Center for Quantum Devices - Most Downloaded Journal Articles

Page 20 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

13.	cw operation of 1.57‐μm GaxIn1−xAsyP1−yInP distributed feedback lasers grown by low‐pressure metalorganic chemical vapor deposition M. Razeghi; R. Blondeau; K. Kazmierski; M. Krakowski; B. de Cremoux; J. P. Duchemin; J. C. Bouley Appl. Phys. Lett. 45, 784–786 (1984)-- October 1, 1984 ...[Visit Journal] Continuous wave operation of 1. 57-Jim distributed feedback lasers fabricated on material grown by two-step low-pressure metalorganic chemical vapor deposition growth process is reported for the first time. Room-temperature continuous wave threshold currents as low as 60 rnA have been measured for devices with cavity length of 300 Jim and stripe width of 5 Jim. Single longitudinal mode operation at fixed mode was obtained under the continuous wave condition, in the temperature range 9-90 °C, with the wavelength shift of 0.9 A/C. A stop band of25 A in which no resonance mode emission existed, was observed in the output spectrum of the distributed feedback laser. [reprint (PDF)]
13.	Solar-blind photodetectors and focal plane arrays based on AlGaN R. McClintock, M. Razeghi Proc. SPIE 9555, Optical Sensing, Imaging, and Photon Counting: Nanostructured Devices and Applications, 955502-- August 25, 2015 ...[Visit Journal] III-Nitride material system (AlGaInN) possesses unique optical, electrical and structural properties such as a wide tunable direct bandgap, inherent fast carrier dynamics; good carrier transport properties, high breakdown fields; and high robustness and chemical stability. Recent technological advances in the wide bandgap AlGaN portion of this material system have led to a renewed interest in ultraviolet (UV) photodetectors. These detectors find use in numerous applications in the defense, commercial and scientific arenas such as covert space-to-space communications, early missile threat detection, chemical and biological threat detection and spectroscopy, flame detection and monitoring, UV environmental monitoring, and UV astronomy.1,2,3 Back illuminated detectors operating in the solar blind region are of special interest. Back illumination allows the detector to be hybridized to a silicon read-out integrated circuit, epi-side down, and still collect light through the back of the transparent sapphire substrate. This allows the realization of solar blind focal plane arrays (FPAs) for imaging applications. Solar-blind FPAs are especially important because of the near total absence of any background radiation in this region. In this talk, we will present our recent back-illuminated solar-blind photodetector, mini-array, and FPA results. By systematically optimizing the design of the structure we have realized external quantum efficiencies (EQE) of in excess of 89% for pixel-sized detectors. Based on the absence of any anti-reflection coating, this corresponds to nearly 100% internal quantum efficiency. At the same time, the dark current remains below ~2 × 10^-9 A/cm² even at 10 volts of reverse bias. The detector has a very sharp falloff starting at 275 with the UV-solar rejection of better than three orders of magnitude, and a visible rejection ratio is more than 6 orders of magnitude. This high performance photodetector design was then used as the basis of the realization of solar-blind FPA. We demonstrated a 320×256 FPA with a peak detection wavelength of 278nm. The operability of the FPA was better than 92%, and excellent corrected imaging was obtained. [reprint (PDF)]
13.	Investigation of surface leakage reduction for small pitch shortwave infrared photodetectors Arash Dehzangi, Quentin Durlin, Donghai Wu, Ryan McClintock, Manijeh Razeghi Semiconductor Science and Technology, 34(6), 06LT01-- May 25, 2019 ...[Visit Journal] Different passivation techniques are investigated for reducing leakage current in small pixel (down to 9 μm) heterostructure photodetectors designed for the short-wavelength infrared range. Process evaluation test chips were fabricated using the same process as for focal plane arrays. Arrays of small photodetectors were electrically characterized under dark conditions from 150 K to room temperature. In order to evaluate the leakage current, we studied the relation between the inverse of dynamic resistance at −20 mV and zero bias and perimeter over area P/A ratio as the pixel size is scaled down. At 150 K, leakage current arising from the perimeter dominates while bulk leakage dominates at room temperature. We find that in shortwave devices directly underfilling hybridized devices with a thermoset epoxy resin without first doing any additional passivation/protection after etching gives the lowest leakage with a surface resistance of 4.2 × 10⁹ and 8.9 × 10³ Ω· cm⁻¹ at 150 and 300 K, for −20 mV of bias voltage, respectively. [reprint (PDF)]
13.	Second harmonic generation in hexagonal silicon carbide P.M. Lundquist, W.P. Lin, G.K. Wong, M. Razeghi, and J.B. Ketterson Applied Physics Letters 66 (15)-- April 10, 1995 ...[Visit Journal] We report optical second harmonic generation measurements in single crystal α-SiC of polytype 6H. The angular dependence of second harmonic intensity was consistent with two independent nonvanishing second order susceptibility components, as expected for a crystal with hexagonal symmetry. For the fundamental wavelength of 1.064 μm the magnitudes of the two components were determined to be χ_zzz⁽²⁾=±1.2×10⁻⁷ and χ_zxx⁽²⁾=∓1.2×10⁻⁸ esu. The corresponding linear electro‐optic coefficient computed from this value is r^zzz=±100 pm/V. The wavelength dependence of the nonlinear susceptibility was examined for second harmonic wavelengths between the bandgap (400 nm) and the red (700 nm), and was found to be relatively uniform over this region. The refractory nature of this compound and its large nonlinear optical coefficients make it an attractive candidate for high power nonlinear optical waveguide applications. [reprint (PDF)]
13.	Type-II InAs/GaSb photodiodes and focal plane arrays aimed at high operating temperatures M. Razeghi, S. Abdollahi Pour, E.K. Huang, G. Chen, A. Haddadi, and B.M. Nguyen Opto-Electronics Review (OER), Vol. 19, No. 3, June 2011, p. 46-54-- June 1, 2011 ...[Visit Journal] Recent efforts to improve the performance of type-II InAs/GaSb superlattice photodiodes and focal plane arrays (FPA) have been reviewed. The theoretical bandstructure models have been discussed first. A review of recent developments in growth and characterization techniques is given. The efforts to improve the performance of MWIR photodiodes and focal plane arrays (FPAs) have been reviewed and the latest results have been reported. It is shown that these improvements has resulted in background limited performance (BLIP) of single element photodiodes up to 180 K. FPA shows a constant noise equivalent temperature difference (NEDT) of 11 mK up to 120 K and it shows human body imaging up to 170 K. [reprint (PDF)]
13.	Mid-wavelength infrared heterojunction phototransistors based on type-II InAs/AlSb/GaSb superlattices A. Haddadi, S. Adhikary, A. Dehzangi, and M. Razeghi Applied Physics Letters 109, 021107-- July 12, 2016 ...[Visit Journal] A mid-wavelength infrared heterojunction phototransistor based on type-II InAs/AlSb/GaSb superlattices on GaSb substrate has been demonstrated. Near a wavelength of 4 μm saturated optical gains of 668 and 639 at 77 and 150 K, respectively, are demonstrated over a wide dynamic range. At 150 K, the unity optical gain collector dark current density and DC current gain are 1 × 10⁻³ A/cm² and 3710, respectively. This demonstrates the potential for use in high-speed applications. In addition, the phototransistor exhibits a specific detectivity value that is four times higher compared with a state-of-the-art type-II superlattice-based photodiode with a similar cut-off wavelength at 150 K. [reprint (PDF)]
13.	Recent advances in high performance antimonide-based superlattice FPAs E.K. Huang, B.M. Nguyen, S.R. Darvish, S. Abdollahi Pour, G. Chen, A. Haddadi, and M.A. Hoang SPIE Proceedings, Infrared technology and Applications XXXVII, Orlando, FL, Vol. 8012, p. 80120T-1-- April 25, 2011 ...[Visit Journal] Infrared detection technologies entering the third generation demand performances for higher detectivity, higher operating temperature, higher resolution and multi-color detection, all accomplished with better yield and lower manufacturing/operating costs. Type-II antimonide based superlattices (T2SL) are making firm steps toward the new era of focal plane array imaging as witnessed in the unique advantages and significant progress achieved in recent years. In this talk, we will present the four research themes towards third generation imagers based on T2SL at the Center for Quantum Devices. High performance LWIR megapixel focal plane arrays (FPAs) are demonstrated at 80K with an NEDT of 23.6 mK using f/2 optics, an integration time of 0.13 ms and a 300 K background. MWIR and LWIR FPAs on non-native GaAs substrates are demonstrated as a proof of concept for the cost reduction and mass production of this technology. In the MWIR regime, progress has been made to elevate the operating temperature of the device, in order to avoid the burden of liquid nitrogen cooling. We have demonstrated a quantum efficiency above 50%, and a specific detectivity of 1.05x10¹² cm·Hz^1/2/W at 150 K for 4.2 μm cut-off single element devices. Progress on LWIR/LWIR dual color FPAs as well as novel approaches for FPA fabrication will also be discussed. [reprint (PDF)]
13.	Evaluating the size-dependent quantum efficiency loss in a SiO₂-Y₂O₃hybrid gated type-II InAs/GaSb long-infrared photodetector array G. Chen , A. M. Hoang , and M. Razeghi Applied Physics Letters 104 , 103509 (2014)-- March 14, 2014 ...[Visit Journal] Growing Y₂O₃ on 20 nm SiO₂ to passivate a 11 μm 50% cut-off wavelength long-wavelength infrared type-II superlattice gated photodetector array reduces its saturated gate bias (VG_sat ) to −7 V. Size-dependent quantum efficiency (QE) losses are evaluated from 400 μm to 57 μm size gated photodiode. Evolution of QE of the 57 μm gated photodiode with gate bias and diode operation bias reveals different surface recombination mechanisms. At 77 K and VG,sat , the 57 μm gated photodiode exhibits QE enhancement from 53% to 63%, and it has 1.2 × 10⁻⁵ A/cm² dark current density at −200 mV, and a specific detectivity of 2.3 × 10¹² Jones. [reprint (PDF)]
13.	Investigation of MgZnO/ZnO heterostructures grown on c-sapphire substrates by pulsed laser deposition D. J. Rogers ; F. Hosseini Teherani ; P. Bove ; A. Lusson ; M. Razeghi Proc. SPIE 8626, Oxide-based Materials and Devices IV, 86261X (March 18, 2013)-- March 18, 2013 ...[Visit Journal] MgZnO thin films were grown on c-sapphire and ZnO-coated c-sapphire substrates by pulsed laser deposition from a ZnMgO target with 4 at% Mg. The MgZnO grown on the ZnO underlayer showed significantly better crystal quality than that grown directly on sapphire. AFM studies revealed a significant deterioration in surface morphology for the MgZnO layers compared with the ZnO underlayer. Optical transmission studies indicated a MgZnO bandgap of 3.61eV (compared with 3.34eV for the ZnO), which corresponds to a Mg content of about 16.1 at%. The MgZnO/ZnO heterojunction showed an anomalously low resistivity, which was more than two orders of magnitude less than the MgZnO layer and an order of magnitude lower than that for the ZnO layer. It was suggested that this may be attributable to the presence of a 2D electron gas at the ZnMgO/ZnO heterointerface. [reprint (PDF)]
13.	Engineering Multi-Section Quantum Cascade Lasers for Broadband Tuning Steven Slivken and Manijeh Razeghi Photonics 3, 41-- June 27, 2016 ...[Visit Journal] In an effort to overcome current limitations to electrical tuning of quantum cascade lasers, a strategy is proposed which combines heterogeneous quantum cascade laser gain engineering with sampled grating architectures. This approach seeks to not only widen the accessible spectral range for an individual emitter, but also compensate for functional non-uniformity of reflectivity and gain lineshapes. A trial laser with a dual wavelength core is presented which exhibits electroluminescence over a 750 cm⁻¹ range and discrete single mode laser emission over a 700 cm⁻¹ range. Electrical tuning over 180 cm⁻¹ is demonstrated with a simple sampled grating design. A path forward to even wider tuning is also described using more sophisticated gain and grating design principles. [reprint (PDF)]
13.	High-power continuous-wave operation of distributed-feedback quantum-cascade lasers at λ ~ 7.8 µm S.R. Darvish, W. Zhang, A. Evans, J.S. Yu, S. Slivken, and M. Razeghi Applied Physics Letters, 89 (25)-- December 18, 2006 ...[Visit Journal] The authors present high-power continuous-wave (cw) operation of distributed-feedback quantum-cascade lasers. Continuous-wave output powers of 56 mW at 25 °C and 15 mW at 40 °C are obtained. Single-mode emission near 7.8 μm with a side-mode suppression ratio of >=30 dB and a tuning range of 2.83 cm⁻¹ was obtained between 15 and 40 °C. The device exhibits no beam steering with a full width at half maximum of 27.4° at 25 °C in cw mode. [reprint (PDF)]
13.	High Power 3-12 μm Infrared Lasers: Recent Improvements and Future Trends M. Razeghi, S. Slivken, A. Tahraoui, A. Matlis, and Y.S. Park Advanced Research Workshop on Semiconductor Nanostructures, Queenstown, New Zealand; Proceedings -- February 5, 2003 ...[Visit Journal] In this paper, we discuss the progress of quantum cascade lasers (QCLs) grown by gas-source molecular beam epitaxy. Room temperature QCL operation has been reported for lasers emitting between 5-11 μm, with 9-11 μm lasers operating up to 425 K. Laser technology for the 3-5 μm range takes advantage of a strain-balanced active layer design. We also demonstrate record room temperature peak output powers at 9 and 11 μm (2.5 and 1 W, respectively) as well as record low 80K threshold current densities (250 A/cm²) for some laser designs. Preliminary distributed feedback (DFB) results are also presented and exhibit single mode operation for 9 μm lasers at room temperature. [reprint (PDF)]
13.	Monolithic integration of a short‐length GaInAs photoconductor with a GaAs/GaAlAs optical waveguide on a GaAs semi‐insulating substrate F. Mallecot; J. F. Vinchant; M. Razeghi; D. Vandermoere; J. P. Vilcot; D. Decoster Appl. Phys. Lett. 53, 2522–2524 (1988)-- December 19, 1988 ...[Visit Journal] We report the first fabrication of a GaO. 47 Inn. 53 As planar photoconductive detector, associated with a GaAs/GaAIAs rib waveguide grown on a semi-insulating GaAs substrate, which needs a short-length absorbing layer to detect the optical signal. Because of the GaAIAs epilayer, a GalnAs length of about 100 tl1n only is needed to detect 90% of the opticai signal, accordingly to results predicted using a four-layer model with complex refractive indices in each layer. [reprint (PDF)]
13.	Advanced InAs/GaSb Superlattice Photovoltaic Detectors for Very-Long Wavelength Infrared Applications Y. Wei, A. Gin, M. Razeghi, and G.J. Brown Applied Physics Letters 80 (18)-- May 6, 2002 ...[Visit Journal] We report on the temperature dependence of the photoresponse of very long wavelength infrared type-II InAs/GaSb superlattice based photovoltaic detectors grown by molecular-beam epitaxy. The detectors had a 50% cutoff wavelength of 18.8 μm and a peak current responsivity of 4 A·W^-1 at 80 K. A peak detectivity of 4.5×10¹⁰ cm· Hz^½·W^-1 was achieved at 80 K at a reverse bias of 110 mV. The generation–recombination lifetime was 0.4 ns at 80 K. The cutoff wavelength increased very slowly with increasing temperature with a net shift from 20 to 80 K of only 1.2 μm [reprint (PDF)]
13.	Harmonic injection locking of high-power mid-infrared quantum cascade lasers Feihu Wang, Steven Slivken, and Manijeh Razeghi OSA Photonics Research •https://doi.org/10.1364/PRJ.423573 ...[Visit Journal] High-power, high-speed quantum cascade lasers (QCLs) with stable emission in the mid-infrared regime are of great importance for applications in metrology, telecommunication, and fundamental tests of physics. Owing to the inter-sub-band transition, the unique ultrafast gain recovery time of the QCL with picosecond dynamics is expected to overcome the modulation limit of classical semiconductor lasers and bring a revolution for the next generation of ultrahigh-speed optical communication. Therefore, harmonic injection locking, offering the possibility to fast modulate and greatly stabilize the laser emission beyond the rate limited by cavity length, is inherently adapted to QCLs. In this work, we demonstrate for the first time the harmonic injection locking of a mid-infrared QCL with an output power over 1 watt in continuous-wave operation at 288 K. Compared with an unlocked laser, the inter-mode spacing fluctuation of an injection locked QCL can be considerably reduced by a factor above 1×10 E3, which permits the realization of an ultra-stable mid-infrared semiconductor laser with high phase coherence and frequency purity. Despite temperature change, this fluctuation can be still stabilized to hertz level by a microwave modulation up to ∼18 GHz. These results open up the prospect of the applications of mid-infrared QCL technology for frequency comb engineering, metrology and the next generation ultrahigh-speed telecommunication. It may also stimulate new schemes for exploring ultrafast mid-infrared pulse generation in QCLs. [reprint (PDF)]
13.	Bias-selectable three-color short-, extended-short-, and mid-wavelength infrared photodetectors based on type-II InAs/GaSb/AlSb superlattices Abbas Haddadi, and Manijeh Razeghi Optics Letters Vol. 42, Iss. 21, pp. 4275-4278-- October 16, 2017 ...[Visit Journal] A bias-selectable, high operating temperature, three-color short-, extended-short-, and mid-wavelength infrared photodetector based on InAs/GaSb/AlSb type-II superlattices on GaSb substrate has been demonstrated. The short-, extended-short-, and mid-wavelength channels’ 50% cutoff wavelengths were 2.3, 2.9, and 4.4μm, respectively, at 150K. The mid-wavelength channel exhibited a saturated quantum efficiency of 34% at 4μm under +200 mV bias voltage in a front-side illumination configuration and without any antireflection coating. At 200mV, the device exhibited a dark current density of 8.7×10⁻⁵ A/cm² providing a specific detectivity of ∼2×10¹¹ cm·Hz^1/2/W at 150K. The short-wavelength channel achieved a saturated quantum efficiency of 20% at 1.8μm. At −10 mV, the device’s dark current density was 5.5×10⁻⁸ A/cm². At zero bias, its specific detectivity was 1×10¹¹ cm·Hz^1/2/W at 150K. The extended short-wavelength channel achieved a saturated quantum efficiency of 22% at 2.75 μm. Under −2 V bias voltage, the device exhibited a dark current density of 1.8×10⁻⁶ A/cm² providing a specific detectivity of 6.3×10¹¹ cm·Hz^1/2/W at 150K. [reprint (PDF)]
13.	Recent progress of widely tunable, CW THz sources based QCLs at room temperature Manijeh Razeghi Terahertz Science and Technology, Vol.10, No.4, pp. 87-151-- December 7, 2017 ...[Visit Journal] The THz spectral region is of significant interest to the scientific community, but is one of the hardest regions to access with conventional technology. A wide range of compelling new applications are initiating a new revolution in THz technology, especially with regard to the development of compact and versatile devices for THz emission and detection. In this article, recent advances with regard to III-V semiconductor optoelectronics are explored with emphasis on how these advances will lead to the next generation of THz component technology [reprint (PDF)]
13.	8-13 μm InAsSb heterojunction photodiode operating at near room temperature J.D. Kim, S. Kim, D. Wu, J. Wojkowski, J. Xu, J. Piotrowski, E. Bigan, and M. Razeghi Applied Physics Letters 67 (18)-- October 30, 1995 ...[Visit Journal] p⁺-InSb/π-InAs_1−xSb_x/n⁺-InSb heterojunction photodiodes operating at near room temperature in the 8–13 μm region of infrared (IR) spectrum are reported. A room‐temperature photovoltaic response of up to 13 μm has been observed at 300 K with an x≊0.85 sample. The voltage responsivity‐area product of 3×10⁻⁵ V· cm²/W has been obtained at 300 K for the λ=10.6 μm optimized device. This was close to the theoretical limit set by the Auger mechanism, with a detectivity at room temperature of ≊1.5×10⁸ cm ·Hz^½/W. [reprint (PDF)]
13.	Room temperature continuous wave operation of λ ~ 3-3.2 μm quantum cascade lasers N. Bandyopadhyay, Y. Bai, S. Tsao, S. Nida, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 101, No. 24, p. 241110-1-- December 10, 2012 ...[Visit Journal] We demonstrate quantum cascade lasers emitting at wavelengths of 3–3.2 μm in the InP-based material system. The laser core consists of GaInAs/AlInAs using strain balancing technique. In room temperature pulsed mode operation, threshold current densities of 1.66 kA∕cm² and 1.97 kA∕cm², and characteristic temperatures (T₀) of 108 K and 102 K, are obtained for the devices emitting at 3.2 μm and 3 μm, respectively. Room temperature continuous wave operation is achieved at both wavelengths. [reprint (PDF)]
13.	High‐quality GaAs/Ga0.49In0.51P superlattices grown on GaAs and silicon substrates by low‐pressure metalorganic chemical vapor deposition Available M. Razeghi; Ph. Maurel; F. Omnes; M. Defour; C. Boothroyd; W. M. Stobbs; M. Kelly J. Appl. Phys. 63, 4511–4514 (1988) -- May 1, 1988 ...[Visit Journal] We report the successful growth of Ga0.49 Iuo.5 ! P-GaAs superlattices on GaAs and Si substrates by low-pressure metalorganic chemical vapor deposition. The high quality of the structure grown on GaAs and silicon substrates has been evidenced by transmission electron microscopy photographs, that show very sharp interfaces between GaAs wells and Gao.49InO.51 P barriers, with perfect control of thicknesses and compositions. Classical Hall measurements performed on the sample further demonstrated the presence of a twodimensional electron ga.<; with a mobility at T = 4 K , fL (4 K) = 50000 cm2 1V Is, and a carrier concentration n _ (4 K) = 2,9 X 1011 em -2. GaAs/Gao.49 InO. 51 P superlattices have been used, as well as buffer layer in order to grow GaAs on silicon substrates. Mirrorlike single-crystal GaAs has thus been obtained. A GaInP IGaAs heterostructure with electron HaH mobility as high as 6000 cm2 /V Is at 300 K and 80000 cm2 /V Is at 4 K has been grown, which is the highest mobility that has yet been reported for these materials, [reprint (PDF)]
13.	Very high performance LWIR and VLWIR type-II InAs/GaSb superlattice photodiodes with M-structure barrier B.M. Nguyen, D. Hoffman, P.Y. Delaunay, E.K. Huang and M. Razeghi SPIE Proceedings, Vol. 7082, San Diego, CA 2008, p. 708205-- September 3, 2008 ...[Visit Journal] LWIR and VLWIR type-II InAs/GaSb superlattice photodetectors have for long time suffered from a high dark current level and a low dynamic resistance which hampers the its emergence to the infrared detection and imaging industry. However, with the use of M-structure superlattice, a new Type-II binary InAs/GaSb/AlSb superlattice design, as an effective blocking barrier, the dark current in type-II superlattice diode has been significantly reduced. We have obtained comparable differential resistance product to the MCT technology at the cut-off wavelength of 10 and 14μm. Also, this new design is compatible with the optical optimization scheme, leading to high quantum efficiency, high special detectivity devices for photon detectors and focal plane arrays. [reprint (PDF)]
13.	Optical Investigations of GaAs-GaInP Quantum Wells and Superlattices Grown by Metalorganic Chemical Vapor Deposition Omnes F., and Razeghi M. Applied Physics Letters 59 (9), p. 1034-- May 28, 1991 ...[Visit Journal] Recent experimental results on the photoluminescence and photoluminescence excitation of GaAs‐Ga_0.51In_0.49P lattice‐matched quantum wells and superlattices are discussed. The full width at half maximum of a 10‐period GaAs‐GaInP superlattice with Lz=90 Å and LB=100 Å is 4 meV at 4 K. The photoluminescence excitation exhibits very sharp peaks attributed to the electron to light‐hole and electron to heavy‐hole transitions. The GaInP‐GaAs interface suffers from memory effect of In, rather than P or As elements. [reprint (PDF)]
13.	GaInAs and GaInAsP materials grown by low pressure MOCVD for microwave and optoelectronic applications J.P. Duchemin, J.P. Hirtz, M. Razeghi, M. Bonnet , S.D. Hersee J.P. Duchemin, J.P. Hirtz, M. Razeghi, M. Bonnet, S.D. Hersee, GaInAs and GaInAsP materials grown by low pressure MOCVD for microwave and optoelectronic applications, Journal of Crystal Growth, Volume 55, Issue 1, 1981, Pages 64-73-- October 1, 1981 ...[Visit Journal] The low pressure MOCVD technique has been successfully used to grow GaInAsP, lattice-matched to InP, for the complete compositional range between InP (λ=0.91 μm) and the ternary compound Ga0.47In0.53As (λ=1.67 μm). By contrast to LPE growth it has been found that during the MOCVD growth of double heterostructures InP can be grown directly onto the ternary or quaternary with no disturbance of the active layer, i.e. there is no effect equivalent to “melt back”. The compositional grading on both sides of the active layer was measured by scanning Auger spectroscopy on bevelled samples. It was found that the graded regions were typically less than 100 Å wide for GaInAsP active layers and less than 50 Å wide for GaInAs active layers. Single layers of undoped GaInAs exhibited a typical mobility of 6700 cm2 V-1s-1 at 1.5×1017 cm-3. The compositional uniformity of the ternary layers was characterised by measurement of the photoluminescence wavelength at various points on a large sample. The wavelength varied by <3 nm over 95% of the area, which was approximately 8 cm2. Our early MOCVD grown GaInAsP/InP DH lasers exhibited high thresholds due to a poor interface between the p-InP and the active layer. However, recently fabricated broad area lasers emitting at 1.27 μm show an average threshold current density of 1.5 kA cm-2 with a T0 of between 70 to 80 K. Stripe geometry lasers have being fabricated from this material and CW operation has been obtained. [reprint (PDF)]
13.	Band-gap narrowing and potential fluctuation in Si-doped GaN I.H. Lee, J.J. Lee, P. Kung, F.J. Sanchez, and M. Razeghi Applied Physics Letters 74 (1)-- January 4, 1999 ...[Visit Journal] We investigate the optical properties of two sets of Si-doped GaN epitaxial layers with different degree of compensation. The electron concentration dependence of the band-gap energy measured by photoluminescence is interpreted as band-gap narrowing effect and evaluated by a simple relation. The photoluminescence peak positions of heavily compensated samples are shifted downward with respect to those of moderately compensated samples, and the down shift becomes larger at higher electron density. Based on analysis of photoluminescence spectra, these prominent behaviors are accounted for by band-edge potential fluctuation associated with inhomogeneous residual impurities. [reprint (PDF)]
13.	Infrared detection from GaInAs/InP nanopillar arrays A. Gin, B. Movaghar, M. Razeghi and G.J. Brown Nanotechnology 16-- July 1, 2005 ...[Visit Journal] We report on the photoresponse from large arrays of 40 nm radius nanopillars with sensitivity in the long-wavelength infrared regime. Using photoluminescence techniques, a peak wavelength blue shift of approximately 5 meV was observed at 30 K from GaInAs/InP nanopillar structures, indicating carrier confinement effects. Responsivity measurements at 30 K indicated peak wavelength response at about 8 µm with responsivity of 420 mA/W at −2 V bias. We have also measured the noise and estimated the peak detectivity to be 3×10⁸ cm·Hz^½·W⁻¹ at 1 V reverse bias and 30 K. A maximum internal quantum efficiency of 4.5% was derived from experiment. Both the photo and the dark transport have been successfully modeled as processes that involve direct and indirect field-assisted tunneling as well as thermionic emission. The best agreement with experiment was obtained when allowances were made for the non-uniformity of barrier widths and electric field heating of carriers above the lattice temperature. [reprint (PDF)]

Page 20 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)