (19)-- May 9, 2005 ...[Visit Journal] We report a high-detectivity InAs quantum-dot infrared photodetector. The InAs quantum dots were grown by self-assembly on InP substrates via low-pressure metal–organic chemical–vapor deposition. Highly uniform quantum dots with a density of 4×10¹⁰ cm² were grown on a GaAs/InP matrix. Photoresponse was observed at temperatures up to 160 K with a peak of 6.4 µm and cutoff of 6.6 µm. Very low dark currents and noise currents were obtained by inserting Al_0.48In_0.52As current blocking layers. The background-limited performance temperature was 100 K. A detectivity of 1.0×10¹⁰ cm·Hz^½/W was obtained at 77 K with a bias of –1.1 V. [reprint (PDF)]
11.	Microstructural compositional, and optical characterization of GaN grown by metal organic vapor phase epitaxy on ZnO epilayers D.J. Rogers, F. Hosseini Teherani, T. Moudakir, S. Gautier, F. Jomard, M. Molinari, M. Troyon, D. McGrouther, J.N. Chapman, M. Razeghi and A. Ougazzaden Journal of Vacuum Science and Technology B, Vol. 27, No. 3, May/June, p. 1655-1657-- May 29, 2009 ...[Visit Journal] This article presents the results of microstructural, compositional, and optical characterization of GaN films grown on ZnO buffered c-sapphire substrates. Transmission electron microscopy showed epitaxy between the GaN and the ZnO, no degradation of the ZnO buffer layer, and no evidence of any interfacial compounds. Secondary ion mass spectroscopy revealed negligible Zn signal in the GaN layer away from the GaN/ZnO interface. After chemical removal of the ZnO, room temperature (RT) cathodoluminescence spectra had a single main peak centered at ~ 368 nm (~3.37 eV), which was indexed as near-band-edge (NBE) emission from the GaN layer. There was no evidence of the ZnO NBE peak, centered at ~379 nm (~3.28 eV), which had been observed in RT photoluminescence spectra prior to removal of the ZnO. [reprint (PDF)]
11.	Radiometric characterization of long-wavelength infrared type II strained layer superlattice focal plane array under low-photon irradiance conditions J. Hubbs, V. Nathan, M. Tidrow, and M. Razeghi Optical Engineering, Vol. 51, No. 6, p. 064002-1-- June 15, 2012 ...[Visit Journal] We present the results of the radiometric characterization of an “M” structure long wavelength infrared Type-II strained layer superlattice(SLS) infrared focal plane array (IRFPA) developed by Northwestern University (NWU). The performance of the M-structure SLS IRFPA was radiometrically characterized as a function of photon irradiance, integration time, operating temperature, and detector bias. Its performance is described using standard figures of merit: responsivity, noise, and noise equivalent irradiance. Assuming background limited performance operation at higher irradiances, the detector quantum efficiency for the SLS detector array is approximately 57%. The detector dark density at 80 K is 142 μA∕cm², which represents a factor of seven reduction from previously measured devices. [reprint (PDF)]
11.	Room temperature continuous wave THz frequency comb based on quantum cascade lasers M. Razeghi; Q. Y. Lu; F. H. Wang; D. H. Wu; S. Slivken Proc. SPIE 11124, Terahertz Emitters, Receivers, and Applications X, 1112407-- September 6, 2019 ...[Visit Journal] Frequency combs, spectra of phase-coherent equidistant lines, have revolutionized time and frequency metrology. The recently developed quantum cascade laser (QCL) comb has exhibits great potential with high power and broadband spectrum. However, in the terahertz (THz) range, cryogenic cooling has to be applied for THz QCL combs. We report a room temperature THz frequency comb at 3.0 THz based on difference-frequency generation from a mid-IR QCL comb. A largely detuned distributed-feedback grating is integrated into the QCL cavity to provide the single mode operation as well as enhanced spatial hole-burning effect for multimode comb operation. Multiheterodyne spectroscopy with multiple equally spaced lines by beating it with a reference Fabry-Pérot comb confirms the THz comb operation. This type of THz comb provides a new solution to chip-based high-speed high-resolution THz spectroscopy with compact size at room temperature. [reprint (PDF)]
11.	Quantum dot in a well infrared photodetectors for high operating temperature focal plane arrays S. Tsao, T. Yamanaka, S. Abdollahi Pour, I-K Park, B. Movaghar and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7234-0V-- January 25, 2009 ...[Visit Journal] InAs quantum dots embedded in InGaAs quantum wells with InAlAs barriers on InP substrate grown by metalorganic chemical vapor deposition are utilized for high operating temperature detectors and focal plane arrays in the middle wavelength infrared. This dot-well combination is unique because the small band offset between the InAs dots and the InGaAs well leads to weak dot confinement of carriers. As a result, the device behavior differs significantly from that in the more common dot systems that have stronger confinement. Here, we present energy level modeling of our QD-QW system and apply these results to interpret the detector behavior. Detectors showed high performance with D* over 10¹⁰ cm·Hz^1/2W^-1 at 150 K operating temperature and with high quantum efficiency over 50%. Focal plane arrays have been demonstrated operating at high temperature due to the low dark current observed in these devices. [reprint (PDF)]
11.	Recent advances in III-Nitride materials, characterization and device applications M. Razeghi, X. Zhang, P. Kung, A. Saxler, D. Walker, K.Y. Lim, and K.S. Kim SPIE Conference: Solid State Crystals in Optoelectronics and Semiconductor Technology; Proceedings 3179-- October 7, 1996 ...[Visit Journal] High-quality AlN, GaN, AlGaN have been grown on sapphire substrate by low-pressure metalorganic chemical vapor deposition (LP-MOCVD). The x-ray rocking curve of AlN and GaN were 100 arcsecs and 30 arcsecs respectively with Pendelloesung oscillations, which are the best reported to date. GaN with high crystallinity simultaneously exhibited high optical and electrical quality. Photoluminescence linewidth of GaN at 77K was as low as 17 meV, which is the best reported to date. Si-doped GaN had a mobility higher than 300 cm²/V·s. GaN has been also successfully grown on LiGaO₂ substrate with LP-MOCVD for the first time. AlGaN for the entire composition range has been grown. These layers exhibited the lowest x-ray FWHM reported to date. The excellent optical quality of these layers have been characterized by room temperature UV transmission and photoluminescence. N-type doping of AlGaN with Si has ben achieved up to 60 percent Al with mobility as high as 78 cm²/V·s. Al_xGa_1-xN/Al_yGa_1-yN superlattice with atomically sharp interface have been demonstrated. Optically-pumped stimulated emission in GaN:Ge and GaN:Si has been observed with threshold optical power density as low as 0.4 MW/cm². AlGaN photoconductors with cut-off wavelengths from 200 nm to 365 nm have been achieved for the first time. GaN p-n junction photovoltaic detector with very selective photoresponse have been demonstrated and theoretically modeled. Ti/AlN/Si metal-insulator- semiconductor capacitor with high capacitance-voltage performances at both low and high frequencies and low interface trap level density have been demonstrated for the first time in this material system. [reprint (PDF)]
11.	Electrical Characterization of Al_xGa_1-xN for UV Photodetector Applications A. Saxler, M. Ahoujja, W.C. Mitchel, P. Kung, D. Walker, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] Ultraviolet photodetectors have many military and commercial applications. However, for many of these applications, the photodetectors must be solar blind. This means that the photodetectors must have a cutoff wavelength of less than about 270 nm. Semiconductor based devices would then need energy gaps of over 4.6 eV. In the Al_xGa_1-xN system, the aluminum mole fraction, x, required is over 40%. As the energy gap is increased, doping becomes much more difficult, especially p-type doping. This report is a study of the electrical properties of Al_xGa_1-xN to enable better control of the doping. Magnesium doped p-type Al_xGa_1-xN has been studied using high-temperature Hall effect measurements. The acceptor ionization energy has been found to increase substantially with the aluminum content. Short-period superlattices consisting of alternating layers of GaN:Mg and AlGaN:Mg were also grown by low-pressure organometallic vapor phase epitaxy. The electrical properties of these superlattices were measured as a function of temperature and compared to conventional AlGaN:Mg layers. It is shown that the optical absorption edge can be shifted to shorter wavelengths while lowering the acceptor ionization energy by using short- period superlattice structures instead of bulk-like AlGaN:Mg. Silicon doped n-type films have also been studied. [reprint (PDF)]
11.	EPR investigation of Gd3+ and Eu2+ in the α- and β-phases of lead phosphate M. RAZEGHI, J. P. BUISSON, and B. HOULIE M. RAZEGHI et al.: EPR Investigation of Gd3+ and Eu2+ in Lead Phosphate phys. stat. sol. (b) 96, 283 (1979-- September 1, 1979 ...[Visit Journal] The X-band EPR spectra of Gd3+and Eu2+diluted in Pb3(P04)2crystals are studied. Lead phos-phate exhibits a ferroelastic phase transition a t 180 “C and the EPR spectra obtained in eachphase differ from each other. The spectra are very complex because the zero field splitting hasthe same order of magnitude as the Zeeman term. The spin Hamiltonian parameters and theenergy levels are computed. “Forbidden” or “missing” transitions and line intensities can beexplained. [reprint (PDF)]
11.	RT-CW: widely tunable semiconductor THz QCL sources M. Razeghi; Q. Y. Lu Proceedings Volume 9934, Terahertz Emitters, Receivers, and Applications -- September 26, 2016 ...[Visit Journal] Distinctive position of Terahertz (THz) frequencies (ν~0.3 -10 THz) in the electromagnetic spectrum with their lower quantum energy compared to IR and higher frequency compared to microwave range allows for many potential applications unique to them. Especially in the security side of the THz sensing applications, the distinct absorption spectra of explosives and related compounds in the range of 0.1–5 THz makes THz technology a competitive technique for detecting hidden explosives. A compact, high power, room temperature continuous wave terahertz source emitting in a wide frequency range will greatly boost the THz applications for the diagnosis and detection of explosives. Here we present a new strong-coupled strain-balanced quantum cascade laser design for efficient THz generation based intracavity DFG. Room temperature continuous wave operation with electrical frequency tuning range of 2.06-4.35 THz is demonstrated [reprint (PDF)]
11.	Hole-initiated multiplication in back-illuminated GaN avalanche photodiodes R. McClintock, J.L. Pau, K. Minder, C. Bayram, P. Kung and M. Razeghi Applied Physics Letters, Vol. 90 No. 14, p. 141112-1-- April 2, 2007 ...[Visit Journal] Avalanche p-i-n photodiodes were fabricated on AlN templates for back illumination. Structures with different intrinsic layer thicknesses were tested. A critical electric field of 2.73 MV/cm was estimated from the variation of the breakdown voltage with thickness. From the device response under back and front illumination and the consequent selective injection of holes and electrons in the junction, ionization coefficients were obtained for GaN. The hole ionization coefficient was found to be higher than the electron ionization coefficient as predicted by theory. Excess multiplication noise factors were also calculated for back and front illumination, and indicated a higher noise contribution for electron injection. [reprint (PDF)]
11.	GaInAsP/InP 1.35 μm Double Heterostructure Laser Grown on Silicon Substrate by Metalorganic Chemical Vapor Deposition K. Mobarhan, C. Jelen, E. Kolev, and M. Razeghi Journal of Applied Physics 74 (1)-- July 1, 1993 ...[Visit Journal] A 1.35 μm GaInAsP/InP double heterostructure laser has been grown on a Si substrate using low‐pressure metalorganic chemical vapor deposition. This was done without the use of a superlattice layer or a very thick InP buffer layer, which are used to prevent the dislocations from spreading into the active layer. Pulsed operation with output power of over 200 mW per facet was achieved at room temperature for broad area lasers with 20 μm width and 170 μm cavity length. The threshold current density of a 350 μm cavity length device was 9.8 kA/cm². The characteristic temperature was 66 K. [reprint (PDF)]
11.	High peak power 16 m InP-related quantum cascade laser A. Szerlinga,∗, S. Slivkenb, M. RazeghibaInstytut Opto-Electronics Review 25, pp. 205–208-- July 22, 2017 ...[Visit Journal] tIn this paper ∼16 μm-emitting multimode InP-related quantum cascade lasers are presented with themaximum operating temperature 373 K, peak and average optical power equal to 720 mW and 4.8 mW at 303 K, respectively, and the characteristic temperature (T₀) 272 K. Two types of the lasers were fabricatedand characterized: the lasers with a SiO₂ layer left untouched in the area of the metal-free window ontop of the ridge, and the lasers with the SiO₂layer removed from the metal-free window area. Dual-wavelength operation was obtained, at ∼15.6 μm (641 cm⁻¹) and at ∼16.6 μm (602 cm⁻¹) for laserswith SiO₂-removed, while within the emission spectrum of the lasers with SiO₂-left untouched only the former lasing peak was present. The parameters of these devices like threshold current, optical power and emission wavelength are compared. Lasers without the SiO₂ layer showed ∼15% lower threshold current than these ones with the SiO₂ layer. The optical powers for lasers without SiO₂ layer were almost twice higher than for the lasers with the SiO₂ layer on the top of the ridge. [reprint (PDF)]
11.	Current status and potential of high power mid-infrared intersubband lasers S. Slivken, Y. Bai, B. Gokden, S.R. Darvish and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7608, p. 76080B-1-- January 22, 2010 ...[Visit Journal] Some of the recent advances in high power quantum cascade laser development will be reviewed in this paper. Research areas explored include short wavelength (λ <4 µm) lasers, high performance strain-balanced heterostructures, and high power long wavelength (7< λ< 16 µm) lasers. Near λ=4.5 µm, highlights include demonstration of 18% continuous wave wallplug efficiency at room temperature, 53% pulsed wallplug efficiency at 40 K, and 120 W of peak power output from a single device at room temperature. Near λ ~10 µm, up to 0.6 W of continuous output power at room temperature has also been demonstrated, with pulsed efficiencies up to 9%. [reprint (PDF)]
11.	Passivation of Type-II InAs/GaSb Superlattice Photodiodes A. Gin, Y. Wei, J. Bae, A. Hood, J. Nah, and M. Razeghi International Conference on Metallurgical Coatings and Thin Films (ICMCTF), San Diego, CA; Thin Solid Films 447-448-- January 30, 2004 ...[Visit Journal] Recently, excellent infrared detectors have been demonstrated using Type-II InAs/GaSb superlattice materials sensitive at wavelengths from 3 μm to greater than 32 μm. These results indicate that Type-II superlattice devices may challenge the preponderance of HgCdTe and other state-of-the-art infrared material systems. As such, surface passivation is becoming an increasingly important issue as progress is made towards the commercialization of Type-II devices and focal plane array applications. This work focuses on initial attempts at surface passivation of Type-II InAs/GaSb superlattice photodiodes using PECVD-grown thin layers of SiO₂. Our results indicate that silicon dioxide coatings deposited at various temperatures improve photodetector resistivity by several times. Furthermore, reverse-bias dark current has been reduced significantly in passivated devices. [reprint (PDF)]
11.	Advances in UV sensitive visible blind GaN-based APDs M. Ulmer, R. McClintock and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-27, 2011), Vol. 7945, p. 79451G-- January 23, 2011 ...[Visit Journal] In this paper, we describe our current state-of-the-art process of making visible-blind APDs based on GaN. We have grown our material on both conventional sapphire and low dislocation density free-standing c- and m-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs are compared. The spectral response and Geiger-mode photon counting performance of UV APDs are studied under low photon fluxes. Single photon detection capabilities with over 30% are demonstrated. We show how with pulse height discrimination the Geiger-mode operation conditions can be optimized for enhanced SPDE versus dark counts. [reprint (PDF)]
11.	Growth and characterization of InSbBi for long wavelength infrared photodetectors J.J. Lee, J.D. Kim, and M. Razeghi Applied Physics Letters 70 (24)-- June 16, 1997 ...[Visit Journal] The epitaxial growth of InSbBi ternary alloys by low-pressure metalorganic chemical vapor deposition is reported on. X-ray diffraction spectra showed well resolved peaks of InSbBi and InSb films. Bi incorporation was confirmed by energy dispersive x-ray analysis. Photoresponse spectrum up to 9.3 μm which corresponds to 0.13 eV energy band gap has been measured in a sample with Bi composition of 5.8 at.% at 77 K. Electron mobility at room temperature ranges from 44 100 to 4910 cm²/V·s as Bi composition increases. [reprint (PDF)]
11.	Nanoselective area growth of defect-free thick indium-rich InGaN nanostructures on sacriﬁcial ZnO templates Renaud Puybaret, David J Rogers, Youssef El Gmili, Suresh Sundaram, Matthew B Jordan, Xin Li, Gilles Patriarche, Ferechteh H Teherani, Eric V Sandana, Philippe Bove, Paul L Voss, Ryan McClintock, Manijeh Razeghi, Ian Ferguson, Jean-Paul Salvestrini, and Abdallah Ougazzade Nanotechnology 28 195304-- April 29, 2017 ...[Visit Journal] Nanoselective area growth (NSAG) by metal organic vapor phase epitaxy of high-quality InGaN nanopyramids on GaN-coated ZnO/c-sapphire is reported. Nanopyramids grown on epitaxial low-temperature GaN-on-ZnO are uniform and appear to be single crystalline, as well as free of dislocations and V-pits. They are also indium-rich (with homogeneous 22% indium incorporation) and relatively thick (100 nm). These properties make them comparable to nanostructures grown on GaN and AlN/Si templates, in terms of crystallinity, quality, morphology, chemical composition and thickness. Moreover, the ability to selectively etch away the ZnO allows for the potential lift-off and transfer of the InGaN/GaN nanopyramids onto alternative substrates, e.g. cheaper and/or ﬂexible. This technology offers an attractive alternative to NSAG on AlN/Si as a platform for the fabrication of high quality, thick and indium-rich InGaN monocrystals suitable for cheap, ﬂexible and tunable light-emitting diodes. [reprint (PDF)]
11.	Low irradiance background limited type-II superlattice MWIR M-barrier imager E.K. Huang, S. Abdollahi Pour, M.A. Hoang, A. Haddadi, M. Razeghi and M.Z. Tidrow OSA Optics Letters (OL), Vol. 37, No. 11, p. 2025-2027-- June 1, 2012 ...[Visit Journal] We report a type-II superlattice mid-wave infrared 320 × 256 imager at 81 K with the M-barrier design that achieved background limited performance (BLIP) and ∼99%operability. The 280 K blackbody’s photon irradiance was limited by an aperture and a band-pass filter from 3.6 μm to 3.8 μm resulting in a total flux of ∼5 × 10¹² ph·cm⁻²·s⁻¹. Under these low-light conditions, and consequently the use of a 13.5 ms integration time, the imager was observed to be BLIP thanks to a ∼5 pA dark current from the 27 μm wide pixels. The total noise was dominated by the photon flux and read-out circuit which gave the imager a noise equivalent input of ∼5 × 10¹⁰ ph·cm⁻²·s⁻¹ and temperature sensitivity of 9 mK with F∕2.3 optics. Excellent imagery obtained using a 1-point correction alludes to the array’s uniform responsivity. [reprint (PDF)]
11.	A lifetime of contributions to the world of semiconductors using the Czochralski invention Manijeh Razeghi Journal of Vacuum Volume 146, Pages 308-328-- December 1, 2017 ...[Visit Journal] Over the course of my career, I have made numerous contributions related to semiconductor crystal growth and high performance optoelectronics over a vast region of the electromagnetic spectrum (ultraviolet to terahertz). In 2016 this cumulated in my receiving the Jan Czochralski Gold Medal award from the European Materials Research Society. This article is designed to provide a historical perspective and general overview of these scientific achievements, on the occasion of being honored by this award. These achievements would not have been possible without high quality crystalline substrates, and this article is written in honor of Jan Czochralski on the 100th anniversary of his important discovery. [reprint (PDF)]
11.	Thermal analysis of buried heterostructure quantum cascade lasers for long-wavelength infrared emission using 2D anisotropic heat-dissipation model H.K. Lee, K.S. Chung, J.S. Yu and M. Razeghi Physica Status Solidi (a), Vol. 206, p. 356-362-- February 1, 2009 ...[Visit Journal] We have theoretically investigated and compared the thermal characteristics of 10.6 μm InGaAs/InAlAs/InP buried heterostructure (BH) quantum cascade lasers (QCLs) with different heat-sinking configurations by a steady-state heat-transfer analysis. The heat-source densities were obtained from laser threshold power densities measured experimentally under room-temperature continuous-wave mode. The two-dimensional anisotropic heat-dissipation model was used to calculate the temperature distribution, heat flux, and thermal conductance (Gth) inside the device. For good thermal characteristics, the QCLs in the long-wavelength infrared region require the relatively narrow BH structure in combination with epilayer-down bonding due to thick active core/cladding layers and high insulator losses. The single-ridge BH structure results in slightly higher thermal conductance by 2-4% than the double-channel (DC) ridge BH structure. For W = 12 m with 5 μm thick electroplated Au, the single-ridge BH laser with epilayer-down bonding exhibited the highest G_th value of 201.9 W/K cm², i.e. increased by nearly 36% with respect to the epilayer-up bonded DC ridge waveguide laser. This value is improved by 50% and 62% with respect to the single-ridge BH laser and DC ridge waveguide laser with W = 20 μm in the epilayer-up bonding scheme, respectively. [reprint (PDF)]
11.	Schottky barrier heights and conduction-band offsets of In_1-xGa_xAs_1-yP_y lattice matched to GaAs J.K. Lee, Y.H. Cho, B.D. Choe, K.S. Kim, H.I. Jeon, H. Lim and M. Razeghi Applied Physics Letters 71 (7)-- August 18, 1997 ...[Visit Journal] The Schottky barrier heights of Au/In_1−xGa_xAs_1−yP_y contacts have been determined as a function of y by the capacitance–voltage and temperature dependent current–voltage characteristics measurements. The barrier height is observed to increase as y is increased for both n- and p-type materials, with a more rapid increase for the p-type material. The compositional variation of the barrier heights for Au/n-In_1−xGa_xAs_1−yP_y is found to be identical to that of the conduction-band offsets in In_1−xGa_xAs_1−yP_y/GaAs heterojunctions. A possible cause of this phenomenon is also discussed. [reprint (PDF)]
11.	Scaling in back-illuminated GaN avalanche photodiodes K. Minder, J.L. Pau, R. McClintock, P. Kung, C. Bayram, M. Razeghi and D. Silversmith Applied Physics Letters, Vol. 91, No. 7, p. 073513-1-- August 13, 2007 ...[Visit Journal] Avalanche p-i-n photodiodes of various mesa areas were fabricated on AlN templates for back illumination for enhanced performance through hole-initiated multiplication, and the effects of increased area on device performance were studied. Avalanche multiplication was observed in mesa sizes up to 14,063 µm^2 under linear mode operation. Uniform gain and a linear increase of the dark current with area were demonstrated. [reprint (PDF)]

Page 28 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)