Center for Quantum Devices - Most Downloaded Journal Articles

Page 25 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

12.	Photoluminescence study of InAsSb/InAsSbP heterostructures grown by low-pressure metalorganic chemical vapor deposition S. Kim, M. Erdtmann, D. Wu, E. Kaas, H. Yi, J. Diaz, and M. Razeghi Applied Physics Letters 69 (11)-- September 9, 1996 ...[Visit Journal] Photoluminescence has been measured for double‐ and separate‐confinement InAsSb/InAsSbP heterostructures grown by low‐pressure metalorganic vapor deposition. A measurement of the integrated luminescence intensity at the temperature range of 77–300 K shows that over a wide range of excitation level (1–5×10² W/cm²) the radiative transitions are the dominant. mechanism below T∼170 K. Auger recombination coefficient C=C₀ exp(−E_a/kT) with C₀≊5×10⁻²⁷ cm⁶/s and E_a≊40 meV has been estimated. [reprint (PDF)]
12.	Cavity Length Effects of High-Temperature High-Power Continuous Wave Characteristics in Quantum-Cascade Lasers J.S. Yu, A. Evans, J. David, L. Doris, S. Slivken, and M. Razeghi Applied Physics Letters, 83 (25)-- December 22, 2003 ...[Visit Journal] We report the cavity-length dependent high-temperature high-power cw characteristics in λ=6 µm quantum-cascade lasers with a thick electroplated Au top contact layer. For a high-reflectivity (HR) coated 15 µm wide and 3 mm long laser, the cw operation is achieved up to 313 K (40 °C) with an output power of 17 mW. At 298 K, a very high cw output power of 213 mW is obtained for a HR coated 15 µm wide and 4 mm long laser. Thermal resistance is analyzed at temperatures above 283 K for HR coated lasers with different cavities. [reprint (PDF)]
12.	High-performance InAs quantum-dot infrared photodetectors grown on InP substrate operating at room temperature H. Lim, S. Tsao, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 90, No. 13, p. 131112-1-- March 26, 2007 ...[Visit Journal] The authors report a room temperature operating InAs quantum-dot infrared photodetector grown on InP substrate. The self-assembled InAs quantum dots and the device structure were grown by low-pressure metal-organic chemical vapor deposition. The detectivity was 2.8×10¹¹ cm·Hz^1/2/W at 120 K and a bias of −5 V with a peak detection wavelength around 4.1 μm and a quantum efficiency of 35%. Due to the low dark current and high responsivity, a clear photoresponse has been observed at room temperature, which gives a detectivity of 6.7×10⁷ cm·Hz^1/2/W. [reprint (PDF)]
12.	High-responsivity GaInAs/InP Quantum Well Infrared Photodetectors Grown by Low-Pressure Metalorganic Chemical Vapor Deposition M. Erdtmann, A. Matlis, C. Jelen, M. Razeghi, and G. Brown SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] We have studied the dependence of the well doping density in n-type GaInAs/InP quantum well IR photodetectors (QWIPs) grown by low-pressure metalorganic chemical vapor deposition. Three identical GaInAs/InP QWIP structures were grown with well sheet carrier densities of 1x10¹¹ cm^-2, 3x10¹¹ cm^-2, and 10x10¹¹ cm^-2; all three samples had very sharp spectral response at λ equals 9.0 μm. We find that there is a large sensitivity of responsivity, dark current, noise current, and detectivity with the well doping density. Measurements revealed that the lowest-doped samples had an extremely low responsivity relative to the doping concentration while the highest-doped sample had an excessively high dark current relative to doping. The middle-doped sample yielded the optimal results. This QWIP had a responsivity of 33.2 A/W and operated with a detectivity of 3.5x10¹⁰ cm·Hz^½·W^-1 at a bias of 0.75 V and temperature of 80 K. This responsivity is the highest value reported for any QWIP in the (lambda) equals 8-9 &mus;m range. Analysis is also presented explaining the dependence of the measured QWIP parameters to well doping density. [reprint (PDF)]
12.	Recent advances in LWIR type-II InAs/GaSb superlattice photodetectors and focal plane arrays at the Center for Quantum Devices M. Razeghi, D. Hoffman, B.M. Nguyen, P.Y. Delaunay, E.K. Huang, and M.Z. Tidrow SPIE Porceedings, Vol. 6940, Orlando, FL 2008, p. 694009-- March 17, 2008 ...[Visit Journal] In recent years, Type-II InAs/GaSb superlattice photo-detectors have experienced significant improvements in material quality, structural designs, and imaging applications. They now appear to be a possible alternative to the state-of-the-art HgCdTe (MCT) technology in the long and very long wavelength infrared regimes. At the Center for Quantum Devices,we have successfully realized very high quantum efficiency, very high dynamic differential resistance R0A - product LWIR Type – II InAs/GaSb superlattice photodiodes with efficient surface passivation techniques. The demonstration of high quality LWIR Focal Plane Arrays that were 100 % fabricated in - house reaffirms the pioneer position of this university-based laboratory. [reprint (PDF)]
12.	Growth and Characterization of Type-II Non-Equilibrium Photovoltaic Detectors for Long Wavelength Infrared Range H. Mohseni, J. Wojkowski, A. Tahraoui, M. Razeghi, G. Brown and W. Mitche SPIE Conference, San Jose, CA, -- January 26, 2000 ...[Visit Journal] Growth and characterization of type-II detectors for mid-IR wavelength range is presented. The device has a p-i-n structure is designed to operate in the non-equilibrium mode with low tunneling current. The active layer is a short period InAs/GaSb superlattice. Wider bandgap p-type AlSb and n-type InAs layers are used to facilitate the extraction of both electronics and holes from the active layer for the first time. The performance of these devices were compared to the performance of devices grown at the same condition, but without the AlSb barrier layers. The processed devices with the AlSb barrier show a peak responsivity of about 1.2 A/W with Johnson noise limited detectivity of 1.1 X 10¹¹ cm·Hz^½/W at 8 μm at 80 K at zero bias. The details of the modeling, growth, and characterizations will be presented. [reprint (PDF)]
12.	Impact of scaling base thickness on the performance of heterojunction phototransistors Arash Dehzangi, Abbas Haddadi, Sourav Adhikary, and Manijeh Razeghi Nanotechnology 28, 10LT01-- February 2, 2017 ...[Visit Journal] In this letter we report the effect of vertical scaling on the optical and electrical performance of mid-wavelength infrared heterojunction phototransistors based on type-II InAs/GaSb/AlSb superlattices. The performance of devices with different base thickness was compared as the base was scaled from 60 down to 40 nm. The overall optical performance shows enhancement in responsively, optical gain, and specific detectivity upon scaling the base width. The saturated responsivity for devices with 40 nm bases reaches 8,845 and 9,528 A/W at 77 and 150 K, respectively, which is almost five times greater than devices with 60 nm bases. The saturated optical gain for devices with 40 nm bases is measured as 2,760 at 77 K and 3,081 at 150 K. The devices with 40 nm bases also exhibit remarkable enhancement in saturated current gain, with 17,690 at 77 K, and 19,050 at 150 K. [reprint (PDF)]
12.	High power photonic crystal distributed feedback quantum cascade lasers emitting at 4.5 micron B. Gokden, S. Slivken and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7608, p. 760806-1-- January 22, 2010 ...[Visit Journal] Quantum cascade lasers possess very small linewidth enhancement factor, which makes them very prominent candidates for realization of high power, nearly diffraction limited and single mode photonic crystal distributed feedback broad area lasers in the mid-infrared frequencies. In this paper, we present room temperature operation of a two dimensional photonic crystal distributed feedback quantum cascade laser emitting at 4.5 µm. peak power up to ~0.9 W per facet is obtained from a 2 mm long laser with 100 µm cavity width at room temperature. The observed spectrum is single mode with a very narrow linewidth. Far-field profile has nearly diffraction limited single lobe with full width at half maximum of 3.5 degree normal to the facet. The mode selection and power output relationships are experimentally established with respect to different cavity lengths for photonic crystal distributed feedback quantum cascade lasers. [reprint (PDF)]
12.	Electron spin resonance in the two-dimensional electron gas of a GaAs-Gax In1-xP heterostructure M DoberstS, J P Vierent, M RazeghiS, M DefourS and F Ornnes Semicond. Sci. Technol. 4 (1989) 687-690-- June 12, 1989 The microwave-induced change of the magnetoresistivity of GaAs-GalnP heterostructures reveals resonant structure which is attributed to electron spin resonance of the two-dimensional conduction electrons. The spin splitting of the two lowest Landau levels has been investigated as a function of the magnetic field. From these studies we obtain the dependence of the g-factor on the magnetic field and the Landau level. These results are compared with those obtained in GaAs-AIGaAs heterostructures. [reprint (PDF)]
12.	MOCVD Growth of ZnO Nanostructures Using Au Droplets as Catalysts V.E. Sandana, D.J. Rogers, F.H. Teherani, R. McClintock, M. Razeghi, H.J. Drouhin, M.C. Clochard, V. Sallett, G. Garry and F. Fayoud SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Zinc Oxide Materials and Devices III, Vol. 6895, p. 68950Z-1-6.-- February 1, 2008 ...[Visit Journal] ZnO nanostructures were synthesised by Metal Organic Chemical Vapor Deposition growth on Si (100) and c-Al₂O₃ substrates coated with a 5nm thick layer of Au. The Au coated substrates were annealed in air prior to deposition of ZnO so as to promote formation of Au nanodroplets. The development of the nanodroplets was studied as a function of annealing duration and temperature. Under optimised conditions, a relatively homogeneous distribution of regular Au nanodroplets was obtained. Using the Au nanodroplets as a catalyst, MOCVD growth of ZnO nanostructures was studied. Scanning electron microscopy revealed nanostructures with various forms including commonly observed structures such as nanorods, nanoneedles and nanotubes. Some novel nanostructures were also observed, however, which resembled twist pastries and bevelled-multifaceted table legs. [reprint (PDF)]
12.	Tunability of intersubband absorption from 4.5 to 5.3 µm in a GaN/Al_0.2Ga_0.8N superlattices grown by metalorganic chemical vapor deposition N. Péré-Laperne, C. Bayram, L. Nguyen-Thê, R. McClintock, and M. Razeghi Applied Physics Letters, Vol. 95, No. 13, p. 131109-- September 28, 2009 ...[Visit Journal] Intersubband (ISB) absorption at wavelengths as long as 5.3 µm is realized in GaN/Al_0.2Ga_0.8N superlattices grown by metalorganic chemical vapor deposition. By employing low aluminum content Al_0.2Ga_0.8N barriers and varying the well width from 2.6 to 5.1 nm, ISB absorption has been tuned from 4.5 to 5.3 µm. Theoretical ISB absorption and interband emission models are developed and compared to the experimental results. The effects of band offsets and the piezoelectric fields on these superlattices are investigated. [reprint (PDF)]
12.	First GaInAsP‐InP double‐heterostructure laser emitting at 1.27 μm on a silicon substrate M. Razeghi; M. Defour; F. Omnes; Ph. Maurel; J. Chazelas; F. Brillouet Appl. Phys. Lett. 53, 725–727 (1988)-- June 21, 1988 ...[Visit Journal] We report the first successful room-temperature GalnAsP-InP double-heterostructure laser emitting at 1.27 pm, grown by low-pressure metalorganic chemical vapor deposition on a Si substrate. A pulsed threshold current density of 10 kAlcm2 at room temperature with an external quantum efficiency of 10% per facet and an output power of20 mW (for an oxidedefined stripe geometry with 12 pm stripe width and 250 pm cavity length) has been measured. The first aging test in pulse operation shows an increase of threshold current of only 7% for a cumulative time of 80 s at room temperature. [reprint (PDF)]
12.	Mid-infrared quantum cascade lasers with high wall plug efficiency Y. Bai, B. Gokden, S. Slivken, S.R. Darvish, S.A. Pour, and M. Razeghi SPIE Proceedings, San Jose, CA Volume 7222-0O-- January 26, 2009 ...[Visit Journal] We demonstrate optimization of continuous wave (cw) operation of 4.6 µm quantum cascade lasers (QCLs). A 19.7 µm by 5 mm, double channel processed device exhibits 33% cw WPE at 80 K. Room temperature cw WPE as high as 12.5% is obtained from a 10.6 µm by 4.8 mm device, epilayer-down bonded on a diamond submount. With the semi-insulating regrowth in a buried ridge geometry, 15% WPE is obtained with 2.8 W total output power in cw mode at room temperature. This accomplishment is achieved by systematically decreasing the parasitic voltage drop, reducing the waveguide loss and improving the thermal management. [reprint (PDF)]
12.	High Power 3-12 μm Infrared Lasers: Recent Improvements and Future Trends M. Razeghi, S. Slivken, A. Tahraoui, A. Matlis, and Y.S. Park Physica E: Low-Dimensional Systems and Nanostructures 11 (2-3)-- October 1, 2001 ...[Visit Journal] In this paper, we discuss the progress of quantum cascade lasers (QCLs) grown by gas-source molecular beam epitaxy. Room temperature QCL operation has been reported for lasers emitting between 5-11 μm, with 9-11 μm lasers operating up to 425 K. Laser technology for the 3-5 μm range takes advantage of a strain-balanced active layer design. We also demonstrate record room temperature peak output powers at 9 and 11 μm (2.5 and 1 W, respectively) as well as record low 80K threshold current densities (250 A/cm²) for some laser designs. Preliminary distributed feedback (DFB) results are also presented and exhibit single mode operation for 9 μm lasers at room temperature. [reprint (PDF)]
12.	Status of III-V semiconductor thin films and their applications to future OEICs Manijeh Razeghi Proc. SPIE 10267, Integrated Optics and Optoelectronics, 102670T -- June 26, 2017 ...[Visit Journal] In the last decade, semiconductor technology has been advanced to a great extent in terms of electronic and photonic discrete devices. One of the main reasons for such a progress, is the result of advancement in the epitaxial growth techniques such as molecular beam epitaxy (MBE) and metalorganic chemical vapor deposition (MOCVD), where device quality films can be grown with great control over composition, uniformity and thickness. MOCVD has proven to be one of the best growth methods for many IH-V semiconductor thin films 1. Its flexibility and potential to yield a broad range of growth rates resulted in the layers featuring the thicknesses from tens of microns down to several nanometers. Planar structures containing quantum wells with atomically flat interfaces, superlattices, strained or graded-index layers were successfully grown by MOCVD. Furthermore, MOCVD proved its efficiency in producing a laser devices by overgrowth and epitaxy on patterned substrates. The importance of MOCVD is strongly enhanced by the possibility of large-scale production by simultaneous growth on several substrates in one process. Several III-V semiconductor films with bandgaps ranging from infrared to ultraviolet (15 to 0.2 μm) have been successfully grown by MOCVD. [reprint (PDF)]
12.	Molecular Beam Epitaxial Growth of High Quality InSb E. Michel, G. Singh, S. Slivken, C. Besikci, P. Bove, I. Ferguson, and M. Razeghi Applied Physics Letters 65 (26)-- December 26, 1994 ...[Visit Journal] In this letter we report on the growth of high quality InSb by molecular beam epitaxy that has been optimized using reflection high energy electron diffraction. A 4.8 µm InSb layer grown on GaAs at a growth temperature of 395 °C and a III/V incorporation ratio of 1:1.2 had an x-ray rocking curve of 158 arcsec and a Hall mobility of 92,300 cm²·V⁻¹ at 77 K. This is the best material quality obtained for InSb nucleated directly onto GaAs reported to date. [reprint (PDF)]
12.	Geiger-mode operation of ultraviolet avalanche photodiodes grown on sapphire and free-standing GaN substrates E. Cicek, Z. Vashaei, R. McClintock, C. Bayram, and M. Razeghi Applied Physics Letters, Vol. 96, No. 26, p. 261107 (2010);-- June 28, 2010 ...[Visit Journal] GaN avalanche photodiodes (APDs) were grown on both conventional sapphire and low dislocation density free-standing (FS) c-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs were compared. At a reverse-bias of 70 V, APDs grown on sapphire substrates exhibited a dark current density of 2.7×10⁻⁴ A/cm² whereas APDs grown on FS-GaN substrates had a significantly lower dark current density of 2.1×10⁻⁶ A/cm². Under linear-mode operation, APDs grown on FS-GaN achieved avalanche gain as high as 14 000. Geiger-mode operation conditions were studied for enhanced SPDE. Under front-illumination the 625 μm² area APD yielded a SPDE of 13% when grown on sapphire substrates compared to more than 24% when grown on FS-GaN. The SPDE of the same APD on sapphire substrate increased to 30% under back-illumination—the FS-GaN APDs were only tested under front illumination due to the thick absorbing GaN substrate. [reprint (PDF)]
12.	High-Performance Focal Plane Arrays Based on InAs-GaSb Superlattices with a 10-micron Cutoff Wavelegth P.Y. Delaunay, B.M. Nguyen, D. Hoffman and M. Razeghi IEEE Journal of Quantum Electronics, Vol. 44, No. 5, p. 462-467-- May 1, 2008 ...[Visit Journal] We report on the demonstration of a focal plane array based on Type-II InAs/GaSb superlattices grown on N-type GaSb substrate with a 50%-cutoff wavelength at 10 μm. The surface leakage occurring after flip-chip bonding and underfill in the Type-II devices was suppressed using a double heterostructure design. The R₀A of diodes passivated with SiO₂ was 23 Ω·cm² after underfill. A focal plane array hybridized to an Indigo readout integrated circuit demonstrated a noise equivalent temperature difference of 33 mK at 81 K, with an integration time of 0.23 ms. [reprint (PDF)]
12.	High power, continuous wave, quantum cascade ring laser Y. Bai, S. Tsao, N. Bandyopadhyay, S. Slivken, Q.Y. Lu, D. Caffey, M. Pushkarsky, T. Day and M. Razeghi Applied Physics Letters, Vol. 99, No. 26, p. 261104-1-- December 26, 2011 ...[Visit Journal] We demonstrate a quantum cascade ring laser with high power room temperature continuous wave operation. A second order distributed feedback grating buried inside the waveguide provides both in-plane feedback and vertical power outcoupling. Total output power reaches 0.51 W at an emission wavelength around 4.85 μm. Single mode operation persists up to 0.4 W. The far field analysis indicates that the device operates in a high order mode. The magnetic and electric components of the ring-shaped lasing beam are in radial and azimuthal directions, respectively. [reprint (PDF)]
12.	High operating temperature 320 x 256 middle-wavelength infrared focal plane array imaging based on an InAs/InGaAs/InAlAs/InP quantum dot infrared photodetector S. Tsao, H. Lim, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 90, No. 20, p. 201109-- May 14, 2007 ...[Visit Journal] This letter reports a 320×256 middle-wavelength infrared focal plane array operating at temperatures up to 200 K based on an InAs quantum dot/InGaAs quantum well/InAlAs barrier detector grown on InP substrate by low pressure metal organic chemical vapor deposition. The device's low dark current density and the persistence of the photocurrent up to room temperature enabled the high temperature imaging. The focal plane array had a peak detection wavelength of 4 µm, a responsivity of 34 mA/W, a conversion efficiency of 1.1%, and a noise equivalent temperature difference of 344 mK at an operating temperature of 120 K. [reprint (PDF)]
12.	Continuous-wave operation of λ ~ 4.8 µm quantum-cascade lasers at room temperature A. Evans, J.S. Yu, S. Slivken, and M. Razeghi Applied Physics Letters, 85 (12)-- September 20, 2004 ...[Visit Journal] Continuous-wave (cw) operation of quantum-cascade lasers emitting at λ~4.8 µm is reported up to a temperature of 323 K. Accurate control of layer thickness and strain-balanced material composition is demonstrated using x-ray diffraction. cw output power is reported to be in excess of 370 mW per facet at 293 K, and 38 mW per facet at 323 K. Room-temperature average power measurements are demonstrated with over 600 mW per facet at 50% duty cycle with over 300 mW still observed at 100% (cw) duty cycle. [reprint (PDF)]
12.	Comparison of ultraviolet light-emitting diodes with peak emission at 340 nm grown on GaN substrate and sapphire A. Yasan, R. McClintock, K. Mayes, S.R. Darvish, H. Zhang, P. Kung, M. Razeghi, S.K. Lee and J.Y. Han Applied Physics Letters, 81 (12)-- September 16, 2002 ...[Visit Journal] Based on AlInGaN/AlInGaN multiquantum wells, we compare properties of ultraviolet light-emitting diodes (LED) with peak emission at 340 nm grown on free-standing hydride vapor phase epitaxially grown GaN substrate and on sapphire. For the LED grown on GaN substrate, a differential resistance as low as 13 Ω and an output power of more than one order of magnitude higher than that of the same structure grown on sapphire are achieved. Due to higher thermal conductivity of GaN, output power of the LEDs saturates at higher injection currents compared to the devices grown on sapphire. [reprint (PDF)]
12.	Intrinsic AlGaN photodetectors for the entire compositional range D. Walker, X. Zhang, A. Saxler, P. Kung, J. Xu, and M. Razeghi SPIE Conference, San Jose, CA, -- February 12, 1997 ...[Visit Journal] Al_xGa_1-xN ultraviolet photoconductors with cut- off wavelengths from 365 nm to 200 nm have been fabricated and characterized. Various characteristics of the devices, such as photoresponse, voltage-dependent responsivity, frequency-dependent responsivity and noise spectral density, were measured and cross-referenced with optical, electrical and structural characteristics of the material to provide information about the mechanisms taking place during detection. The maximum detectivity reached 5.5 X 10⁸ cm·Hz^½/W at a modulating frequency of 14 Hz. The effective majority carrier lifetime in Al_xGa_1-xN materials, derived from frequency-dependent photoconductivity measurements, has been estimated to be from 6 to 35 msec. The frequency-dependent noise-spectrum shows that it is dominated by Johnson-noise at high frequencies for low Al-composition samples. [reprint (PDF)]
12.	Improved performance of quantum cascade lasers via manufacturable quality epitaxial side down mounting process utilizing aluminum nitride heatsinks A. Tsekoun, R. Go, M. Pushkarsky, M. Razeghi, C.K.N. Patel SPIE Conference, San Jose, CA, Vol. 6127, pp. 612702-- January 23, 2006 ...[Visit Journal] We report substantially improved performance of high power quantum cascade lasers by utilizing epi-side down mounting that provides superior heat dissipation properties. We have obtained CW power output of 450 mW at 20°C from mid-IR QCLs. The improved thermal management achieved with epi-side down mounting has also permitted us to carry out initial lifetime tests on the mid-IR QCLs. No degradation of power output is seen even after over 300 hours of CW operation at 25°C with power output in excess of 300 mW. We believe these improvements should permit incorporation of mid-IR QCLs in reliable instrumentation. [reprint (PDF)]
12.	Scale-up of the Chemical Lift-off of (In)GaN-based p-i-n Junctions from Sapphire Substrates Using Sacrificial ZnO Template Layers D. J. Rogers, S. Sundaram, Y. El Gmili, F. Hosseini Teherani, P. Bove, V. Sandana, P. L. Voss, A. Ougazzaden, A. Rajan, K.A. Prior, R. McClintock, & M. Razeghi Proc. SPIE 9364, Oxide-based Materials and Devices VI, 936424 -- March 24, 2015 ...[Visit Journal] (In)GaN p-i-n structures were grown by MOVPE on both GaN- and ZnO-coated c-sapphire substrates. XRD studies of the as-grown layers revealed that a strongly c-axis oriented wurtzite crystal structure was obtained on both templates and that there was a slight compressive strain in the ZnO underlayer which increased after GaN overgrowth. The InGaN peak position gave an estimate of 13.6at% for the indium content in the active layer. SEM and AFM revealed that the top surface morphologies were similar for both substrates, with an RMS roughness (5 μm x 5 μm) of about 10 nm. Granularity appeared slightly coarser (40nm for the device grown on ZnO vs 30nm for the device grown on the GaN template) however. CL revealed a weaker GaN near band edge UV emission peak and a stronger broad defect-related visible emission band for the structure grown on the GaN template. Only a strong ZnO NBE UV emission was observed for the sample grown on the ZnO template. Quarter-wafer chemical lift-off (CLO) of the InGaN-based p-i-n structures from the sapphire substrate was achieved by temporary-bonding the GaN surface to rigid glass support with wax and then selectively dissolving the ZnO in 0.1M HCl. XRD studies revealed that the epitaxial nature and strong preferential c-axis orientation of the layers had been maintained after lift-off. This demonstration of CLO scale-up, without compromising the crystallographic integrity of the (In)GaN p-i-n structure opens up the perspective of transferring GaN based devices off of sapphire substrates industrially. [reprint (PDF)]

Page 25 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)