Center for Quantum Devices - Most Downloaded Journal Articles

Page 22 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

13.	High performance focal plane array based on type-II InAs/GaSb superlattice heterostructures P.Y. Delaunay and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000M-1-10.-- February 1, 2008 ...[Visit Journal] Recent progress in growth techniques, structure design and processing has lifted the performances of Type-II InAs/GaSb superlattice photodetectors. A double heterostructure design, based on a low band gap (11 µm) active region and high band gap (5 µm) superlattice contacts, reduced the sensitivity of the superlattice to surface effects. The heterodiodes with an 11 µm cutoff, passivated with SiO₂, presented similar performances to unpassivated devices and a one order of magnitude increase of the resistivity of the sidewalls, even after flip-chip bonding and underfill. Thanks to this new design and to the inversion of the polarity of the devices, a high performance focal plane array with an 11 µm cutoff was demonstrated. The noise equivalent temperature difference was measured as 26 mK and 19 mK for operating temperatures of 81 K and 67 K. At an integration time of 0.08 ms, the FPA presented a quantum efficiency superior to 50%. [reprint (PDF)]
13.	Spatial Noise and Correctability of Type-II InAs/GaSb Focal Plane Arrays P.Y. Delaunay and M. Razeghi IEEE Journal of Quanutm Electronics, April 2010, Vol. 46, No. 4, p. 584-588-- April 1, 2010 ...[Visit Journal] A long wavelength infrared focal plane array based on Type-II InAs/GaSb superlattices was fabricated and characterized at 80 K. The noise equivalent temperature difference of the array was measured as low as 23 mK (f# = 2), for an integration time of 0.129 ms. The spatial noise of the array was dominated by the nonuniformity of the illumination through the circular aperture. A standard two-point nonuniformity correction improved the inhomogeneity equivalent temperature difference to 16 mK. The correctability just after calibration was 0.6. The long-term stability time was superior to 25 hours. [reprint (PDF)]
13.	Sharp/Tuneable UVC Selectivity and Extreme Solar Blindness in Nominally Undoped Ga2O3 MSM Photodetectors Grown by Pulsed Laser Deposition D. J. Rogers, A. Courtois, F. H. Teherani, V. E. Sandana, P. Bove, X. Arrateig, L. Damé, P. Maso, M. Meftah, W. El Huni, Y. Sama, H. Bouhnane, S. Gautier, A. Ougazzaden, M. Razeghi Proc. SPIE 11687, Oxide-based Materials and Devices XII, 116872D (24 March 2021); doi: 10.1117/12.2596194 ...[Visit Journal] Ga2O3 layers were grown on c-sapphire substrates by pulsed laser deposition. Optical transmission spectra were coherent with a bandgap engineering from 4.9 to 6.2 eV controlled via the growth conditions. X-ray diffraction revealed that the films were mainly β-Ga2O3 (monoclinic) with strong (-201) orientation. Metal-Semiconductor-Metal photodetectors based on gold/nickel Inter- Digitated-Transducer structures were fabricated by single-step negative photolithography. 240 nm peak response sensors gave over 2 orders-of-magnitude of separation between dark and light signal with state-of-the-art solar and visible rejection ratios ((I240 : I290) of > 3 x 105 and (I240 : I400) of > 2 x 106) and dark signals of <50 pA (at a bias of -5V). Spectral responsivities showed an exceptionally narrow linewidth (16.5 nm) and peak values exhibited a slightly superlinear increase with applied bias up to a value of 6.5 A/W (i.e. a quantum efficiency of > 3000%) at 20V bias. [reprint (PDF)]
13.	ZnO nanorod electrodes for hydrogen evolution and storage Harinipriya, S.; Usmani, B.; Rogers, D. J.; Sandana, V. E.; Teherani, F. Hosseini; Lusson, A.; Bove, P.; Drouhin, H.-J.; Razeghi, M. Proc. SPIE 8263, Oxide-based Materials and Devices III, 82631Y (February 9, 2012)-- February 9, 2012 ...[Visit Journal] Due to the attractive combination of a relatively high specific heat of combustion with a large specific energy capacity, molecular hydrogen (H2) is being investigated for use as an alternative to fossil fuels. Energy-efficient H₂ production and safe storage remain key technical obstacles to implementation of an H₂ based economy, however. ZnO has been investigated for use as an alternative photocatalytic electrode to TiO₂ for solarpowered photo-electro-chemical (PEC) electrolysis, in which H₂ is generated by direct water splitting in a cell with a metal cathode and a semiconducting anode. In this investigation, ZnO NR grown on Si (100) substrates by pulsed laser deposition were investigated for use as electrodes in the Hydrogen Evolution Reaction (HER). The electrochemical potential and Fermi energy of the ZnO NR were estimated from the electrochemical current density in acid and alkaline solutions via phenomenological thermodynamic analysis. As well as acting as an effective electrocalytic cathode, the ZnO NR appear to operate as a hydrogen reservoir. These results indicate that the ZnO NR have excellent potential for the storage of evolved H₂. [reprint (PDF)]
13.	Stability of far fields in double heterostructure and multiple quantum well InAsSb/InPAsSb/InAs midinfrared lasers H. Yi, A. Rybaltowski, J. Diaz, D. Wu, B. Lane, Y. Xiao, and M. Razeghi Applied Physics Letters 70 (24)-- June 16, 1997 ...[Visit Journal] Far fields in perpendicular direction to the junction are investigated in double heterostructure (DH) and multiple quantum well (MQW) midwave-infrared InAsSb/InPAsSb/InAs lasers (λ = 3.2–3.6 μm). Strong broadening of the far fields in the DH lasers was observed with increases in temperature and/or current. On the contrary, MQW lasers with otherwise identical structure exhibit very stable far fields as narrow as 23° for all the operating conditions investigated. Our experiment and theoretical modeling suggest that these different behaviors of far fields in DH and MQW lasers are attributed to the refractive index fluctuation in the InAsSb laser active region. [reprint (PDF)]
13.	Solar-blind photodetectors based on Ga₂O₃ and III-nitrides Ryan McClintock; Alexandre Jaud; Lakshay Gautam; Manijeh Razeghi Proc. SPIE 11288, Quantum Sensing and Nano Electronics and Photonics XVII, 1128803-- January 31, 2020 ...[Visit Journal] Recently, there has been a surge of interest in the wide bandgap semiconductors for solar blind photo detectors (SBPD). This work presents our recent progress in the growth/doping of AlGaN and Ga₂O₃ thin films for solar blind detection applications. Both of these thin films grown are grown by metal organic chemical vapor deposition (MOCVD) in the same Aixtron MOCVD system. Solar-blind metal-semiconductor-metal photodetectors were fabricated with Ga₂O₃. Spectral responsivity studies of the MSM photodetectors revealed a peak at 261 nm and a maximum EQE of 41.7% for a −2.5 V bias. We have also demonstrated AlGaN based solar-blind avalanche photodiodes with a gain in excess of 57,000 at ~100 volts of reverse bias. This gain can be attributed to avalanche multiplication of the photogenerated carriers within the device. Both of these devices show the potential of wide bandgap semiconductors for solar blind photo detectors. [reprint (PDF)]
13.	Sensitive detection of CO and N₂O using a high power CW 4.61 μm dfb-QCL based QEPAS sensor Yufei Ma; Rafał Lewicki; Manijeh Razeghi; Xin Yu; Frank K. Tittel CLEO: Science and Innovations, CLEO_SI 2013. 2013:JW2A.80-- June 9, 2013 ...[Visit Journal] A high power CW DFB-QCL based CO and N₂O QEPAS sensor demonstrating the MDL of 1.5 ppbv and 23 ppbv, respectively was developed. Continuous monitoring of atmospheric CO and N2O concentration levels were performed. [reprint (PDF)]
13.	Novel Sb-based Materials for Uncooled Infrared Photodetector Applications J.J. Lee and M. Razeghi Journal of Crystal Growth 221 (1-4)-- December 1, 2000 ...[Visit Journal] We have developed low-pressure metalorganic chemical vapor deposition technology for the growth of novel III-V Sb-based compounds such as InTlSb, InTlAsSb. and InSbSi. The incorporation of Tl and Si is investigated with various characterization techniques. Preliminary infrared photodetectors based on these materials are fabricated and tested. The maximum responsivity of an In0.96Tl0.04Sb photodetector is about 6.64 V/W at 77 K, corresponding to a Johnson-noise-limited detectivity of about 7.64 x 10(8) cm Hz(1/2)/W. Photoresponse of the In0.94Tl0.06Sb photodetector has been extended to 11 mum at 300K. Infrared photoresponse up to 15 mum is achieved from the InTlAsSb alloy at room temperature. We also demonstrate the uncooled InSbBi photodetector operating in the 8-12 mum range. The voltage responsivity at 10.6 mum is about 1.9mV/W at 300K and the corresponding Johnson-noise-limited detectivity is 1.2 x 10(6) cm Hz(1/2)/W. The carrier lifetime is estimated to be 0.7ns. [reprint (PDF)]
13.	Photoluminescence linewidth narrowing in Yb-doped GaN and InGaN thin films K. Dasari, J. Wang, W.M. Jadwisienczak, V. Dierolf, M. Razeghi, R. Palai Journal of Luminescence Volume 209, May 2019, Pages 237-243-- January 14, 2019 ...[Visit Journal] We report on photoluminescence (PL) properties of GaN, GaN:Yb, InGaN, and InGaN:Yb thin films grown on (0001) sapphire substrates by plasma assisted molecular beam epitaxy (MBE). X-ray diffraction pattern of the films confirms c-axis oriented growth. The concentration of Yb and In was obtained by X-ray photoelectron spectroscopy (XPS) and was found to be 5 (+/- 0.5) at.% and 30 (+/- 1.5) at.%, respectively. The GaN:Yb and InGaN:Yb thin films show a significant linewidth narrowing in PL spectra compared to GaN and InGaN thin films. This could be attributed to the reduction of the defect related non-radiative recombination paths and suppression of the structural defects and dislocations because of the in situ rare earth (Yb)-doping during the growth. The temperature dependent photoluminescence of GaN:Yb thin film follows the Varshni model, whereas InGaN:Yb film shows a complex S-shaped like behavior, which can be explained by the localization effect using the Band-Tail model. [reprint (PDF)]
13.	Recent advances in MOCVD growth of InxGa1-xAsyP1-y alloys M. Razeghi, J.P. Duchemin M. Razeghi, J.P. Duchemin, Recent advances in MOCVD growth of InxGa1-xAsyP1-y alloys, Journal of Crystal Growth, Volume 70, Issues 1–2, 1984, Pages 145-149,-- December 1, 1984 ...[Visit Journal] The low pressure metalorganic chemical vapour deposition (LPMOCVD) growth of GaxIn1-xAsyP1-y-InP lattice matched system, with high mobilities, sharp interfaces, low background doping densities, and the formation of a two-dimensional electron gas (2DEG) at the interfaces, has recently made spectacular advances, as in evidenced by the availability of high quality DH lasers, PIN photodiodes, and Gunn diodes. We present here some new results obtained on the above-mentioned material and devices. [reprint (PDF)]
13.	Overview of Quantum Cascade Laser Research at the Center for Quantum Devices S. Slivken, A. Evans, J. Nguyen, Y. Bai, P. Sung, S.R. Darvish, W. Zhang and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 69000B-1-8.-- February 1, 2008 ...[Visit Journal] Over the past several years, our group has endeavored to develop high power quantum cascade lasers for a variety of remote and high sensitivity infrared applications. The systematic optimization of laser performance has allowed for demonstration of high power, continuous-wave quantum cascade lasers operating above room temperature. In the past year alone, the efficiency and power of our short wavelength lasers (~4.8 µm) has doubled. In continuous wave at room temperature, we have now separately demonstrated ~10% wallplug efficiency and ~700 mW of output power. Up to now, we have been able to show that room temperature continuous wave operation with > 100 mW output power in the 3.8 < λ < 11.5 µm wavelength range is possible. [reprint (PDF)]
13.	III-Nitride Optoelectronic Devices: From Ultraviolet Toward Terahertz M. Razeghi IEEE Photonics Journal-Breakthroughs in Photonics 2010, Vol. 3, No. 2, p. 263-267-- April 26, 2011 ...[Visit Journal] We review III-Nitride optoelectronic device technologies with an emphasis on recent breakthroughs. We start with a brief summary of historical accomplishments and then report the state-of-the-art in three key spectral regimes: (1) Ultraviolet (AlGaN-based avalanche photodiodes, single photon detectors, focal plane arrays, and light emitting diodes), (2) Visible (InGaN-based solid state lighting, lasers, and solar cells), and (3) Near-, mid-infrared, and terahertz (AlGaN/GaN-based gap-engineered intersubband devices). We also describe future trends in III-Nitride optoelectronic devices. [reprint (PDF)]
13.	Reliability in room-temperature negative differential resistance characteristics of low-aluminum contact AlGaN/GaN double-barrier resonant tunneling diodes C. Bayram, Z. Vashaei, and M. Razeghi Applied Physics Letters, Vol. 97, No. 18, p. 181109-1-- November 1, 2010 ...[Visit Journal] AlGaN/GaN resonant tunneling diodes (RTDs), consisting of 20% (10%) aluminum-content in double-barrier (DB) active layer, were grown by metal-organic chemical vapor deposition on freestanding polar (c-plane) and nonpolar (m-plane) GaN substrates. RTDs were fabricated into 35-μm-diameter devices for electrical characterization. Lower aluminum content in the DB active layer and minimization of dislocations and polarization fields increased the reliability and reproducibility of room-temperature negative differential resistance (NDR). Polar RTDs showed decaying NDR behavior, whereas nonpolar ones did not significantly. Averaging over 50 measurements, nonpolar RTDs demonstrated a NDR of 67 Ω, a current-peak-to-valley ratio of 1.08, and an average oscillator output power of 0.52 mW. [reprint (PDF)]
13.	EPR STUDY OF Mn 2. AROUND THE FERROELASTIC TRANSITION POINT OF Pb3(PO4)2 M. Razeghi, B. Houlier and M. Yuste M. Razeghi et al. EPR STUDY OF Mn 2. AROUND THE FERROELASTIC TRANSITION POINT OF Pb3(PO4)2, Solid State Communications, Vol. 26, pp. 665-668. -- January 26, 1978 ...[Visit Journal] The spin Hamiltonian parameters of Mn 2÷ have been measured above and below the transition point (180"C) of the lead phosphate. They show that Mn 2+ substitutes a Pbl ion. Between 175 and 180vC the principal axis OX of the fine tensor is parallel to the wave vector of the soft mode which condensates at the transition point. An exaltation of the linewidth is observed. The linewidth remains constant within 50C of Te; in this temperature range, the "static regime" is achieved, and the correlation time of the fluctuations is less than 10 -s sec. [reprint (PDF)]
13.	InGaAs/InGaP Quantum-Dot Photodetector with a High Detectivity H. Lim, S. Tsao, M. Taguchi, W. Zhang, A. Quivy and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 61270N-- January 23, 2006 ...[Visit Journal] Quantum-dot infrared photodetectors (QDIPs) have recently been considered as strong candidates for numerous applications such as night vision, space communication, gas analysis and medical diagnosis involving middle and long wavelength infrared (MWIR and LWIR respectively) operation. This is due to their unique properties arising from their 3-dimensional confinement potential that provides a discrete density of states. They are expected to outperform quantum-well infrared photodetectors (QWIPs) as a consequence of their natural sensitivity to normal incident radiation, their higher responsivity and their higher-temperature operation. So far, most of the QDIPs reported in the literature were based on the InAs/GaAs system and were grown by molecular beam epitaxy (MBE). Here, we report on the growth of a high detectivity InGaAs/InGaP QDIP grown on a GaAs substrate using low-pressure metalorganic chemical vapor deposition (MOCVD). [reprint (PDF)]
13.	Characterization of high quality GaInP/GaAs superlattices grown on GaAs and Si substrates by gas source molecular beam epitaxy C. Jelen, S. Slivken, X.G. He, and M. Razeghi and S. Shastry Journal of Vacuum Science and Technology B 12 (2)-- March 1, 1994 ...[Visit Journal] We report an analysis of the heteroepitaxial interfaces in high quality GaInP–GaAs superlattices grown simultaneously on GaAs and Si substrates by gas source molecular beam epitaxy. These two superlattices have been studied using high resolution x-ray diffraction measurements. Sharp superlattice satellites, with very little broadening, are observed within a 6° range for the sample on GaAs. Photoluminescence peaks with full widths at half-maximums of 5 and 7 meV are obtained at 4 K for samples with 58 Å wells on GaAs and Si, respectively. Room temperature exciton absorption is observed in the photovoltage measurements for a superlattice grown on Si substrate. The thicknesses determined by x-ray analysis are consistent with those obtained by a Kronig–Penny model fitting of the photovoltage spectroscopy. [reprint (PDF)]
13.	Room temperature operation of 8-12 μm InSbBi infrared photodetectors on GaAs substrates J.J. Lee, J.D. Kim, and M. Razeghi Applied Physics Letters 73 (5)-- August 3, 1998 ...[Visit Journal] We report the room temperature operation of 8–12 μm InSbBi long-wavelength infrared photodetectors. The InSbBi/InSb heterostructures were grown on semi-insulating GaAs (001) substrates by low pressure metalorganic chemical vapor deposition. The voltage responsivity at 10.6 μm was about 1.9 mV/W at room temperature and the corresponding Johnson noise limited detectivity was estimated to be about 1.2×10⁶ cm·Hz^½/W. The carrier lifetime derived from the voltage dependent responsivity measurements was about 0.7 ns. [reprint (PDF)]
13.	On the interface properties of ZnO/Si electroluminescent diodes J.L. Pau, J. Piqueras, D.J. Rogers, F. Hosseini Teherani, K. Minder, R. McClintock, and M. Razeghi Journal of Applied Physics, Vol. 107, No. 3, p. 033719-1-- February 1, 2010 ...[Visit Journal] ZnO layers grown on n⁻–Si(100), n⁺–Si(100), and n^––Si(111) substrates by pulsed-laser deposition were found to give electroluminescence. Light emission was observed in the form of discrete spots for currents over 1 mA with a white appearance to the naked eye. The intensity of these spots showed an erratic behavior over time, appearing and disappearing at random, while showing an associated random telegraph noise in the current signal. Regardless the substrate used, the electroluminescence spectra had a main broadband emission centered at about 600 nm and a relatively small peak at around 380 nm which corresponds to the energy of ZnO near band edge emission. Furthermore, the devices exhibited rectifying characteristics, whose current blocking direction depended on the substrate orientation. Optimization of ZnO conductivity and performing sample growth in N₂ ambient were found to be critical to enhance the emission intensity. Rutherford backscattering characterization revealed the existence of an intermixed region at the interface between ZnO and Si. To study the electronic properties at the interface, frequency dependent capacitance measurements were carried out. The junction capacitance became frequency dependent at the bias voltages at which light emission occurs due to the relatively slow trapping and generation processes at deep centers. These centers are believed to play an important role in the mechanism of light emission. [reprint (PDF)]
13.	GaN nanostructured p-i-n photodiodes J.L. Pau, C. Bayram, P. Giedraitis, R. McClintock, and M. Razeghi Applied Physics Letters, Vol. 93, No. 22, p. 221104-1-- December 1, 2008 ...[Visit Journal] We report the fabrication of nanostructured p-i-n photodiodes based on GaN. Each device comprises arrays of ~200 nm diameter and 520 nm tall nanopillars on a 1 µm period, fabricated by e-beam lithography. Strong rectifying behavior was obtained with an average reverse current per nanopillar of 5 fA at −5 V. In contrast to conventional GaN diodes, nanostructured devices reproducibly show ideality factors lower than 2. Enhanced tunneling through sidewall surface states is proposed as the responsible mechanism for this behavior. Under backillumination, the quantum efficiency in nanostructured devices is partly limited by the collection efficiency of holes into the nanopillars. [reprint (PDF)]
13.	Top-emission ultraviolet light-emitting diodes with peak emission at 280 nm A. Yasan, R. McClintock, K. Mayes, S.R. Darvish, P. Kung, and M. Razeghi Virtual Journal of Nanoscale Science & Technology, 5-- August 5, 2002 ...[Visit Journal][reprint (PDF)]
13.	Noise analysis in type-II InAs/GaSb focal plane arrays P.Y. Delaunay and M. Razeghi Journal of Applied Physics, Vol. 106, Issue 6, p. 063110-- September 15, 2009 ...[Visit Journal] A long wavelength infrared focal plane array based on type-II InAs/GaSb superlattices was fabricated and characterized at 80 K. The noise equivalent temperature difference in the array was measured as low as 23 mK for an integration time of 0.129 ms. The noise behavior of the detectors was properly described by a model based on thermal, shot, read out integrated circuit, and photon noises. The noise of the imager was dominated by photon noise for photon fluxes higher than 1.8×10¹⁵ ph·s⁻¹·cm⁻². At lower irradiance, the imager was limited by the shot noise generated by the dark current or the noise of the testing system. The superlattice detector did not create 1/f noise for frequencies above 4 mHz. As a result, the focal plane array did not require frequent calibrations. [reprint (PDF)]
13.	Short-wavelength ultraviolet light-emitting diodes based on AlGaN M. Razeghi; A. Yasan; R. McClintock; K. Mayes; P. Kung 2005 Conference on Lasers and Electro-Optics, CLEO. 153-155 [CMI5] (2005)-- May 22, 2005 ...[Visit Journal] We review our progress toward realization of highly-efficient ultraviolet light-emitting diodes (UV LEDs) based on high Al-composition Al_xGa_1-xN. Milliwatt level optical output powers have been measured at wavelengths as short as 247 nm. [reprint (PDF)]
13.	Room temperature CW operation of GaInAsP/InP double heterostructure diode lasers emitting at 1.5 μm grown by low pressure metalorganic chemical vapour deposition (LP-MO CVD) M. Razeghi, P. Hirtz, R. Blondeau, J.-P. Larivain, L. Noel, B. de Cremoux, J.-P. Duchemin Electronics Letters Volume 18, Issue 3 https://doi.org/10.1049/el:19820088-- February 1, 1982 ...[Visit Journal] Room temperature continuous wave (CW) operation at 1.5 μm has been achieved in GaInAsP/InP DH lasers fabricated on material grown by low-pressure metalorganic chemical vapour deposition (LP-MO CVD). Threshold currents as low as 200 mA DC have been measured for devices with a stripe width of 9 μm and a cavity length of 300 μm. Values of To as high as 64 K have been obtained, where To is defined by the expression Jth(T) = Jth(0) exp (T/To). Fundamental transverse mode oscillation has been achieved up to an output power of 10 mW. [reprint (PDF)]
13.	High performance monolithic, broadly tunable mid-infrared quantum cascade lasers WENJIA Zhou, DONGHAI Wu, RYAN McCLINTOCK, STEVEN SLIVKEN, AND MANIJEH RAZEGH1 Optica 4(10), p. 1228-- October 10, 2017 ...[Visit Journal] Mid-infrared lasers, emitting in the spectral region of 3-12 µm that contains strong characteristic vibrational transitions of many important molecules, are highly desirable for spectroscopy sensing applications. High-efficiency quantum cascade lasers have been demonstrated with up to watt-level output power in the mid-infrared region. However, the wide wavelength tuning that is critical for spectroscopy applications still largely relies on incorporating external gratings, which have stability issues. Here, we demonstrate a monolithic, broadly tunable quantum cascade laser source emitting between 6.1 and 9.2 µm through an on-chip integration of a sampled grating distributed feedback tunable laser array and a beam combiner. High peak power up to 65 mW has been obtained through a balanced high-gain active region design, efficient waveguide layout, and the development of a broadband antireflection coating. Nearly fundamental transversemode operation is achieved for all emission wavelengths with a pointing stability better than 1.6 mrad (0.1 °). The demonstrated laser source opens new opportunities for mid-infrared spectroscopy. [reprint (PDF)]
13.	Highly temperature insensitive quantum cascade lasers Y. Bai, N. Bandyopadhyay, S. Tsao, E. Selcuk, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 97, No. 25-- December 20, 2010 ...[Visit Journal] An InP based quantum cascade laser (QCL) heterostructure emitting around 5 μm is grown with gas-source molecular beam epitaxy. The QCL core design takes a shallow-well approach to maximize the characteristic temperatures, T(0) and T(1), for operations above room temperature. A T(0) value of 383 K and a T(1) value of 645 K are obtained within a temperature range of 298–373 K. In room temperature continuous wave operation, this design gives a single facet output power of 3 W and a wall plug efficiency of 16% from a device with a cavity length of 5 mm and a ridge width of 8 μm. [reprint (PDF)]

Page 22 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)