Center for Quantum Devices - Most Downloaded Journal Articles

Page 13 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

15.	2.4 W room temperature continuous wave operation of distributed feedback quantum cascade lasers Q.Y. Lu, Y. Bai, N. Bandyopadhyay, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 98, No. 18, p. 181106-1-- May 4, 2011 ...[Visit Journal] We demonstrate high power continuous-wave room-temperature operation surface-grating distributed feedback quantum cascade lasers at 4.8 μm. High power single mode operation benefits from a combination of high-reflection and antireflection coatings. Maximum single-facet continuous-wave output power of 2.4 W and peak wall plug efficiency of 10% from one facet is obtained at 298 K. Single mode operation with a side mode suppression ratio of 30 dB and single-lobed far field without beam steering is observed. [reprint (PDF)]
15.	Extended short wavelength infrared heterojunction phototransistors based on type II superlattices Arash Dehzangi , Ryan McClintock, Donghai Wu , Abbas Haddadi, Romain Chevallier , and Manijeh Razeghi Applied Physics Letters 114, 191109-- May 17, 2019 ...[Visit Journal] A two terminal extended short wavelength infrared heterojunction phototransistor based on type-II InAs/AlSb/GaSb on a GaSb substrate is designed, fabricated, and investigated. With the base thickness of 40 nm, the device exhibited a 100% cut-off wavelength of 2.3 λ at 300 K. The saturated peak responsivity value is 320.5 A/W at 300 K, under front-side illumination without any antireflection coating. A saturated optical gain of 245 at 300K was measured. At the same temperature, the device exhibited a collector dark current density (at unity optical gain) and a DC current gain of 7.8 X 10³ A/cm² and 1100, respectively. The device exhibited a saturated dark current shot noise limited specific detectivity of 4.9 X 10¹¹ cm·Hz^½/W at 300 K which remains constant over a broad range of wavelengths and applied biases. [reprint (PDF)]
15.	High Power 280 nm AlGaN Light Emitting Diodes Based on an Asymmetric Single Quantum Well K. Mayes, A. Yasan, R. McClintock, D. Shiell, S.R. Darvish, P. Kung, and M. Razeghi Applied Physics Letters, 84 (7)-- February 16, 2004 ...[Visit Journal] We demonstrate high-power AlGaN-based ultraviolet light-emitting diodes grown on sapphire with an emission wavelength of 280 nm using an asymmetric single-quantum-well active layer configuration on top of a high-quality AlGaN/AlN template layer. An output power of 1.8 mW at a pulsed current of 400 mA was achieved for a single 300 µm×300 µm diode. This device reached a high peak external quantum efficiency of 0.24% at 40 mA. An array of four diodes produced 6.5 mW at 880 mA of pulsed current. [reprint (PDF)]
15.	Development of high power, InP-based quantum cascade lasers on alternative epitaxial platforms Steven Slivken, Nirajman Shrestha, Manijeh Razeghi Proc. of SPIE Vol. 12895, Quantum Sensing and Nano Electronics and Photonics XX, 1289503 (28 January - 1 February 2024, San Francisco) doi: 10.1117/12.3009335 ...[Visit Journal] In this talk, challenges and solutions associated with the monolithic, epitaxial integration of mid- and longwave- infrared, InP-based quantum cascade lasers on GaAs and Si wafers will be discussed. Initial results, including room temperature, high power, and continuous wave operation, will be described. [reprint (PDF)]
15.	Growth and characterization of InP using metalorganic chemical vapor deposition at reduced pressure M. Razeghi, J.P. Duchemin M. Razeghi, J.P. Duchemin, Growth and characterization of InP using metalorganic chemical vapor deposition at reduced pressure, Journal of Crystal Growth, Volume 64, Issue 1, 1983, Pages 76-82,-- November 1, 1983 ...[Visit Journal] M. Razeghi, J.P. Duchemin, Growth and characterization of InP using metalorganic chemical vapor deposition at reduced pressure, Journal of Crystal Growth, Volume 64, Issue 1, 1983, Pages 76-82, [reprint (PDF)]
15.	Thin film transistors with wurtzite ZnO channels grown on Si₃N₄/SiO₂/Si (111) substrates by pulsed laser deposition D.J. Rogers; V.E. Sandana; F. Hosseini Teherani; M. Razeghi Proc. SPIE 7603, Oxide-based Materials and Devices, 760318 (March 02, 2010)-- March 7, 2010 ...[Visit Journal] Thin Film Transistors (TFT) were made by growing ZnO on Si₃N₄/SiO₂/Si (111) substrates by pulsed laser deposition. X-ray diffraction and scanning electron microscope studies revealed the ZnO to have a polycrystalline wurtzite structure with a smooth surface, good crystallographic quality and a strong preferential c-axis orientation. Transmission studies in similar ZnO layers on glass substrates showed high transmission over the whole visible spectrum. Electrical measurements of a back gate geometry FET showed an enhancement-mode response with hard saturation, mA range Id and a V_ON ∼ 0V. When scaled down, such TFTs may be of interest for high frequency applications. [reprint (PDF)]
15.	Low pressure metalorganic chemical vapor deposition of InP and related compounds M. Razeghi, M. A. Poisson, J. P. Larivain & J. P. Duchemin Razeghi, M., Poisson, M.A., Larivain, J.P. et al. Low pressure metalorganic chemical vapor deposition of InP and related compounds. J. Electron. Mater. 12, 371–395 (1983). https://doi.org/10.1007/BF02651138-- March 1, 1983 ...[Visit Journal] The low pressure metalorganic chemical vapor deposition epitaxial growth and characterization of InP, Ga0.47In0.53 As and GaxIn1-xAsyP1-y, lattice-matched to InP substrate are described. The layers were found to have the same etch pit density (EPD) as the substrate. The best mobility obtained for InP was 5300 cm2 V−1S−1 at 300 K and 58 900 cm2 V−1 S−1 at 772K, and for GaInAs was 11900 cm2 V−1 S−1 at 300 K, 54 600 cm2 V−1 S−1 at 77 K and 90 000 cm V−1S−1 at 2°K. We report the first successful growth of a GaInAs-InP superlattice and the enhanced mobility of a two dimensional electron gas at a GaInAs -InP heterojunction grown by LP-MO CVD. LP MO CVD material has been used for GaInAsPInP, DH lasers emitting at 1.3 um and 1.5 um. These devices exhibit a low threshold current, a slightly higher than liquid phase epitaxy devices and a high differential quantum efficiency of 60%. Fundamental transverse mode oscillation has been achieved up to a power outpout of 10 mW. Threshold currents as low as 200 mA dc have been measured for devices with a stripe width of 9 um and a cavity length of 300 um for emission at 1.5 um. Values of T in the range 64–80 C have been obtained. Preliminary life testing has been carried out at room temperature on a few laser diodes (λ = 1.5μm). Operation at constant current for severalthousand hours has been achieved with no change in the threshold current. [reprint (PDF)]
15.	Persistent photoconductivity in Ga0.49In0.51P/GaAs heterojunctions S. Ben Amor; L. Dmowski; J. C. Portal; N. J. Pulsford; R. J. Nicholas; J. Singleton; M. Razeghi J. Appl. Phys. 65, 2756–2760 (1989-- November 18, 1988 ...[Visit Journal] We have studied the persistent photoconductivity (PPC) effect in Ga0.49 Ino. sl P IGaAs heterostructures. Through time- and temperature-dependent Hall effect, we observe very small relaxation rates and the PPC remains observable at room temperature. Optical experiments show an optical energy threshold of 1.15 e V and an infrared quenching of the ppc. Thermal cycling of the samples strongly affects the PPC and the quenching temperature. The center responsible for the observed PPC, therefore, appears related to defects, Most of our observations are qualitatively understood in a large lattice relaxation DX-like center approach. However, the origin of the high quenching temperature remains to be explained. [reprint (PDF)]
15.	Recent advances of terahertz quantum cascade lasers Manijeh Razeghi Proc. SPIE 8119, Terahertz Emitters, Receivers, and Applications II, 81190D (September 07, 2011)-- November 7, 2011 ...[Visit Journal] In the past decade, tremendous development has been made in GaAs/AlGaAs based THz quantum cascade laser (QCLs), however, the maximum operating temperature is still limited below 200 K (without magnetic field). THz QCL based on difference frequency generation (DFG) represents a viable technology for room temperature operation. Recently, we have demonstrated room temperature THz emission (∼ 4 THz) up to 8.5 μW with a power conversion efficiency of 10 μW/W². A dual-period distributed feedback grating is used to filter the mid-infrared spectra in favor of an extremely narrow THz linewidth of 6.6 GHz. [reprint (PDF)]
15.	Development of Quantum Well Infrared Photodetectors at the Center for Quantum Devices M. Razeghi, M. Erdtmann, C. Jelen, J. Diaz, F. Guastavino, G.J. Brown, and Y.S. Park Infrared Physics and Technology 42 (3-5)-- January 1, 2001 ...[Visit Journal] Results of detector characterization are presented for quantum well infrared photodetectors (QWIPs) fabricated from a variety of III-V material systems lattice-matched to GaAs or InP substrate, p-Type GaAs/GaInP QWIPs show background limited performance up to temperatures of 120 K, while p-type GaInAsP/GaInAsP QWIPs exhibit broadband response from lambda = 2.5-10 mum. n-Type GaAs/GaInP QWIPs are sensitive deep into the VLWIR with very low dark current. Extremely large responsivities of 33.2 AW(-1) were obtained from n-type GaInAs/InP QWIPs operating at lambda = 9 mum. Devices made from n-type AlGaInAs/InP and GaInAs/AlInAs have also been realized that extend the wavelength range of sensitivity from 3 mum out to 20 mum while remaining lattice-matched to InP. Lattice-matched multispectral detectors are demonstrated for sensitivity at both 4 and 8.5 mum Localized epitaxy of GaInAs/InP superlattice structures lattice-matched to InP was performed on Si substrate for the purpose of monolithic integration of III-V QWIPs with Si-based read-out integrated circuitry. [reprint (PDF)]
15.	Geiger-mode operation of back-illuminated GaN avalanche photodiodes J. L. Pau, R. McClintock, K. Minder, C. Bayram, P. Kung, M. Razeghi, E. Muñoz, and D. Silversmith Applied Physics Letters, Vol. 91, No. 04, p. 041104 -1-- July 23, 2007 ...[Visit Journal] We report the Geiger-mode operation of back-illuminated GaN avalanche photodiodes fabricated on transparent AlN templates specifically for back illumination in order to enhance hole-initiated multiplication. The spectral response in Geiger-mode operation was analyzed under low photon fluxes. Single photon detection capabilities were demonstrated in devices with areas ranging from 225 to 14,063 µm². Single photon detection efficiency of 20% and dark count rate < 10 kHz were achieved in the smallest devices. [reprint (PDF)]
15.	Ultrafast Pulse Generation from Quantum Cascade Lasers Feihu Wang, Xiaoqiong Qi, Zhichao Chen, Manijeh Razeghi, and Sukhdeep Dhillon Wang, F.; Qi, X.; Chen, Z.; Razeghi, M.; Dhillon, S. Ultrafast Pulse Generation from Quantum Cascade Lasers. Micromachines 2022, 13, 2063. https://doi.org/10.3390/ mi13122063 ...[Visit Journal] Quantum cascade lasers (QCLs) have broken the spectral barriers of semiconductor lasers and enabled a range of applications in the mid-infrared (MIR) and terahertz (THz) regimes. However, until recently, generating ultrashort and intense pulses from QCLs has been difficult. This would be useful to study ultrafast processes in MIR and THz using the targeted wavelength-by-design properties of QCLs. Since the first demonstration in 2009, mode-locking of QCLs has undergone considerable development in the past decade, which includes revealing the underlying mechanism of pulse formation, the development of an ultrafast THz detection technique, and the invention of novel pulse compression technology, etc. Here, we review the history and recent progress of ultrafast pulse generation from QCLs in both the THz and MIR regimes. [reprint (PDF)]
15.	Graphene versus oxides for transparent electrode applications Sandana, V. E.; Rogers, D. J.; Teherani, F. Hosseini; Bove, P.; Razeghi, M. Proc. SPIE 8626, Oxide-based Materials and Devices IV, 862603 (March 18, 2013)-- March 18, 2013 ...[Visit Journal] Due to their combination of good electrical conductivity and optical transparency, Transparent Conducting Oxides (TCOs) are the most common choice as transparent electrodes for optoelectronics applications. In particular, devices, such as LEDs, LCDs, touch screens and solar cells typically employ indium tin oxide. However, indium has some significant drawbacks, including toxicity issues (which are hampering manufacturing), an increasing rarefication (due to a combination of relative scarcity and increasing demand [1]) and resulting price increases. Moreover, there is no satisfactory option at the moment for use as a p-type transparent contact. Thus alternative materials solutions are actively being sought. This review will compare the performance and perspectives of graphene with respect to TCOs for use in transparent conductor applications. [reprint (PDF)]
15.	Demonstration of negative differential resistance in GaN/AlN resonant tunneling didoes at room temperature Z. Vashaei, C. Bayram and M. Razeghi Journal of Applied Physics, Vol. 107, No. 8, p. 083505-- April 15, 2010 ...[Visit Journal] GaN/AlN resonant tunneling diodes (RTD) were grown by metal-organic chemical vapor deposition (MOCVD) and negative differential resistance with peak-to-valley ratios as high as 2.15 at room temperature was demonstrated. Effect of material quality on RTDs’ performance was investigated by growing RTD structures on AlN, GaN, and lateral epitaxial overgrowth GaN templates. Our results reveal that negative differential resistance characteristics of RTDs are very sensitive to material quality (such as surface roughness) and MOCVD is a suitable technique for III-nitride-based quantum devices. [reprint (PDF)]
15.	Recent Advances in InAs/GaSb Superlattices for Very Long Wavelength Infrared Detection G.J. Brown, F. Szmulowicz, K. Mahalingam, S. Houston, Y. Wei, A. Gin and M. Razeghi SPIE Conference, San Jose, CA, Vol. 4999, pp. 457-- January 27, 2003 ...[Visit Journal] New infrared (IR) detector materials with high sensitivity, multi-spectral capability, improved uniformity and lower manufacturing costs are required for numerous long and very long wavelength infrared imaging applications. One materials system has shown great theoretical and, more recently, experimental promise for these applications: InAs/In_xGa_1-xSb type-II superlattices. In the past few years, excellent results have been obtained on photoconductive and photodiode samples designed for infrared detection beyond 15 microns. The infrared properties of various compositions and designs of these type-II superlattices have been studied. The infrared photoresponse spectra are combined with quantum mechanical modeling of predicted absorption spectra to provide insight into the underlying physics behind the quantum sensing in these materials. Results for superlattice photodiodes with cut-off wavelengths as long as 25 microns are presented. [reprint (PDF)]
15.	Wafer-scale epitaxial lift-off of optoelectronic grade GaN from a GaN substrate using a sacrificial ZnO interlayer Akhil Rajan, David J Rogers, Cuong Ton-That, Liangchen Zhu, Matthew R Phillips, Suresh Sundaram, Simon Gautier, Tarik Moudakir, Youssef El-Gmili, Abdallah Ougazzaden, Vinod E Sandana, Ferechteh H Teherani, Philippe Bove, Kevin A Prior, Zakaria Djebbour, Ryan McClintock and Manijeh Razeghi Journal of Physics D: Applied Physics, Volume 49, Number 31 -- July 15, 2016 ...[Visit Journal] Full 2 inch GaN epilayers were lifted off GaN and c-sapphire substrates by preferential chemical dissolution of sacrificial ZnO underlayers. Modification of the standard epitaxial lift-off (ELO) process by supporting the wax host with a glass substrate proved key in enabling full wafer scale-up. Scanning electron microscopy and x-ray diffraction confirmed that intact epitaxial GaN had been transferred to the glass host. Depth-resolved cathodoluminescence (CL) analysis of the bottom surface of the lifted-off GaN layer revealed strong near-band-edge (3.33 eV) emission indicating a superior optical quality for the GaN which was lifted off the GaN substrate. This modified ELO approach demonstrates that previous theories proposing that wax host curling was necessary to keep the ELO etch channel open do not apply to the GaN/ZnO system. The unprecedented full wafer transfer of epitaxial GaN to an alternative support by ELO offers the perspective of accelerating industrial adoption of the expensive GaN substrate through cost-reducing recycling. [reprint (PDF)]
15.	Low frequency noise in 1024 x 1024 long wavelength infrared focal plane array base on Type-II InAs/GaSb superlattice A. Haddadi, S.R. Darvish, G. Chen, A.M. Hoang, B.M. Nguyen and M. Razeghi SPIE Proceedings, Vol. 8268, p. 82680X-- January 22, 2012 ...[Visit Journal] Recently, the type-II InAs/GaSb superlattice (T2SL) material platform is considered as a potential alternative for HgCdTe technology in long wavelength infrared (LWIR) imaging. This is due to the incredible growth in the understanding of its material properties and improvement of device processing which leads to design and fabrication of better devices. In this paper, we report electrical low frequency noise measurement on a high performance type-II InAs/GaSb superlattice 1024×1024 LWIR focal plane array. [reprint (PDF)]
15.	Modeling Type-II InAs/GaSb Superlattices Using Empirical Tight-Binding Method: New Aspects Y. Wei, M. Razeghi, G.J. Brown, and M.Z. Tidrow SPIE Conference, Jose, CA, Vol. 5359, pp. 301-- January 25, 2004 ...[Visit Journal] The recent advances in the experimental work on the Type-II InAs/GaSb superlattices necessitate a modeling that can handle arbitrary layer thickness as well as different types of interfaces in order to guide the superlattice design. The empirical tight-binding method (ETBM) is a very good candidate since it builds up the Hamiltonian atom by atom. There has been a lot of research work on the modeling of Type-II InAs/GaSb superlattices using the ETBM. However, different groups generate very different accuracy comparing with experimental results. We have recently identified two major aspects in the modeling: the antimony segregation and the interface effects. These two aspects turned out to be of crucial importance governing the superlattice properties, especially the bandgap. We build the superlattice Hamiltonian using antimony segregated atomic profile taking into account the interface. Our calculations agree with our experimental results within growth uncertainties. In addition we introduced the concept of Ga_xIn_1-x type interface engineering, which will add another design freedom especially in the mid-wavelength infrared range (3~7 µm) in orderto reduce the lattice mismatch. [reprint (PDF)]
15.	Electron capture processes in optically excited In0.53Ga 0.47As/InP quantum wells U. Cebulla, G. Bacher, A. Forchel, D. Schmitz, H. Jürgensen, M. Razeghi Appl. Phys. Lett. 55, 933–935 (1989)-- September 4, 1989* ...[Visit Journal] We have performed picosecond time-resolved measurements on Ir:.O. 53 GaO. 47 As/lnP quantum wells with varying barrier thicknesses using 10 ps Nd:Y AG excitation. For this excitation, holes and electrons are created in the Ino . 53 GaOA7 As layers. Due to momentum conservation the Nd:YAG excitation accelerates the electrons above the InP barrier where they can diffuse but cannot recombine. By examining the rise time of the quantum well emission, we can show that for samples with thick barriers, the harrier geometry largely controls the dynamic properties of the carriers after Nd:YAG excitation. [reprint (PDF)]
15.	High-Power Distributed-Feedback Quantum Cascade Lasers W.W. Bewley, I. Vurgaftman, C.S. Kim, J.R. Meyer, J. Nguyen, A.J. Evans, J.S. Yu, S.R. Darvish, S. Slivken and M. Razeghi SPIE Conference, San Jose, CA, Vol. 6127, pp. 612704-- January 23, 2006 ...[Visit Journal] Recently, a distributed-feedback quantum cascade laser operating in a single spectral mode at 4.8 µm and at temperatures up to 333 K has been reported. In the present work, we provide detailed measurements and modeling of its performance characteristics. The sidemode suppression ratio exceeds 25 dB, and the emission remains robustly single-mode at all currents and temperatures tested. Cw output powers of 99 mW at 298 K and 357 mW at 200 K are obtained at currents well below the thermal rollover point. [reprint (PDF)]
15.	Improved performance of IR photodetectors with 3D gap engineering J. Piotrowski and M. Razeghi Optoelectronic Integrated Circuit Materials, Physics and Devices, SPIE Conference, San Jose, CA; Proceedings, Vol. 2397-- February 6, 1995 ...[Visit Journal] The ultimate signal-to-noise performance of the semiconductor photodetector is limited by the statistical fluctuations of the thermal generation and recombination rates in photodetector material. Cooling is an effective but impractical way of suppression of the thermal processes. The performance of uncooled detectors can be improved by minimizing the thermal generation and recombination rates and reducing the actual volume of photodetector. This can be realized in 3D heterostructure devices. In these devices, the incident radiation is absorbed in small regions of narrow gap semiconductor, buried in wide gap volume and supplied with wide gap electric contacts and radiation concentrators. The practical near room-temperature 1 - 12 μm IR heterostructure photodetectors are reported. The devices are based on variable gap Hg_1-xCd_xTe. The 3D heterostructures have been obtained by Isothermal Vapor Growth Epitaxy in a reusable growth system which enables in situ doping during growth with foreign impurities. Ion milling was extensively used in preparation of the devices. Monolithic optical immersion has been applied for further improvement of performance. The 3D heterostructure devices exhibit performance exceeding that of conventional photodetectors. [reprint (PDF)]
15.	High power broad area quantum cascade lasers Y. Bai, S. Slivken, S.R. Darvish, A. Haddadi, B. Gokden and M. Razeghi Applied Physics Letters, Vol. 95, No. 22, p. 221104-1-- November 30, 2009 ...[Visit Journal] Broad area quantum cascade lasers (QCLs) are studied with ridge widths up to 400 µm, in room temperature pulsed mode operation at an emission wavelength around 4.45 µm. The peak output power scales linearly with the ridge width. A maximum total peak output power of 120 W is obtained from a single 400-µm-wide device with a cavity length of 3 mm. A stable far field emission characteristic is observed with dual lobes at ±38° for all tested devices, which suggests that these broad area QCLs are highly resistant to filamentation. [reprint (PDF)]
15.	Demonstration of mid-wavelength infrared nBn photodetectors based on type-II InAs/InAs_1-xSb_x superlattice grown by metal-organic chemical vapor deposition Donghai Wu, Arash Dehzangi, and Manijeh Razeghi Appl. Phys. Lett. 115, 061102-- August 6, 2019 ...[Visit Journal] We report design, growth, and characterization of midwavelength infrared nBn photodetectors based on a type-II InAs/InAs_1-xSb_x superlattice on a GaSb substrate grown by metal-organic chemical vapor deposition. An InAs/AlAs_1-ySb_y/InAs/InAs_1-xSb_x superlattice design was used as the large bandgap electron barrier in the photodetectors. At 150 K, the photodetector exhibits a peak responsivity of 1.23 A/W, corresponding to a quantum efficiency of 41% at an applied bias voltage of −100 mV under front-side illumination, with a 50% cut-off wavelength of 4.6 μm. With an R × A of 356 Ω·cm² and a dark current density of 1.6 × 10⁻⁴ A/cm² under an applied bias of −100 mV at 150 K, the photodetector exhibits a specific detectivity of 1.4 × 10¹¹ cm·Hz^1/2/W. [reprint (PDF)]
15.	Al_xGa_1-xN-based back-illuminated solar-blind photodetectors with external quantum efficiency of 89% E. Cicek, R. McClintock, C. Y. Cho, B. Rahnema, and M. Razeghi Appl. Phys. Lett. 103, 191108 (2013)-- November 5, 2013 ...[Visit Journal] We report on high performance Al_xGa_1−xN-based solar-blind ultraviolet photodetector (PD) array grown on sapphire substrate. First, high quality, crack-free AlN template layer is grown via metalorganic chemical vapor deposition. Then, we systematically optimized the device design and material doping through the growth and processing of multiple devices. After optimization, uniform and solar-blind operation is observed throughout the array; at the peak detection wavelength of 275 nm, 729 μm² area PD showed unbiased peak external quantum efficiency and responsivity of ∼80% and ∼176 mA/W, respectively, increasing to 89% under 5 V of reverse bias. Taking the reflection loses into consideration, the internal quantum efficiency of these optimized PD can be estimated to be as high as ∼98%. The visible rejection ratio measured to be more than six orders of magnitude. Electrical measurements yielded a low-dark current density: <2 × 10⁻⁹ A/cm², at 10 V of reverse bias. [reprint (PDF)]
15.	High-detectivity quantum-dot infrared photodetectors grown by metal-organic chemical-vapor deposition J. Szafraniec, S. Tsao, W. Zhang, H. Lim, M. Taguchi, A.A. Quivy, B. Movaghar and M. Razeghi Applied Physics Letters 88 (121102)-- March 20, 2006 ...[Visit Journal] A mid-wavelength infrared photodetector based on InGaAs quantum dots buried in an InGaP matrix and deposited on a GaAs substrate was demonstrated. Its photoresponse at T=77 K was measured to be around 4.7 μm with a cutoff at 5.5 μm. Due to the high peak responsivity of 1.2 A/W and low dark-current noise of the device, a specific peak detectivity of 1.1 x 10¹² cm·Hz^½·W⁻¹ was achieved at −0.9 V bias [reprint (PDF)]

Page 13 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)