Center for Quantum Devices - Most Downloaded Journal Articles

Page 12 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

15.	Extremely high electron mobility in a GaAs‐GaxIn1−xP heterostructure grown by metalorganic chemical vapor deposition M. Razeghi; M. Defour; F. Omnes; M. Dobers; J. P. Vieren; Y. Guldner Appl. Phys. Lett. 55, 457–459 (1989)-- June 17, 1989 ...[Visit Journal] On studying the magnetoresistivity of GaAs-GalnP heterostructures grown by low-pressure metalorganic chemical vapor deposition in magnetic fields up to 12 T and at liquid-helium temperatures, we have observed extremely high electron mobilities. Using the persistent photoconductivity effect, by illumination with red light, we reached a mobility of 780 000 cm2 / (V s) at an electron density of 4.1 X lOll cm- 2 . This high electron mobility is confirmed by cyclotron resonance measurements< [reprint (PDF)]
15.	High-performance short-wavelength infrared photodetectors based on type-II InAs/InAs1-xSbx/AlAs1-xSbx superlattices A. Haddadi, X.V. Suo, S. Adhikary, P. Dianat, R. Chevallier, A.M. Hoang, and M. Razeghi Applied Physics Letters 107 , 141104-- October 5, 2015 ...[Visit Journal] A high-performance short-wavelength infrared n-i-p photodiode based on InAs/InAs1-xSbx/AlAs1-xSbx type-II superlattices on GaSb substrate has been demonstrated. The device is designed to have a 50% cut-off wavelength of ~1.8μm at 300K. The photodetector exhibited a room-temperature (300 K) peak responsivity of 0.47 A/W at 1.6μm, corresponding to a quantum efficiency of 37% at zero bias under front-side illumination, without any anti-reflection coating. With an R×A of 285 Ω·cm² and a dark current density of 9.6×10^-5 A/cm² under −50mV applied bias at 300 K, the photodiode exhibited a specific detectivity of 6.45×10¹⁰ cm·Hz^½/W. At 200 K, the photodiode exhibited a dark current density of 1.3×10^-8 A/cm² and a quantum efficiency of 36%, resulting in a detectivity of 5.66×10¹² cm·Hz^½/W. [reprint (PDF)]
15.	Disorder of a Gax In1-xAsy P1-y-InP quantum well by Zn diffusion M. Razeghi, O. Acher, and F. Launay Semicond. Sci. Technol. 2 (1 987) 793-796.-- July 30, 1987 ...[Visit Journal] Data are presented showing for the first time that Zn diffusion into a Ga,In,-,As,P,-, - InP quantum well and superlattice (of 100 A thickness) completely disorders the quantum well and superlattice layers. The photoluminescence wavelength of the quantum well and the superlattice increased after Zn diffusion, which can be attributed to the In-Ga interdiffusion at the heterointerfaces, as a result of the interchange mechanism between the interstitials and substitutional zinc atoms [reprint (PDF)]
15.	Fabrication and characterization of novel hybrid green light emitting didoes based on substituting n-type ZnO for n-type GaN in an inverted p-n junction C. Bayram, D. Rogers, F. H. Teherani, and M. Razeghi Journal of Vacuum Science and Technology B, Vol. 27, No. 3, May/June, p. 1784-1788-- May 29, 2009 ...[Visit Journal] Details of the fabrication and characterization of hybrid green light emitting diodes, composed of n-ZnO/(InGaN/GaN) multi-quantum-wells/p-GaN on AlN/sapphire, are reported. Scanning electron microscope, atomic force microscopy, high resolution x-ray diffraction, and photoluminescence were used to study the hybrid device. The effects of solvents, annealing, and etching on n-ZnO are discussed. Successful hybridization of ZnO and (In)GaN into a green light emitting diode was realized. [reprint (PDF)]
15.	High operating temperature MWIR photon detectors based on Type-II InAs/GaSb superlattice M. Razeghi, B.M. Nguyen, P.Y. Delaunay, S. Abdollahi Pour, E.K.W. Huang, P. Manukar, S. Bogdanov, and G. Chen SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7608, p. 76081Q-1-- January 22, 2010 ...[Visit Journal] Recent efforts have been paid to elevate the operating temperature of Type-II InAs/GaSb superlattice Mid Infrared photon detectors. Optimized growth parameters and interface engineering technique enable high quality material with a quantum efficiency above 50%. Intensive study on device architecture and doping profile has resulted in almost one order of magnitude of improvement to the electrical performance and lifted up the 300 K-background BLIP operation temperature to 166 K. At 77 K, the ~4.2 µm cut-off devices exhibit a differential resistance area product in excess of the measurement system limit (10⁶ Ω·cm²) and a detectivity of 3x10¹³ cm·Hz^½·W⁻¹. High quality focal plane arrays were demonstrated with a noise equivalent temperature of 10 mK at 77 K. Uncooled camera is capable to capture hot objects such as soldering iron. [reprint (PDF)]
15.	Quantum Hall effect in In0.53Ga0.47As-InP heterojunctions with two populated electric subbands Y. Guldner, J. P. Vieren, and M. Voos F. Delahaye and D. Dominguez J. P. Hirtz and M. Razeghi Phys. Rev. B 33, 3990 1986-- March 15, 1986 ...[Visit Journal] Quantum-Hall-effect and Shubnikov–de Haas measurements are presented for InxGa1−xAs?(hyInP heterojunctions with two populated electric subbands and low electron density (𝑛𝑠≤5×1011 cm−2). The Shubnikov–de Haas oscillations clearly show two different periodicities. An anomalous behavior of the quantum Hall effect is observed, in particular some plateaus are missing and other plateaus are enhanced. Precise measurements of the Hall resistance have been performed and it is shown that the resistance of the i=2 plateau is equal to its theoretical value h/2𝑒2 with an uncertainty of ∼10−8. [reprint (PDF)]
15.	High-performance bias-selectable dual-band Short-/Mid-wavelength infrared photodetectors and focal plane arrays based on InAs/GaSb/AlSb Type-II superlattices M. Razeghi; A.M. Hoang; A. Haddadi; G. Chen; S. Ramezani-Darvish; P. Bijjam; P. Wijewarnasuriy; E. Decuir Proc. SPIE 8704, Infrared Technology and Applications XXXIX, 87041W (June 18, 2013)-- June 18, 2013 ...[Visit Journal] We report a bias selectable dual-band Type-II superlattice-based short-wave infrared (SWIR) and mid-wave infrared (MWIR) co-located photodetector capable of active and passive imaging. A new double-layer etch-stop scheme is introduced for back-side-illuminated photodetectors, which enhanced the external quantum efficiency both in the SWIR and MWIR spectral regions. Temperature-dependent dark current measurements of pixel-sized 27 μm detectors found the dark current density to be ∼1×10-5 A/cm2 for the ∼4.2 μm cut-off MWIR channel at 140 K. This corresponded to a reasonable imager noise equivalent difference in temperature of ∼49 mK using F/2.3 optics and a 10 ms integration time (tint), which lowered to ∼13 mK at 110 K using and integration time of 30 ms, illustrating the potential for high-temperature operation. The SWIR channel was found to be limited by readout noise below 150 K. An excellent imagery from the dual-band imager exemplifying pixel coincidence is shown. [reprint (PDF)]
15.	Research activity on Type-II InAs/GaSb superlattice for LWIR detection and imaging at the Center for Quantum Devices M. Razeghi and B.M. Nguyen American Institute of Physics Conference Proceedings Vol. 949, Issue 1, p. 35-42, 6th International Workshop on Information Optics (WIO'07), Reykjavik, Iceland, June 25-30, 2007-- October 24, 2007 ...[Visit Journal] Type-II superlattice photodetectors have recently experienced significant improvements in both theoretical structure design and experimental realization. Empirical Tight Binding Method was initiated and developed for Type-II superlattice. A new Type-II structure, called M-structure, was introduced and theoretically demonstrated high R₀A, high quantum efficiency. Device design and growth condition were optimized to improve the performance. As a result, a 54% quantum efficiency, a 12 Ω·cm² R₀A were achieved for 11 µm cut-off photodetector at 77 K. Effective surface passivation techniques for MWIR and LWIR Type-II superlattice were developed. FPA imaging at MWIR and LWIR were demonstrated with a capability of imaging up to room temperature and 211 K respectively. The noise equivalent temperature difference presented a peak at 50 mK for MWIR FPA at 121 K and 26 mK for LWIR FPA at 81 K. [reprint (PDF)]
15.	III-Nitride Optoelectronic Devices: From ultraviolet detectors and visible emitters towards terahertz intersubband devices M. Razeghi, C. Bayram, Z. Vashaei, E. Cicek and R. McClintock IEEE Photonics Society 23rd Annual Meeting, November 7-10, 2010, Denver, CO, Proceedings, p. 351-352-- January 20, 2011 ...[Visit Journal] III-nitride optoelectronic devices are discussed. Ultraviolet detectors and visible emitters towards terahertz intersubband devices are reported. Demonstration of single photon detection efficiencies of 33% in the ultraviolet regime, intersubband energy level as low as in the mid-infrared regime, and GaN-based resonant tunneling diodes with negative resistance of 67 Ω are demonstrated. [reprint (PDF)]
15.	Passivation of type-II InAs/GaSb double heterostructure P.Y. Delaunay, A. Hood, B.M. Nguyen, D. Hoffman, Y. Wei, and M. Razeghi Applied Physics Letters, Vol. 91, No. 9, p. 091112-1-- August 27, 2007 ...[Visit Journal] Focal plane array fabrication requires a well passivated material that is resistant to aggressive processes. The authors report on the ability of type-II InAs/GaSb superlattice heterodiodes to be more resilient than homojunctions diodes in improving sidewall resistivity through the use of various passivation techniques. The heterostructure consisting of two wide band gap (5 µm) superlattice contacts and a low band gap active region (11 µm) exhibits an R₀A averaging of 13·Ω cm². The devices passivated with SiO₂, Na₂S and SiO₂ or polyimide did not degrade compared to the unpassivated sample and the resistivity of the sidewalls increased to 47 kΩ·cm. [reprint (PDF)]
15.	Room temperature continuous wave operation of quantum cascade lasers with 12.5% wall plug efficiency Y. Bai, S. Slivken, S.R. Darvish, and M. Razeghi Applied Physics Letters, Vol. 93, No. 2, p. 021103-1-- July 14, 2008 ...[Visit Journal] An InP based quantum cascade laser heterostructure emitting at 4.6 µm was grown with gas-source molecular beam epitaxy. The wafer was processed into a conventional double-channel ridge waveguide geometry with ridge widths of 19.7 and 10.6 µm without semi-insulating InP regrowth. An uncoated, narrow ridge device with a 4.8 mm cavity length was epilayer down bonded to a diamond submount and exhibits 2.5 W maximum output power with a wall plug efficiency of 12.5% at room temperature in continuous wave operation. [reprint (PDF)]
15.	Superlattice sees colder objects in two colors and high resolution M. Razeghi SPIE Newsroom-- February 10, 2012 ...[Visit Journal] A special class of semiconductor material can now detect two wavebands of light with energies less than a tenth of an electron volt in high resolution using the same IR camera. [reprint (PDF)]
15.	Multiple-band, Single-mode, High-power, Phase-locked, Mid-infrared Quantum Cascade Laser Arrays Manijeh Razeghi, Wenjia Zhou, Quanyong Lu, Donghai Wu, and Steven Slivken Imaging and Applied Optics 2018, JTh1A.2-- September 15, 2018 ...[Visit Journal] Single-mode, 16-channel, phase-locked laser arrays based on quantum cascade laser technology are demonstrated at multiple spectral bands across the mid-infrared spectrum region. High peak output power of 50W is achieved around the long-wavelength band of 7.7µm, while a side mode suppression ratio over 25dB is obtained. Far field distribution measurement result indicates a uniform phase distribution across the array output. [reprint (PDF)]
15.	Temperature insensitivity of the Al-free InGaAsP/GaAs lasers for λ = 808 and 908 nm M. Razeghi, H. Yi, J. Diaz, S. Kim, and M. Erdtmann SPIE Conference, San Jose, CA; Proceedings 3001-- February 12, 1997 ...[Visit Journal] n this work, we present our recent achievements for the reliability of the Al-free lasers at high temperatures and high powers. Laser operations up to 30,000 hours were achieved without any degradation in the lasers characteristics from 7 randomly selected InGaAsP/GaAs diodes for λ = 808 nm. The test were performed for lasers without mirror-coating for optical power of 0.5 to 1 W CW at 50 approximately 60 °C. To the best of our knowledge, this is the first direct demonstration of the extremely high reliability of Al-free diodes operations at high powers and temperatures for periods of time much longer than practical need (approximately 3 years). The characteristics during the tests are discussed in detail. [reprint (PDF)]
15.	Ammonium Sulfide Passivation of Type-II InAs/GaSb Superlattice Photodiodes A. Gin, Y. Wei, A. Hood, A. Bajowala, V. Yazdanpanah, M. Razeghi and M.Z. Tidrow Applied Physics Letters, 84 (12)-- March 22, 2004 ...[Visit Journal] We report on the surface passivation of Type-II InAs/GaSb superlattice photodetectors using various ammonium sulfide solutions. Compared to unpassivated detectors, zero-bias resistance of treated 400 µm×400 µm devices with 8 µm cutoff wavelength was improved by over an order of magnitude to ~20 kΩ at 80 K. Reverse-bias dark current density was reduced by approximately two orders of magnitude to less than 10 mA/cm² at –2 V. Dark current modeling, which takes into account trap-assisted tunneling, indicates greater than 70 times reduction in bulk trap density for passivated detectors. [reprint (PDF)]
15.	Toward realization of small-size dual-band long-wavelength infrared photodetectors based on InAs/GaSb/AlSb type-II superlattices Romain Chevallier, Abbas Haddadi, Manijeh Razeghi Solid-State Electronics 136, pp. 51-54-- June 20, 2017 ...[Visit Journal] In this study, we demonstrate 12 × 12 µm² high-performance, dual-band, long-wavelength infrared (LWIR) photodetectors based on InAs/GaSb/AlSb type-II superlattices. The structure consists of two back-to-back heterojunction photodiodes with 2 µm-thick p-doped absorption regions. High quality dry etching combined with SiO₂ passivation results in a surface resistivity value of 7.9 × 10⁵ Ω·cm for the longer (red) channel and little degradation of the electrical performance. The device reaches dark current density values of 4.5 × 10⁻⁴ A/cm² for the longer (red) and 1.3 × 10⁻⁴ A/cm² for the shorter (blue) LWIR channels at quantum efficiency saturation. It has 50% cut-off wavelengths of 8.3 and 11.2 µm for the blue and red channel, respectively, at 77 K in back-side illumination configuration and exhibits quantum efficiencies of 37% and 29%, respectively. This results in specific detectivity values of 2.5 × 10¹¹ cm·Hz^½/W and 1.3 × 10¹¹ cm·Hz^½/W at 77 K. [reprint (PDF)]
15.	Modeling the electronic band-structure of strained long-wavelength Type-II superlattices using the scattering matrix method Abbas Haddadi，Gail Brown，Manijeh Razeghi J Infrared Millim W 44 (3), 346 (2025) ...[Visit Journal] This study introduces a comprehensive theoretical framework for accurately calculating the electronic band-structure of strained long-wavelength InAs/GaSb type-II superlattices. Utilizing an eight-band k ⋅ p Hamilto⁃ nian in conjunction with a scattering matrix method， the model effectively incorporates quantum confinement， strain effects， and interface states. This robust and numerically stable approach achieves exceptional agreement with experimental data， offering a reliable tool for analyzing and engineering the band structure of complex multi⁃ layer systems [reprint (PDF)]
15.	Type-II superlattice-based extended short-wavelength infrared focal plane array with an AlAsSb/GaSb superlattice etch-stop layer to allow near-visible light detection Romain Chevallier, Arash Dehzangi, Abbas Haddadi, and Manijeh Razeghi Optics Letters Vol. 42, Iss. 21, pp. 4299-4302-- October 17, 2017 ...[Visit Journal] A versatile infrared imager capable of imaging the near-visible to the extended short-wavelength infrared (e-SWIR) is demonstrated using e-SWIR InAs/GaSb/AlSb type-II superlattice-based photodiodes. A bi-layer etch-stop scheme consisting of bulk InAs_0.91Sb_0.09 and AlAs_0.1Sb_0.9/GaSb superlattice layers is introduced for substrate removal from the hybridized back-side illuminated photodetectors. The implementation of this new technique on an e-SWIR focal plane array results in a significant enhancement in the external quantum efficiency (QE) in the 1.8–0.8μm spectral region, while maintaining a high QE at wavelengths longer than 1.8μm. Test pixels exhibit 100% cutoff wavelengths of ∼2.1 and ∼2.25μm at 150 and 300K, respectively. They achieve saturated QE values of 56% and 68% at 150 and 300K, respectively, under back-side illumination and without any anti-reflection coating. At 150K, the photodetectors (27μm×27μm area) exhibit a dark current density of 4.7×10⁻⁷ A/cm² under a −50 mV applied bias providing a specific detectivity of 1.77×10¹² cm·Hz^1/2/W. At 300K, the dark current density reaches 6.6×10⁻² A/cm² under −50 mV bias, providing a specific detectivity of 5.17×10⁹ cm·Hz^1/2/W. [reprint (PDF)]
15.	Avalanche Photodetector Based on InAs/InSb Superlattice Arash Dehzangi, Jiakai Li, Lakshay Gautam and Manijeh Razeghi Quantum rep. 2020, 2(4), 591-599; https://doi.org/10.3390/quantum2040041 (registering DOI)-- December 4, 2020 ...[Visit Journal] This work demonstrates a mid-wavelength infrared InAs/InSb superlattice avalanche photodiode (APD). The superlattice APD structure was grown by molecular beam epitaxy on GaSb substrate. The device exhibits a 100 % cut-off wavelength of 4.6 µm at 150 K and 4.30 µm at 77 K. At 150 and 77 K, the device responsivity reaches peak values of 2.49 and 2.32 A/W at 3.75 µm under −1.0 V applied bias, respectively. The device reveals an electron dominated avalanching mechanism with a gain value of 6 at 150 K and 7.4 at 77 K which was observed under −6.5 V bias voltage. The gain value was measured at different temperatures and different diode sizes. The electron and hole impact ionization coefficients were calculated and compared to give a better prospect of the performance of the device. [reprint (PDF)]
15.	Cubic Phase GaN on Nano-grooved Si (100) via Maskless Selective Area Epitaxy Bayram, C., Ott, J. A., Shiu, K.-T., Cheng, C.-W., Zhu, Y., Kim, J., Razeghi, M. and Sadana, D. K. Adv. Funct. Mater. 2014-- April 1, 2014 ...[Visit Journal] A method of forming cubic phase (zinc blende) GaN (referred as c-GaN) on a CMOS-compatible on-axis Si (100) substrate is reported. Conventional GaN materials are hexagonal phase (wurtzite) (referred as h-GaN) and possess very high polarization fields (∼MV/cm) along the common growth direction of <0001>. Such large polarization fields lead to undesired shifts (e.g., wavelength and current) in the performance of photonic and vertical transport electronic devices. The cubic phase of GaN materials is polarization-free along the common growth direction of <001>, however, this phase is thermodynamically unstable, requiring low-temperature deposition conditions and unconventional substrates (e.g., GaAs). Here, novel nano-groove patterning and maskless selective area epitaxy processes are employed to integrate thermodynamically stable, stress-free, and low-defectivity c-GaN on CMOS-compatible on-axis Si. These results suggest that epitaxial growth conditions and nano-groove pattern parameters are critical to obtain such high quality c-GaN. InGaN/GaN multi-quantum-well structures grown on c-GaN/Si (100) show strong room temperature luminescence in the visible spectrum, promising visible emitter applications for this technology. [reprint (PDF)]
15.	Persistent photoconductivity in thin undoped GaInP/GaAs quantum wells S. Elhamri, M. Ahoujja, K. Ravindran, D.B. Mast, R.S. Newrock, W.C. Mitchel, G.J. Brown, I. Lo, M. Razeghi and X. He Applied Physics Letters 66 (2)-- January 9, 1995 ...[Visit Journal] Persistent photoconductivity has been observed at low temperatures in thin, unintentionally doped GaInP/GaAs/GaInP quantum wells. The two‐dimensional electron gas was studied by low field Hall and Shubnikov–de Haas effects. After illumination with red light, the electron concentration increased from low 10¹¹ cm⁻² to more than 7×10¹¹ cm⁻² resulting in an enhancement of both the carrier mobility and the quantum lifetime. The persistent photocarriers cannot be produced by DX-like defects since the shallow dopant concentration in the GaInP layers is too low to produce the observed concentration. We suggest that the persistent carriers are produced by photoionization of deep intrinsic donors in the GaInP barrier layer. We also report observation of a parallel conduction path in GaInP induced by extended illumination. [reprint (PDF)]
15.	GaN, GaAlN, and AlN for use in UV Detectors for Astrophysics: An Update P. Kung, A. Saxler, X. Zhang, D. Walker, M. Razeghi, and M. Ulmer SPIE Photonics West '96 Photodetectors: Materials and Devices; Proceedings 2685-- January 27, 1996 ...[Visit Journal] In SPIE Proceeding 2397 we demonstrated that there is a large payoff still to be gained by further improvements in the performance of solar blind UV detectors for astronomical purposes. We suggested that a particularly promising future technology is one based on the ability of investigators to produce high-quality films made of wide bandgap III-IV semiconductors. Here we report on significant progress we have made over the past year to fabricate and test single-pixel devices. The next step will be to measure and improve detective efficiency, measure the solar blindness over a larger dynamic range, and begin developing multiple-pixel designs. [reprint (PDF)]
15.	Back-illuminated solar-blind photodetectors for imaging applications R. McClintock, A. Yasan, K. Mayes, P. Kung, and M. Razeghi SPIE Conference, Jose, CA, Vol. 5732, pp.175-- January 22, 2005 ...[Visit Journal] Back-illuminated solar-blind ultraviolet p-i-n photodetectors and focal plane arrays are investigated. We initially study single-pixel devices and then discuss the hybridization to a read-out integrated circuit to form focal plane arrays for solar-blind UV imaging. [reprint (PDF)]
15.	On the Description of the Collision Terms in Three-Valley Hydrodynamic Models for GaAs Device Modeling C. Besikci and M. Razeghi IEEE Transactions on Electron Devices 41 (8)-- August 1, 1994 ...[Visit Journal] A reduced set of transport parameters is proposed for the collision terms of the three-valley hydrodynamic model which is a faster alternative to ensemble Monte Carlo simulations. The predictions of the proposed model have been found to be in excellent agreement with transient ensemble Monte Carlo data. The reduction in the number of the transport parameters makes the model relatively easy to implement with substantial accuracy. The transport parameters which are of interest in semiclassical device modeling are presented as a function of electron energy. [reprint (PDF)]
15.	Photovoltaic effects in GaN structures with p-n junction X. Zhang, P. Kung, D. Walker, J. Piotrowski, A. Rogalski, A. Saxler, and M. Razeghi Applied Physics Letters 67 (14)-- October 2, 1995 ...[Visit Journal] Large-area GaN photovoltaic structures with p-n junctions have been fabricated using atmospheric pressure metalorganic chemical vapor deposition. The photovoltaic devices typically exhibit selective spectral characteristics with two narrow peaks of opposite polarity. This can be related to p-n junction connected back‐to‐back with a Schottky barrier. The shape of the spectral characteristic is dependent on the thickness of the n- and p-type regions. The diffusion length of holes in the n-type GaN region, estimated by theoretical modeling of the spectral response shape, was about 0.1 μm. [reprint (PDF)]

Page 12 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)