Center for Quantum Devices - Most Downloaded Journal Articles

Page 16 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

14.	Multi-color 4–20 μm In-P-based Quantum Well Infrared Photodetectors C. Jelen, S. Slivken, G.J. Brown, and M. Razeghi SPIE Conference, San Jose, CA, -- January 27, 1999 ...[Visit Journal] In order to tune the wavelength of lattice-matched QWIP detectors over the range from 4 - 20 &mum, new designs are demonstrated for the first time which combine InGaAlAs and InGaAsP layers lattice-matched to InP and grown by gas-source molecular beam epitaxy. We demonstrate the first long-wavelength quantum well infrared photodetectors using the lattice-matched n-doped InGaAlAs/InP materials system. Samples with AlAs mole fractions of 0.0, 0.1, and 0.15 result in cutoff wavelengths of 8.5, 13.3, and 19.4 μm, respectively. A 45 degree facet coupled illumination responsivity of R equals 0.37 A/W and detectivity of D*(λ) equals 1x10⁹ cm·Hz^½·W^-1 at T = 77 K, for a cutoff wavelength λ_c equals 13.3 μm have been achieved. Based on the measured intersubband photoresponse wavelength, a null conduction band offset is expected for In_0.52Ga_0.21Al_0.27As/InP heterojunctions. We also report quantum well infrared photodetector structures of In_0.53Ga_0.47As/Al_0.48In_0.52As grown on InP substrate with photoresponse at 4 μm suitable for mid-wavelength infrared detectors. These detectors exhibit a constant peak responsivity of 30 mA/W independent of temperature in the range from T equals 77 K to T equals 200 K. Combining these two materials, we report the first multispectral detectors that combine lattice-matched quantum wells of InGaAs/InAlAs and InGaAs/InP. Utilizing two contacts, a voltage tunable detector with (lambda) p equals 8 micrometer at a bias of V equals 5 V and λ_p equals 4 μm at V equals 10 V is demonstrated. [reprint (PDF)]
14.	High-performance bias-selectable dual-band mid-/long-wavelength infrared photodetectors and focal plane arrays based on InAs/GaSb Type-II superlattices M. Razeghi; A. Haddadi; A.M. Hoang; G. Chen; S. Ramezani-Darvish; P. Bijjam Proc. SPIE 8704, Infrared Technology and Applications XXXIX, 87040S (June 11, 2013)-- June 11, 2013 ...[Visit Journal] We report a bias selectable dual-band mid-wave infrared (MWIR) and long-wave infrared (LWIR) co-located detector with 3 μm active region thickness per channel that is highly selective and can perform under high operating temperatures for the MWIR band. Under back-side illumination, a temperature evolution study of the MWIR detector's electro-optical performance found the 300 K background-limit with 2π field-of-view to be achieved below operating temperatures of 160 K, at which the temperature's 50% cutoff wavelength was 5.2 μm. The measured current reached the system limit of 0.1 pA at 110 K for 30 μm pixel-sized diodes. At 77 K, where the LWIR channel operated with a 50% cutoff wavelength at 11.2 μm, an LWIR selectivity of ∼17% was achieved in the MWIR wave band between 3 and 4.7 μm, making the detector highly selective. [reprint (PDF)]
14.	High quantum efficiency back-illuminated GaN avalanche photodiodes C. Bayram, J.L. Pau, R. McClintock, M. Razeghi, M.P. Ulmer, and D. Silversmith Applied Physics Letters, Vol. 93, No. 21, p. 211107-1-- November 24, 2008 ...[Visit Journal] Back-illuminated avalanche photodiodes (APDs) composed of heterojunctions of either p-GaN/i-GaN/n-AlGaN or p-GaN/i-GaN/n-GaN/n-AlGaN were fabricated on AlN templates. At low voltage, an external quantum efficiency of 57% at 352 nm with a bandpass response was achieved by using AlGaN in the n-layer. Dependency of gain and leakage current on mesa area for these heterojunction APDs were studied. Back-illumination via different wavelength sources was used to demonstrate the advantages of hole-initiated multiplication in GaN APDs. [reprint (PDF)]
14.	Negative luminescence of long-wavelength InAs/GaSb superlattice photodiodes D. Hoffman, A. Hood, Y. Wei, A. Gin, F. Fuchs, and M. Razeghi Applied Physics Letters 87 (20)-- November 14, 2005 ...[Visit Journal] The electrically pumped emission behavior of binary type-II InAs/GaSb superlattice photodiodes has been studied in the spectral range between 8 µm and 13 µm. With a radiometric calibration of the experimental setup, the internal and external quantum efficiency has been determined in the temperature range between 80 K and 300 K for both, the negative and positive luminescence. The negative luminescence efficiency approaches values as high as 35% without antireflection coating. The temperature dependence of the internal quantum efficiency near zero-bias voltage allows for the determination of the electron-hole-electron Auger recombination coefficient of Γ_n=1×10²⁴ cm⁶ s^–1. [reprint (PDF)]
14.	Extended electrical tuning of quantum cascade lasers with digital concatenated gratings S. Slivken, N. Bandyopadhyay, Y. Bai, Q. Y. Lu, and M. Razeghi Appl. Phys. Lett. 103, 231110 (2013)-- December 6, 2013 ...[Visit Journal] In this report, the sampled grating distributed feedback laser architecture is modified with digital concatenated gratings to partially compensate for the wavelength dependence of optical gain in a standard high efficiency quantum cascade laser core. This allows equalization of laser threshold over a wide wavelength range and demonstration of wide electrical tuning. With only two control currents, a full tuning range of 500 nm (236 cm⁻¹) has been demonstrated. Emission is single mode, with a side mode suppression of >20 dB. [reprint (PDF)]
14.	Type-II Superlattices and Quantum Cascade Lasers for MWIR and LWIR Free-Space Communications A. Hood, A. Evans and M. Razeghi SPIE Conference, January 20-25, 2008, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices V, Vol. 6900, p. 690005-1-9.-- February 1, 2008 ...[Visit Journal] Free-space optical communications has recently been touted as a solution to the "last mile" bottleneck of high-speed data networks providing highly secure, short to long range, and high-bandwidth connections. However, commercial near infrared systems experience atmospheric scattering losses and scintillation effects which can adversely affect a link's operating budget. By moving the operating wavelength into the mid- or long-wavelength infrared enhanced link uptimes and increased operating range can be achieved due to less susceptibility to atmospheric affects. The combination of room-temperature, continuous-wave, high-power quantum cascade lasers and high operating temperature type-II superlattice photodetectors offers the benefits of mid- and long-wavelength infrared systems as well as practical operating conditions for next generation free-space communications systems. [reprint (PDF)]
14.	Two‐dimensional electron gases in quantum well and superlattices of Ga0.25In0.75As0.50P0.50/InP heterostructures grown by low pressure metalorganic chemical vapor deposition M. Razeghi; J. P. Duchemin; J. C. Portal Appl. Phys. Lett. 46 (1): 46–48 (1985)-- January 1, 1985 ...[Visit Journal] We report the first observation of a two‐dimensional electron gas from Shubnikov–de Haas experiments, in a Ga0.25In0.75As0.50P0.50‐InP heterojunction, multi‐quantum well, and superlattices grown by metalorganic chemical vapor deposition at reduced pressure. [reprint (PDF)]
14.	Monolithic integrated photoreceiver for 1.3–1.55‐μm wavelengths: Association of a Schottky photodiode and a field‐effect transistor on GaInP‐GaInAs heteroepitaxy A. Hosseini Therani; D. Decoster; J. P. Vilcot; M. Razeghi J. Appl. Phys. 64, 2215–2218 (1988) -- March 24, 1988 ...[Visit Journal] We present a monolithic integrated circuit associating a Schottky photodiode and a field-effect transistor which has been fabricated, for the first time, on G8.0.49 InO.51 P /GaO,47 Ino.53 As strained heteroepitaxiaI material. Static, dynamic, and noise properties of the Schottky photodiode, the field-effect transistor, and the integrated circuit have been investigated and are reported. As an example, dynamic responsivity up to 50 A/W can be achieved at 1.3-pm wavelength for the integrated photoreceiver. The performance of the device is discussed, taking into account the integrated circuit design and the main characteristics of the material. [reprint (PDF)]
14.	Negative luminescence of InAs/GaSb superlattice photodiodes F. Fuchs, D. Hoffman, A. Gin, A. Hood, Y. Wei, and M. Razeghi Phys. Stat. Sol. C 3 (3)-- February 22, 2006 ...[Visit Journal] The emission behaviour of InAs/GaSb superlattice photodiodes has been studied in the spectral range between 8 µm and 13 μm. With a radiometric calibration of the experimental set-up the internal quantum efficiency has been determined in the temperature range between 80 K and 300 K for both, the negative and positive luminescence. The quantitative analysis of the internal quantum efficiency of the non-equilibrium radiation enables the determination of the Auger coefficient. [reprint (PDF)]
14.	The correlation between x-ray diffraction patterns and strain distribution inside GaInP/GaAs superlattices X.G. He, M. Erdtmann, R. Williams, S. Kim, and M. Razeghi Applied Physics Letters 65 (22)-- November 28, 1994 ...[Visit Journal] Strong correlation between x‐ray diffraction characteristics and strain distribution inside GaInP/GaAs superlattices has been reported. It is found that the symmetry of (002) diffraction patterns can be used to evaluate the interface strain status. A sample with no interfacial strains has a symmetric (002) diffraction pattern and weak (004) diffraction pattern. It is also demonstrated that strain distribution in superlattices can be readily estimated qualitatively by analyzing x-ray diffraction patterns. [reprint (PDF)]
14.	Room temperature neagtive differential resistance characteristics of polar III-nitride resonant tunneling diodes C. Bayram, Z. Vashaei, and M. Razeghi Applied Physics Letters, Vol. 97, No. 9, p. 092104-1-- August 30, 2010 ...[Visit Journal] III-nitride resonant tunneling diodes (RTDs), consisting Al_0.2Ga_0.8N/GaN double-barrier (DB) active layers, were grown on c-plane lateral epitaxial overgrowth (LEO) GaN/sapphire and c-plane freestanding (FS) GaN. RTDs on both templates, fabricated into mesa diameters ranging from 5 to 35 μm, showed negative differential resistance (NDR) at room temperature. NDR characteristics (voltage and current density at NDR onset and current-peak-to-valley ratio) were analyzed and reported as a function of device size and substrate choice. Our results show that LEO RTDs perform as well as FS ones and DB active layer design and quality have been the bottlenecks in III-nitride RTDs. [reprint (PDF)]
14.	First cw operation of a Ga0.25In0.75As0.5P0.5‐InP laser on a silicon substrate M. Razeghi; M. Defour; R. Blondeau; F. Omnes; P. Maurel; O. Acher; F. Brillouet; J. C. C‐Fan; J. Salerno Appl. Phys. Lett. 53, 2389–2390 (1988) -- December 12, 1988 ...[Visit Journal] We report the first successful room-temperature cw operations of a GaO. 25 1110.75 ASo. 5 po. s -InP buried ridge structure laser emitting at 1.3 f-tm grown by two-step low-pressure metalorganic chemical vapor deposition on a silicon substrate. An output power of 20 m W with an external quantum efficiency of 16% at room temperature has been obtained. A threshold current as low as 45 rnA under cw operation at room temperature has been measured. The first cw aging test at room temperature, at 2 mW during 5 h, shows a very low degradation (Ill 11,;;5%). [reprint (PDF)]
14.	Geiger-Mode Operation of AlGaN Avalanche Photodiodes at 255 nm Lakshay Gautam, Alexandre Guillaume Jaud, Junhee Lee, Gail J. Brown, Manijeh Razeghi Published in: IEEE Journal of Quantum Electronics ( Volume: 57, Issue: 2, April 2021) ...[Visit Journal] We report the Geiger mode operation of back-illuminated AlGaN avalanche photodiodes. The devices were fabricated on transparent AlN templates specifically for back-illumination to leverage hole-initiated multiplication. The spectral response was analyzed with a peak detection wavelength of 255 nm with an external quantum efficiency of ~14% at zero bias. Low-photon detection capabilities were demonstrated in devices with areas 25 μm×25 μm. Single photon detection efficiencies of ~5% were achieved. [reprint (PDF)]
14.	Crack-free AlGaN for solar-blind focal plane arrays through reduced area expitaxy E. Cicek, R. McClintock, Z. Vashaei, Y. Zhang, S. Gautier, C.Y. Cho and M. Razeghi Applied Physics Letters, Vol. 102, No. 05, p. 051102-1-- February 4, 2013 ...[Visit Journal] We report on crack reduction for solar-blind ultraviolet detectors via the use of a reduced area epitaxy (RAE) method to regrow on patterned AlN templates. With the RAE method, a pre-deposited AlN template is patterned into isolated mesas in order to reduce the formation of cracks in the subsequently grown high Al-content Al_xGa_1−xN structure. By restricting the lateral dimensions of the epitaxial growth area, the biaxial strain is relaxed by the edges of the patterned squares, which resulted in ∼97% of the pixels being crack-free. After successful implementation of RAE method, we studied the optical characteristics, the external quantum efficiency, and responsivity of average pixel-sized detectors of the patterned sample increased from 38% and 86.2 mA/W to 57% and 129.4 mA/W, respectively, as the reverse bias is increased from 0 V to 5 V. Finally, we discussed the possibility of extending this approach for focal plane array, where crack-free large area material is necessary for high quality imaging. [reprint (PDF)]
14.	Injector doping level dependent continuous-wave operation of InP-based QCLs at λ~ 7.3 µm above room temperature J.S. Yu, S. Slivken, and M. Razeghi Semiconductor Science and Technology (SST), Vol. 25, No. 12, p. 125015-- December 1, 2010 ...[Visit Journal] We report the continuous-wave (CW) operation of InGaAs/InAlAs quantum cascade lasers (QCLs) operating at λ ~ 7.3 µm above room temperature. The injector doping level–dependent CW characteristics above room temperature are investigated for doping densities between 7 × 10¹⁶ cm⁻³ and 2 × 10¹⁷ cm⁻³. The device performance, i.e. threshold current density, output power, operating temperature and characteristic temperature, depends strongly on the injector doping density. For a relatively low injector doping density of 7 × 10¹⁶ cm⁻³, a high-reflectivity-coated 10 µm wide and 4 mm long laser exhibits an improved device performance with an output power of 152 mW and a threshold current density of 1.37 kA cm⁻² at 298 K under CW mode, operating up to 343 K. The thermal characteristics are also analyzed by the estimation from the experimentally measured data for the QCLs with different injector doping densities. [reprint (PDF)]
14.	Electrically pumped photonic crystal distributed feedback quantum cascade lasers Y. Bai, S.R. Darvish, S. Slivken, P. Sung, J. Nguyen, A. Evans, W. Zhang, and M. Razeghi Applied Physics Letters, Vol. 91, No. 14, p. 141123-1-- October 1, 2007 ...[Visit Journal] We demonstrate electrically pumped, room temperature, single mode operation of photonic crystal distributed feedback (PCDFB) quantum cascade lasers emitting at ~4.75 µm. Ridge waveguides of 100 µm width were fabricated with both PCDFB and Fabry-Pérot feedback mechanisms. The Fabry-Pérot device has a broad emitting spectrum and a double lobed far-field character. The PCDFB device, as expected, has primarily a single spectral mode and a diffraction limited far field characteristic with a full angular width at half maximum of 2.4°. This accomplishment represents the first step in power scaling of single mode, midinfrared laser diodes operating at room temperature. [reprint (PDF)]
14.	Anomalous Hall Effect in InSb Layers Grown by MOCVD on GaAs Substrates C. Besikci, Y.H. Choi, R. Sudharsanan, and M. Razeghi Journal of Applied Physics 73 (10)-- May 15, 1993 ...[Visit Journal] InSb epitaxial layers have been grown on GaAs substrates by low‐pressure metalorganic chemical vapor deposition. A 3.15 μm thick film yielded an x‐ray full width at half maximum of 171 arcsec. A Hall mobility of 76 200 cm²/V· s at 240 K and a full width at half maximum of 174 arcsec have been measured for a 4.85 μm thick epilayer. Measured Hall data have shown anomalous behavior. A decrease in Hall mobility with decreasing temperature has been observed and room‐temperature Hall mobility has increased with thickness. In order to explain the anomalous Hall data, and the thickness dependence of the measured parameters, the Hall coefficient and Hall mobility have been simulated using a three‐layer model including a surface layer, a bulklike layer, and an interface layer with a high density of defects. Theoretical analysis has shown that anomalous behavior can be attributed to donor-like defects caused by the large lattice mismatch and to a surface layer which dominates the transport in the material at low temperatures. [reprint (PDF)]
14.	Ultraviolet avalanche photodiodes Ryan McClintock ; Manijeh Razeghi Proc. SPIE 9555, Optical Sensing, Imaging, and Photon Counting: Nanostructured Devices and Applications, 95550B -- August 28, 2015 ...[Visit Journal] The III-Nitride material system is rapidly maturing; having proved itself as a material for LEDs and laser, and now finding use in the area of UV photodetectors. However, many UV applications are still dominated by the use of photomultiplier tubes (PMT). PMTs are capable of obtaining very high sensitivity using internal electron multiplication gain (typically ~106). It is highly desirable to develop a compact semiconductor-based photodetector capable of realizing this level of sensitivity. In principle, this can be obtained in III-Nitrides by taking advantage of avalanche multiplication under high electric fields – typically 2.7 MV/cm, which with proper design can correspond to an external reverse bias of less than 100 volts. In this talk, we review the current state-of-the-art in III-Nitride solar- and visible-blind APDs, and present our latest results on GaN APDs grown on both conventional sapphire and low dislocation density free-standing c- and m-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs were compared. The spectral response and Geiger-mode photon counting performance of UV APDs are studied under low photon fluxes, with single photon detection capabilities as much as 30% being demonstrated in smaller devices. Geiger-mode operation conditions are optimized for enhanced SPDE. [reprint (PDF)]
14.	Ridge-Width Dependence on High-Temperature Continuous-Wave Quantum-Cascade Laser Operation S. Slivken, J.S. Yu, A. Evans, L. Doris, J. David, and M. Razeghi IEEE Photonics Technology Letters, 16 (3)-- March 1, 2004 ...[Visit Journal] We report continuous-wave (CW) operation of quantum-cascade lasers (λ=6 μm) up to a temperature of 313 K (40°C). The maximum CW optical output powers range from 212 mW at 288 K to 22 mW at 313 K and are achieved with threshold current densities of 2.21 and 3.11 kA/cm2, respectively, for a high-reflectivity-coated 12-μm-wide and 2-mm-long laser. At room temperature (298 K), the power output is 145 mW at 0.87 A, corresponding to a power conversion efficiency of 1.68%. The maximum CW operating temperature of double-channel ridge waveguide lasers mounted epilayer-up on copper heatsinks is analyzed in terms of the ridge width, which is varied between 12 and 40 μm. A clear trend of improved performance is observed as the ridge narrows. [reprint (PDF)]
14.	High-power laser diodes based on InGaAsP alloys M. Razeghi Nature, Vol.369, p.631-633-- June 23, 1994 ...[Visit Journal] HIGH-POWER, high-coherence solid-state lasers, based on dielectric materials such as ruby or Nd:YAG (yttrium aluminium garnet), have many civilian and military applications. The active media in these lasers are insulating, and must therefore be excited (or ‘pumped’) by optical, rather than electrical, means. Conventional gas-discharge lamps can be used as the pumping source, but semiconductor diode lasers are more efficient, as their wavelength can be tailored to match the absorption properties of the lasing material. Semiconducting AlGaAs alloys are widely used for this purpose, but oxidation of the aluminium and the spreading of defects during device operation limit the lifetime of the diodes3, and hence the reliability of the system as a whole. Aluminium-free InGaAsP compounds, on the other hand, do not have these lifetime-limiting properties. We report here the fabrication of high-power lasers based on InGaAsP (lattice-matched to GaAs substrates), which operate over the same wavelength range as conventional AlGaAs laser diodes and show significantly improved reliability. The other optical and electrical properties of these diodes are either comparable or superior to those of the AlGaAs system. [reprint (PDF)]
14.	A detailed analysis of carrier transport in InAs0.3Sb0.7 layers grown on GaAs substrates by metalorganic chemical vapor deposition C. Besikci, Y.H. Choi, G. Labeyrie, E. Bigan and M. Razeghi with J.B. Cohen, J. Carsello, and V.P. Dravid Journal of Applied Physics 76 (10)-- November 15, 1994 ...[Visit Journal] InAs_0.3Sb_0.7 layers with mirrorlike morphology have been grown on GaAs substrates by low‐pressure metalorganic chemical vapor deposition. A room‐temperature electron Hall mobility of 2×10⁴ cm²/V· s has been obtained for a 2 μm thick layer. Low‐temperature resistivity of the layers depended on TMIn flow rate and layer thickness. Hall mobility decreased monotonically with decreasing temperature below 300 K. A 77 K conductivity profile has shown an anomalous increase in the sample conductivity with decreasing thickness except in the near vicinity of the heterointerface. In order to interpret the experimental data, the effects of different scattering mechanisms on carrier mobility have been calculated, and the influences of the lattice mismatch and surface conduction on the Hall measurements have been investigated by applying a three‐layer Hall‐effect model. Experimental and theoretical results suggest that the combined effects of the dislocations generated by the large lattice mismatch and strong surface inversion may lead to deceptive Hall measurements by reflecting typical n‐type behavior for a p‐type sample, and the measured carrier concentration may considerably be affected by the surface conduction up to near room temperature. A quantitative analysis of dislocation scattering has shown significant degradation in electron mobility for dislocation densities above 10⁷ cm⁻². The effects of dislocation scattering on hole mobility have been found to be less severe. It has also been observed that there is a critical epilayer thickness (∼1 μm) below which the surface electron mobility is limited by dislocation scattering. [reprint (PDF)]
14.	Efficiency of photoluminescence and excess carrier confinement in InGaAsP/GaAs structures prepared by metal-organic chemical vapor deposition J. Diaz, H.J. Yi, M. Erdtmann, X. He, E. Kolev, D. Garbuzov, E. Bigan, and M. Razeghi Journal of Applied Physics 76 (2)-- July 15, 1994 ...[Visit Journal] Special double‐ and separate‐confinement InGaAsP/GaAs heterostructures intended for photoluminescence measurements have been grown by low‐pressure metal‐organic chemical‐vapor deposition. The band gap of the active region quaternary material was close to 1.5 eV, and the waveguide of the separate‐confinement structures was near 1.8 eV. Measurement of the integrated luminescence efficiency at 300 K has shown that over a wide range of excitation level (10–10³ W/cm²) radiative transitions are the dominant mechanism for excess carrier recombination in the active region of the structures studied. As determined by spectral measurements, the excess carrier concentration in the waveguide of the separate‐confinement heterostructures and the intensity of the waveguide emission band correspond to a condition of thermal equilibrium of the excess carrier populations in the active region and the waveguide. The ratio of the intensity of the waveguide emission to the active region emission fits a model which assumes that the barrier height for minority carriers (holes) is equal to the difference in band gaps between the active region and the waveguide region. [reprint (PDF)]
14.	Very high quality p-type Al_xGa_1-xN/GaN superlattice A. Yasan and M. Razeghi special ISDRS issue of Solid State Electronics Journal, 47-- January 1, 2003 ...[Visit Journal] Very high quality p-type Al_xGa_1−xN/GaN superlattice has been achieved through optimization of Mg flow and period of superlattice. Theoretical model was used to optimize the structure of superlattice by choosing suitable Al compositions and superlattice periods. The experiments show that for x=0.26, the resistivity is as low as 0.19 Ω cm and hole concentration is as high as 4.2×10¹⁸ cm⁻³, the highest values ever reported for p-type AlGaN/GaN superlattices. Hall effect measurement and admittance spectroscopy on the samples confirm the high quality of the superlattices. The activation energy calculated for p-type GaN and p-type A_0.1Ga_0.9N/GaN superlattice is estimated to be not, vert, similar 125 and 3 meV respectively. [reprint (PDF)]
14.	Growth of Deep UV Light Emitting Diodes by Metalorganic Chemical Vapor Deposition A. Yasan, R. McClintock, K. Mayes, D. Shiell, S. Darvish, P. Kung and M. Razeghi SPIE Conference, Jose, CA, Vol. 5359, pp. 400-- January 25, 2004 ...[Visit Journal] We demonstrate high power AlGaN based ultraviolet light-emitting diodes (UV LEDs) with an emission wavelength of 280 nm using an asymmetric single quantum well active layer configuration on top of a high-quality AlGaN/AlN template layer grown by metalorganic chemical vapor deposition (MOCVD). An output power of 1.8 mW at a pulsed current of 400 mA was achieved for a single 300 µm × 300 µm diode. This device reached a high peak external quantum efficiency of 0.24% at 40 mA. An array of four diodes produced 6.5 mW at 880 mA of pulsed current. [reprint (PDF)]
14.	Al_xGa_1−xN-based solar-blind ultraviolet photodetector based on lateral epitaxial overgrowth of AlN on Si substrate E. Cicek, R. McClintock, C. Y. Cho, B. Rahnema, and M. Razeghi Appl. Phys. Lett. 103, 181113 (2013)-- October 30, 2013 ...[Visit Journal] We report on Al_xGa_1−xN-based solar-blind ultraviolet (UV) photodetector (PD) grown on Si(111) substrate. First, Si(111) substrate is patterned, and then metalorganic chemical vapor deposition is implemented for a fully-coalesced ∼8.5 μm AlN template layer via a pulsed atomic layer epitaxial growth technique. A back-illuminated p-i-n PD structure is subsequently grown on the high quality AlN template layer. After processing and implementation of Si(111) substrate removal, the optical and electrical characteristic of PDs are studied. Solar-blind operation is observed throughout the array; at the peak detection wavelength of 290 nm, 625 μm² area PD showed unbiased peak external quantum efficiency and responsivity of ∼7% and 18.3 mA/W, respectively, with a UV and visible rejection ratio of more than three orders of magnitude. Electrical measurements yielded a low-dark current density below 1.6 × 10⁻⁸ A/cm² at 10 V reverse bias. [reprint (PDF)]

Page 16 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)