Center for Quantum Devices - Most Downloaded Journal Articles

Page 11 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

16.	TEG IN LP-MO CVD Ga 0 4 7 ln 0 S3 As-lnP SUPERLATTICE M. RAZEGHIM. A. POISSONJ. P. LARIVAINB. de CREMOUXJ. P. DUCHEMIN ELECTRONICS LETTERs, 1982 ,Vol. 18-- April 15, 1982 ...[Visit Journal] We report the first successful growth of Ga o .4. 7 In 0 . J3 As-InPsuperlattice by the low-pressure metalorganic chemicalvapour deposition technique, and evidence for TEG proper-ties in these structures. [reprint (PDF)]
16.	Recent performance records for mid-IR quantum cascade lasers M. Razeghi; Y. Bai; S. Slivken; S. Kuboya; S.R. Darvish Terahertz and Mid Infrared Radiation: Basic Research and Practical Applications, 2009. TERA-MIR International Workshop [5379656], (2009) -- November 9, 2009 ...[Visit Journal] The wall plug efficiency of the mid-infrared quantum cascade laser in room temperature continuous wave operation is brought to 17%. Peak output power from a broad area (400 μm x 3 mm) device gives 120 W output power in pulsed mode operation at room temperature. Using a single-well-injector design, specifically made for low temperature operation, a record wall plug efficiency of 53% is demonstrated at 40 K. [reprint (PDF)]
15.	Sb-based infrared materials and photodetectors for the 3-5 and 8-12 μm range E. Michel, J.D. Kim, S. Park, J. Xu, I. Ferguson, and M. Razeghi SPIE Photonics West '96 'Photodetectors: Materials and Devices'; Proceedings 2685-- January 27, 1996 ...[Visit Journal] In this paper, we report on the growth of InSb on (100) Si and (111)B GaAs substrates and the growth of InAsSb alloys for longer wavelength applications. The fabrication and characterization of photodetectors based on these materials are also reported. Both photoconductive and photovoltaic devices are investigated. The photodiodes are InSb p-i-n structures and InSb/InAs_1-xSb_x/InSb double heterostructures grown on (100) and (111)B semi-insulating GaAs and Si substrates by low pressure metalorganic chemical vapor deposition and solid source molecular beam epitaxy. The material parameters for device structures have been optimized through theoretical calculations based on fundamental mechanisms. InSb p-i-n photodiodes with peak responsivities approximately 103 V/W were grown on Si and (111) GaAs substrates. An InAsSb photovoltaic detector with a composition of x equals 0.85 showed photoresponse up to 13 micrometers at 300 K with a peak responsivity of 9.13 X 10^-2 V/W at 8 micrometers . The R₀A product of InAsSb detectors has been theoretically and experimentally analyzed. [reprint (PDF)]
15.	Investigation of Enhanced Heteroepitaxy and Electrical Properties in k-Ga2O3 due to Interfacing with β-Ga2O3 Template Layers Junhee Lee, Lakshay Gautam, Ferechteh H. Teherani, Eric V. Sandana, P. Bove, David J. Rogers and Manijeh Razeghi J. Lee, M. Razeghi, Physica Status Solidi A 2023,220, 2200559, https://doi.org/10.1002/pssa.202200559 ...[Visit Journal] Heteroepitaxial k-Ga2O3 films grown by metal-organic chemical vapor deposition (MOCVD) were found to have superior materials and electrical properties thanks to the interfacing with a b-Ga2O3 template layer. k-Ga2O3grown on sapphire has not been able to demonstrate its full potential due to materials imperfections created by strain induced by the lattice mismatch at the interface between the epilayer and the substrate. By adopting a b-Ga2O3 template on a c-sapphire substrate, higher quality k-Ga2O3thin films were obtained, as evidenced by a smoother surface morphology, narrower XRD peaks, and superior electrical performance. The implications of this phenomenon, caused by b-Ga2O3 buffer layer, are already very encouraging for both boosting current device performance and opening up the perspective of novel applications for Ga2O3. [reprint (PDF)]
15.	Minority electron unipolar photodetectors based on Type-II InAs/GaSb/AlSb superlattices for very long wavelength infrared detection B.M. Nguyen, S. Abdollahi Pour, S. Bogdanov and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-28, 2010), Vol. 7608, p. 760825-1-- January 22, 2010 ...[Visit Journal] The bandstructure tunability of Type-II antimonide-based superlattices has been significantly enhanced since the introduction of the M-structure superlattice, resulting in significant improvements of Type-II superlattice infrared detectors. By using M-structure, we developed the pMp design, a novel infrared photodetector architecture that inherits the advantages of traditional photoconductive and photovoltaic devices. This minority electron unipolar device consists of an M-structure barrier layer blocking the transport of majority holes in a p-type semiconductor, resulting in an electrical transport due to minority carriers with low current density. Applied for the very long wavelength detection, at 77K, a 14µm cutoff detector exhibits a dark current 3.3 mA·cm⁻², a photoresponsivity of 1.4 A/W at 50mV bias and the associated shot-noise detectivity of 4x10¹⁰ Jones. [reprint (PDF)]
15.	Imprinting of Nanoporosity in Lithium-Doped Nickel Oxide through the use of Sacrificial Zinc Oxide Nanotemplates Vinod E. Sandana, David J. Rogers, Ferechteh H. Teheran1, Philippe Bove, Ryan McClintock and Manijeh Razeghi Proc. SPIE 10105, Oxide-based Materials and Devices VIII, 101052C-- April 3, 2017 ...[Visit Journal] Methods for simultaneously increasing the conductivity and the porosity of NiO layers grown by pulsed laser deposition (PLD) were investigated in order to develop improved photocathodes for p-DSSC applications. NiO:Li (20at%) layers grown on c-Al₂O₃ by PLD showed a sharp drop in conductivity with increasing substrate temperature. Layers grown at room temperature were more than two orders of magnitude more conductive than undoped NiO layers but did not show evidence of any porosity in Scanning Electron Microscope (SEM) images. A new method for imposing a nanoporosity in NiO was developed based on a sacrificial template of nanostructured ZnO. SEM images and EDX spectroscopy showed that a nanoporous morphology had been imprinted in the NiO overlayer after preferential chemical etching away of the nanostructured ZnO underlayer. Beyond p-DSSC applications, this new process could represent a new paradigm for imprinting porosity in a whole range of materials. [reprint (PDF)]
15.	Aluminum gallium nitride short-period superlattices doped with magnesium A. Saxler, W.C. Mitchel, P. Kung and M. Razeghi Applied Physics Letters 74 (14)-- April 9, 1999 ...[Visit Journal] Short-period superlattices consisting of alternating layers of GaN:Mg and AlGaN:Mg were grown by low-pressure organometallic vapor phase epitaxy. The electrical properties of these superlattices were measured as a function of temperature and compared to conventional AlGaN:Mg layers. It is shown that the optical absorption edge can be shifted to shorter wavelengths while lowering the acceptor ionization energy by using short-period superlattice structures instead of bulk-like AlGaN:Mg. [reprint (PDF)]
15.	Techniques for High-Quality SiO₂ Films J. Nguyen and M. Razeghi SPIE Conference, January 25-29, 2007, San Jose, CA Proceedings – Quantum Sensing and Nanophotonic Devices IV, Vol. 6479, p. 64791K-1-8-- January 29, 2007 ...[Visit Journal] We report on the comparison of optical, structural, and electrical properties of SiO₂ using plasma-enhanced chemical vapor deposition and ion-beam sputtering deposition. High-quality, low-temperature deposition of SiO₂ by ion-beam sputtering deposition is shown to have lower absorption, smoother and more densely packed films, a lower amount of fixed oxide charges, and a lower trapped-interface density than SiO₂ by plasma-enhanced chemical vapor deposition. This high-quality SiO₂ is then demonstrated as an excellent electrical and mechanical surface passivation layer on Type-II InAs/GaSb photodetectors [reprint (PDF)]
15.	High Performance Quantum Cascade Lasers Grown by Gas-Source Molecular Beam Epitaxy M. Razeghi, S. Slivken, A. Tahraoui and A. Matlis SPIE Conference, San Jose, CA, -- January 22, 2001 ...[Visit Journal] Recent improvements in quantum cascade laser technology have led to a number of very impressive results. This paper is a brief summary of the technological development and state-of- the-art performance of quantum cascade lasers produced at the Center for Quantum Devices. Laser design will be discussed, as well as experimental details of device fabrication. Room temperature QCL operation has been reported for lasers emitting between 5 - 11 μm, with 9 - 11 μm lasers operating up to 425 K. We also demonstrate record room temperature peak output powers at 9 and 11 μm(2.5 W and 1 W respectively) as well as record low 80 K threshold current densities (250 A/cm²) for some laser designs. Finally, some of the current limitations to laser efficiency are mentioned, as well as a means to combat them. [reprint (PDF)]
15.	Beryllium compensation doping of InAs/GaSb infrared superlattice photodiodes D. Hoffman, B.M. Nguyen, P.Y. Delaunay, A. Hood, M. Razeghi and J. Pellegrino Applied Physics Letters, Vol. 91, No. 14, p. 143507-1-- October 1, 2007 ...[Visit Journal] Capacitance-voltage measurements in conjunction with dark current measurements on InAs/GaSb long wavelength infrared superlattice photodiodes grown by molecular-beam epitaxy on GaSb substrates are reported. By varying the beryllium concentration in the InAs layer of the active region, the residually n-type superlattice is compensated to become slightly p-type. By adjusting the doping, the dominant dark current mechanism can be varied from diffusion to Zener tunneling. Minimization of the dark current leads to an increase of the zero-bias differential resistance from less than 4 to 32 cm² for a 100% cutoff of 12.05 µm [reprint (PDF)]
15.	Recent advances in high power mid- and far-wavelength infrared lasers for free space communication S. Slivken and M. Razeghi SPIE Optics East Conference, October 1-4, 2006, Boston, MA Proceedings – Active and Passive Optical Components for Communications VI, Vol. 6389, p. 63890S-1-- October 4, 2006 ...[Visit Journal] Link reliability is a significant issue for free space optical links. Inclement weather, such as fog, can seriously reduce the transmission of light through the atmosphere. However, this effect, for some types of fog, is wavelength-dependent. In order to improve link availability in both metro and hostile environments, mid- and far-wavelength infrared diode lasers can be of use. This paper will discuss some of the recent advances in high-power, uncooled quantum cascade lasers and their potential for use in long range and/or highly reliable free space communication links. [reprint (PDF)]
15.	p-doped GaAs/Ga_0.51In_0.49P quantum well intersub-band photodetectors J. Hoff, X. He, M. Erdtmann, E. Bigan, M. Razeghi, and G.J. Brown Journal of Applied Physics 78 (3)-- August 1, 1995 ...[Visit Journal] Lattice‐matched p-doped GaAs–Ga_0.51In_0.49P quantum well intersub‐band photodetectors with three different well widths have been grown on GaAs substrates by metal‐organic chemical‐vapor deposition and fabricated into mesa structures. The photoresponse cutoff wavelength varies between 3.5 and 5.5 μm by decreasing the well width from 50 down to 25 Å. Dark current measurements as a function of temperature reveal activation energies for thermionic emission that closely correspond to measured cutoff wavelengths. Experimental results are in reasonable agreement with Kronig–Penney calculations. [reprint (PDF)]
15.	High power continuous operation of a widely tunable quantum cascade laser with an integrated amplifier S. Slivken, S. Sengupta, and M. Razeghi Applied Physics Letters 107, 251101-- December 21, 2015 ...[Visit Journal] Wide electrical tuning and high continuous output power is demonstrated from a single mode quantum cascade laser emitting at a wavelength near 4.8 μm. This is achieved in a space efficient manner by integrating an asymmetric sampled grating distributed feedback tunable laser with an optical amplifier. An initial demonstration of high peak power operation in pulsed mode is demonstrated first, with >5 W output over a 270 nm (113 cm⁻¹) spectral range. Refinement of the geometry leads to continuous operation with a single mode spectral coverage of 300 nm (120 cm⁻¹) and a maximum continuous power of 1.25 W. The output beam is shown to be nearly diffraction-limited, even at high amplifier current. [reprint (PDF)]
15.	Materials characterization of n-ZnO/p-GaN:Mg/c-Al(2)O(3) UV LEDs grown by pulsed laser deposition and metal-organic chemical vapor deposition D. Rogers, F.H. Teherani, P. Kung, K. Minder, and M. Razeghi Superlattices and Microstructures-- April 1, 2007 ...[Visit Journal] n-ZnO/p-GaN:Mg hybrid heterojunctions grown on c-Al₂O₃ substrates showed 375 nm room temperature electroluminescence. It was suggested that the high materials and interface quality obtained using pulsed laser deposition for the n-ZnO growth and metal–organic chemical vapor deposition for the p-GaN:Mg were key factors enabling the injection of holes and the radiative near band edge recombination in the ZnO. In this paper we present the materials characterization of this structure using x-ray diffraction, scanning electron microscopy and atomic force microscopy. [reprint (PDF)]
15.	InTlSb alloys for infrared detection E. Bigan, Y.H. Choi, G. Labeyrie, and M. Razeghi Proceedings, SPIE Nonlinear Optics for High-Speed Electronics and Optical Frequency Conversion, Vol. 2145-- January 24, 1994 ...[Visit Journal] InTISb alloys have been grown by low-pressure metalorganic chemical vapor deposition, and characterized. Photoconductors exhibit a cutoff wavelength that can be tailored from 5.5 μm up to 9 μm by varying the thallium content. Experimental observations suggest that this can be further extended by increasing the thallium content. An InTISb photoconductor having a 9 μm cutoff wavelength exhibited a D* of 10⁹ cm·Hz^½·W^-1 at 7 μm operating wavelength. [reprint (PDF)]
15.	Combined resonant tunneling and rate equation modeling of terahertz quantum cascade lasers Zhichao Chen , Andong Liu, Dong Chang , Sukhdeep Dhillon , Manijeh Razeghi , Feihu Wang Journal of Applied Physics, 135, 115703 ...[Visit Journal] Terahertz (THz) quantum cascade lasers (QCLs) are technologically important laser sources for the THz range but are complex to model. An efficient extended rate equation model is developed here by incorporating the resonant tunneling mechanism from the density matrix formalism, which permits to simulate THz QCLs with thick carrier injection barriers within the semi-classical formalism. A self-consistent solution is obtained by iteratively solving the Schrödinger-Poisson equation with this transport model. Carrier-light coupling is also included to simulate the current behavior arising from stimulated emission. As a quasi-ab initio model, intermediate parameters such as pure dephasing time and optical linewidth are dynamically calculated in the convergence process, and the only fitting parameters are the interface roughness correlation length and height. Good agreement has been achieved by comparing the simulation results of various designs with experiments, and other models such as density matrix Monte Carlo and non-equilibrium Green’s function method that, unlike here, require important computational resources. The accuracy, compatibility, and computational efficiency of our model enables many application scenarios, such as design optimization and quantitative insights into THz QCLs. Finally, the source code of the model is also provided in the supplementary material of this article for readers to repeat the results presented here, investigate and optimize new designs. [reprint (PDF)]
15.	High Carrier Lifetime InSb Grown on GaAs Substrates E. Michel, H. Mohseni, J.D. Kim, J. Wojkowski, J. Sandven, J. Xu, M. Razeghi, R. Bredthauer, P. Vu, W. Mitchel, and M. Ahoujja Applied Physics Letters 71 (8-- August 25, 1997 ...[Visit Journal] We report on the growth of near bulklike InSb on GaAs substrates by molecular beam epitaxy despite the 14% lattice mismatch between the epilayer and the substrate. Structural, electrical, and optical properties were measured to assess material quality. X-ray full widths at half-maximum were as low as 55 arcsec for a 10 µm epilayer, peak mobilities as high as ~ 125 000 cm2/V s, and carrier lifetimes up to 240 ns at 80 K. [reprint (PDF)]
15.	InAsSbP/InAsSb/InAs Diode Lasers Emitting at 3.2 μm Grown by Metalorganic Chemical Vapor Deposition D. Wu, E. Kaas, J. Diaz, B. Lane, A. Rybaltowski, H.J. Yi, and M. Razeghi IEEE Photonics Technology Letters 9 (2)-- February 1, 1997 ...[Visit Journal] InAsSb-InAsSbP double heterostructure diode lasers have been grown by metal-organic chemical vapor deposition on (100) InAs substrates. High-output powers of 660 mW in pulse mode and 300 mW in continuous wave operation with 400-μm cavity length and 100-μm-wide aperture at 78 K have been obtained. These devices showed low threshold current density of 40 A/cm2, low internal loss of 3.0 cm/sup -1/, far-field /spl theta//sub /spl perp// of 34/spl deg/ with differential efficiency of 90% at 78 K, and high operating temperatures of 220 K. [reprint (PDF)]
15.	Watt level performance of quantum cascade lasers in room temperature continuous wave operation at λ ∼ 3.76 μm N. Bandyopadhyay, Y. Bai, B. Gokden, A. Myzaferi, S. Tsao, S. Slivken and M. Razeghi Applied Physics Letters, Vol. 97, No. 13-- September 27, 2010 ...[Visit Journal] An InP-based quantum cascade laser heterostructure emitting at 3.76 μm is grown with gas-source molecular beam epitaxy. The laser core is composed of strain balanced In_0.76Ga_0.24As/In_0.26Al_0.74As. Pulsed testing at room temperature exhibits a low threshold current density (1.5 kA/cm²) and high wall plug efficiency (10%). Room temperature continuous wave operation gives 6% wall plug efficiency with a maximum output power of 1.1 W. Continuous wave operation persists up to 95 °C. [reprint (PDF)]
15.	Effects of substrate quality and orientation on the characteristics of III-nitride resonant tunneling diodes Z. Vashaei, C. Bayram, R. McClintock and M. Razeghi SPIE Proceedings, San Francisco, CA (January 22-27, 2011), Vol 7945, p. 79451A-- January 23, 2011 ...[Visit Journal] Al(Ga)N/GaN resonant tunneling diodes (RTDs) are grown by metal-organic chemical vapor deposition. The effects of material quality on room temperature negative differential resistance (NDR) behaviour of RTDs are investigated by growing the RTD structure on AlN, GaN, and lateral epitaxial overgrowth GaN templates. This reveals that NDR characteristics of RTDs are very sensitive to material quality (such as surface roughness and dislocations density). The effects of the aluminum content of AlGaN double barriers (DB) and polarization fields on NDR characteristic of AlGaN/GaN RTDs were also investigated by employing low dislocation density c-plane (polar) and m-plane (nonpolar) freestanding GaN substrates. Lower aluminum content in the DB RTD active layer and minimization of dislocations and polarization fields enabled a more reliable and reproducible NDR behaviour at room temperature. [reprint (PDF)]
15.	Ultra-broadband quantum cascade laser, tunable over 760 cm−1, with balanced gain N. Bandyopadhyay, M. Chen, S. Sengupta, S. Slivken, and M. Razeghi Opt. Express 23, 21159-21164 -- August 10, 2015 ...[Visit Journal] A heterogeneous quantum cascade laser, consisting of multiple stacks of discrete wavelength quantum cascade stages, emitting in 5.9-10.9 µm, wavelength range is reported. The broadband characteristics are demonstrated with a distributed-feedback laser array, emitting at fixed frequencies at room temperature, covering an emission range of ~760 cm⁻¹, which is ~59% relative to the center frequency. By appropriate choice of a strained AlInAs/GaInAs material system, quantum cascade stage design and spatial arrangement of stages, the distributed-feedback array has been engineered to exhibit a flat threshold current density across the demonstrated range. [reprint (PDF)]
15.	High-power λ ~ 9.5 µm quantum-cascade lasers operating above room temperature in continuous-wave mode J.S. Yu, S. Slivken, A. Evans, S.R. Darvish, J. Nguyen, and M. Razeghi Applied Physics Letters, 88 (9)-- February 27, 2006 ...[Visit Journal] We report high-power continuous-wave (cw) operation of λ~9.5 μm quantum-cascade lasers to a temperature of 318 K. A high-reflectivity-coated 19-μm-wide and 3-mm-long device exhibits cw output powers as high as 150 mW at 288 K and still 22 mW at 318 K. In cw operation at 298 K, a threshold current density of 1.57 kA/cm², a slope efficiency of 391 mW/A, and a maximum wall-plug efficiency of 0.71% are obtained. [reprint (PDF)]
15.	Ga2O3/(Al)GaN Heterostructures for Next Generation Power Electronics Manijeh Razeghi, N. Shrestha, V. E. Sandana, D. J. Rogers, F. H. Teherani physica status solidi (b), 2026; 263:e70213 Gallium oxide (Ga2O3) is an emerging semiconductor for high-power electronics, but its low thermal conductivity, lack of viable p-type doping, and limited carrier mobility restrict device performance and prevent high-speed applications. This work presents a novel strategy to simultaneously mitigate the thermal and transport limitations of Ga2O3 through heterojunctions with III-nitride materials. Owing to their higher thermal conductivity and strong polarization fields, III-nitrides can enhance heat dissipation and enable high-density two-dimensional electron gases (2DEGs) at the heterointerface, improving switching speed. The role of spontaneous and piezoelectric polarization in 2DEG formation is systematically examined. It is shown that Al-polar AlN/β-Ga2O3 heterojunctions do not support 2DEG formation due to hole accumulation at the interface, whereas N-polar AlN/β-Ga2O3 heterostructures are identified as promising candidates for high 2DEG densities. The band alignment of the AlN/β-Ga2O3 interface is also investigated. Additionally, κ-Ga2O3, recently identified as ferroelectric with strong polarization, is explored in κ-Ga2O3/AlGaN heterostructures. Using epitaxial layer and strain engineering, electron mobilities up to 691 cm2 V−1 s −1 at 77 K were achieved in MOCVD-grown κ-Ga2O3/N-polar AlGaN/AlN heterostructures. These results highlight the potential of III-nitride/Ga2O3 heterostructures for high-power and radiofrequency device applications with enhanced performance and efficiency. [reprint (PDF)]
15.	Photoconductance measurements on InTlSb/InSb/GaAs grown by low-pressure metalorganic chemical vapor deposition P.T. Staveteig, Y.H. Choi, G. Labeyrie, E. Bigan, and M. Razeghi Applied Physics Letters 64 (4)-- January 24, 1994 ...[Visit Journal] We report infrared photoconductors based on InTlSb/InSb grown by low‐pressure metalorganic chemical vapor deposition on semi-insulating GaAs substrates. The photoresponse spectrum extends up to 8 μm at 77 K. The absolute magnitude of the photoresponse is measured as a function of bias. The specific detectivity is estimated to be 3×10⁸ Hz^½·cm·W^-1 at 7 μm wavelength. [reprint (PDF)]
15.	Concentration gradient at an InP/GaAs interface determined by Auger analysis on a chemical bevel J. Cazaux; P. Etienne; M. Razeghi J. Cazaux, P. Etienne, M. Razeghi; Concentration gradient at an InP/GaAs interface determined by Auger analysis on a chemical bevel. J. Appl. Phys. 15 May 1986; 59 (10): 3598–3601-- June 15, 1986 ...[Visit Journal] Experimental results of Auger profiles obtained on a chemical bevel of an InP/GaAs structure are reported. A theoretical procedure is established to convert the intensity profile into concentration profiles. It is applied to evaluate the concentration distribution of each species–Ga, In, As, P–independently of each others with a precision of ±5%. It is verified that the composition of the interface is GaxIn1−xAsyP1−y (0≤x, y≤1). Owing to differences between the atomic diffusions of III‐ and V‐type elements, the transition region can be subdivided into three regions having the following compositions: (i) GaAsyP1−y with 0.87≤y≤1; (ii) GaxIn1−xAsyP1−y with 0≤y≤0.87 and 0.24≤x<1; (iii) PGaxIn1−x with x<0.24. The width of each region is also indicated. [reprint (PDF)]

Page 11 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)