Center for Quantum Devices - Most Downloaded Journal Articles

Page 10 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)

16.	High Power Quantum Cascade Lasers (QCLs) Grown by GasMBE M. Razeghi and S. Slivken SPIE Proceedings, International Conference on Solid State Crystals (ICSSC), Zakopane, Poland, -- October 14, 2002 ...[Visit Journal] This paper is a brief summary of the technological development and state-of-the-art performance of quantum cascade lasers produced at the Centre for Quantum Devices. Laser design will be discussed, as well as experimental details of device fabrication. Recent work has focused on the development of high peak and average power QCLs emitting at room temperature and above. Scaling of the output is demonstrated by increasing the number of emitting regions in the waveguide core. At λ = 9 µm, over 7 W of peak power has been demonstrated at room temperature for a single diode, with an average power of 300 mW at 6% duty cycle. At shorter wavelengths, laser development includes the use of highly strain-balanced heterostructures in order to maintain a high conduction band offset and minimize leakage current. At λ = 6 µm, utilizing a high reflective coating and epilayer-down mounting of the laser, we have demonstrated 225 mW of average power from a single facet at room temperature. Lastly, these results are put in perspective of other reported results and possible future directions are discussed. [reprint (PDF)]
16.	Room Temperature Operation of InTlSb Infrared Photodetectors on GaAs J.D. Kim, E. Michel, S. Park, J. Xu, S. Javadpour and M. Razeghi Applied Physics Letters 69 (3)-- August 15, 1996 ...[Visit Journal] Long-wavelength InTlSb photodetectors operating at room temperature are reported. The photo- detectors were grown on (100) semi-insulating GaAs substrates by low-pressure metalorganic chemical vapor deposition. Photoresponse of InTlSb photodetectors is observed up to 11 µm at room temperature. The maximum responsivity of an In_0.96Tl_0.04Sb photodetector is about 6.64 V/W at 77 K, corresponding to a detectivity of about 7.64 × 10⁸ cm·Hz^½/W. The carrier lifetime in InTlSb photodetectors derived from the stationary photoconductivity is 10–50 ns at 77 K. [reprint (PDF)]
16.	III-nitride based avalanche photo detectors R. McClintock, E. Cicek, Z. Vashaei, C. Bayram, M. Razeghi and M. Ulmer Proceedings, Vol. 7780, p. 77801B, SPIE Optics and Photonics Symposium, Conference on Detectors and Imaging Devices: Infrared, Focal Plane and Single Photon, San Diego, CA -- August 4, 2010 ...[Visit Journal] Research into III-Nitride based avalanche photodiodes (APDs) is motivated by the need for high sensitivity ultraviolet (UV) detectors in numerous civilian and military applications. By designing III-Nitride photodetectors that utilize low-noise impact ionization high internal gain can be realized-GaN APDs operating in Geiger mode can achieve gains exceeding 1×10⁷. Thus with careful design, it becomes possible to count photons at the single photon level. In this paper we review the current state of the art in III-Nitride visible-blind APDs and discuss the critical design choices necessary to achieve high performance Geiger mode devices. Other major technical issues associated with the realization of visible-blind Geiger mode APDs are also discussed in detail and future prospects for improving upon the performance of these devices are outlined. The photon detection efficiency, dark count rate, and spectral response of or most recent Geiger-mode GaN APDs on free-standing GaN substrates are studied under low photon fluxes, with single photon detection capabilities being demonstrated. We also present our latest results regarding linear mode gain uniformity: the study of gain uniformity helps reveal the spatial origins of gain so that we can better understand the role of defects. [reprint (PDF)]
16.	Novel Method for Reclaim/Reuse of Bulk GaN Substrates using Sacrifical ZnO Release Layers A. Rajan, S. Sundaram, Y. El Gmili, P. L. Voss, K. Pantzas, T. Moudakir, A. Ougazzaden, D. J. Rogers, F. Hosseini Teherani, V. E. Sandana, P. Bove, K. Prior, R. McClintock & M. Razeghi Proc. SPIE 8987, Oxide-based Materials and Devices V, 898719-- April 2, 2014 ...[Visit Journal] Free-standing (0002)-oriented GaN substrates (f = 2”) were coated with 200 nm of ZnO and used as templates for the growth of GaN thin films. SEM and AFM revealed that such GaN layers had a relatively homogenous surface morphology with an RMS roughness (5 μm x 5 μm) of less than 4nm. XRD studies revealed strained ZnO growth on the GaN substrate and the reproduction of the substrate rocking curve for the GaN overlayers after only a hundred nm of growth, thus indicating that the GaN films had superior crystallographic quality compared to those grown on sapphire or ZnO/sapphire substrates. Quarter-wafer areas of GaN were removed from the GaN substrate (by selective chemical etching away of the ZnO interlayer). The expensive GaN substrates were then reclaimed/reused (without the need for polishing) for a second cycle of ZnO and GaN growth, which gave similar XRD, SEM, CL and AFM results to the first cycle. [reprint (PDF)]
16.	High Power Mid-Infrared Quantum Cascade Lasers Grown on Si Steven Slivken, Nirajman Shrestha, and Manijeh Razeghi Photonics, vol. 9, 626 ...[Visit Journal] This article details the demonstration of a strain-balanced, InP-based mid-infrared quantum cascade laser structure that is grown directly on a Si substrate. This is facilitated by the creation of a metamorphic buffer layer that is used to convert from the lattice constant of Si (0.543 nm) to that of InP (0.587 nm). The laser geometry utilizes two top contacts in order to be compatible with future large-scale integration. Unlike previous reports, this device is capable of room temperature operation with up to 1.6 W of peak power. The emission wavelength at 293 K is 4.82 um, and the device operates in the fundamental transverse mode. [reprint (PDF)]
16.	Quantum Hall liquid-to-insulator transition in In_1-xGa_xAs/InP heterostructures W. Pan, D. Shahar, D.C. Tsui, H.P. Wei, and M. Razeghi Physical Review B 55 (23)-- June 15, 1997 ...[Visit Journal] We report a temperature- and current-scaling study of the quantum Hall liquid-to-insulator transition in an In_1-xGa_xAs/InP heterostructure. When the magnetic field is at the critical field B_c, ρ_xx=0.86h/e². Furthermore, the transport near B_c scales as \|B- Bc\|T^-κ with κ=0.45±0.05, and as \|B- Bc\|I^-b with b=0.23±0.05. The latter can be due to phonon emission in a dirty piezoelectric medium, or can be the consequence of critical behavior near B_c, within which z=1.0±0.1 and ν=2.1±0.3 are obtained from our data. [reprint (PDF)]
16.	Uncooled InAs-GaSb type-II infrared detectors grown on GaAs substrates for the 8-12-μm atmospheric window H. Mohseni, J. Wojkowski, M. Razeghi, G. Brown, and W. Mitchel IEEE J Quantum Elect 35, 1041–1044 (1999)-- July 1, 1999 ...[Visit Journal] We report on the growth and characterization of type-II infrared detectors with an InAs-GaSb superlattice active layer for the 8-12-mu m atmospheric window at 300 K, The material was grown by molecular beam epitaxy on semi-insulating GaAs substrates. Photoconductive detectors fabricated from the superlattices showed 80% cutoff at about 12 mu m at room temperature. The responsivity of the device is about 2 mA/W with a 1-V bias (E = 5 V/cm) and the maximum measured detectivity of the device is 1.3 x 10(8) cm.Hz(1/2)/W at 11 mu m at room temperature. The detector shows very weak temperature sensitivity. Also, the extracted effective carrier lifetime, tau = 26 ns, is an order of magnitude longer than the carrier lifetime in HgCdTe with similar bandgap and carrier concentration. [reprint (PDF)]
16.	Widely Tunable, Single-Mode, High-Power Quantum Cascade Lasers M. Razeghi, B. Gokden, S. Tsao, A. Haddadi, N. Bandyopadhyay, and S. Slivken SPIE Proceedings, Intergreated Photonics: Materials, Devices and Applications, SPIE Microtechnologies Symposium, Prague, Czech Republic, April 18-20, 2011, Vol. 8069, p. 806905-1-- May 31, 2011 ...[Visit Journal] We demonstrate widely tunable high power distributed feedback quantum cascade laser array chips that span 190 nm and 200 nm from 4.4 um to 4.59 um and 4.5 um to 4.7 um respectively. The lasers emit single mode with a very narrow linewidth and side mode suppression ratio of 25 dB. Under pulsed operation power outputs up to 1.85 W was obtained from arrays with 3 mm cavity length and up to 0.95 W from arrays with 2 mm cavity length at room temperature. Continuous wave operation was also observed from both chips with 2 mm and 3 mm long cavity arrays up to 150 mW. The cleaved size of the array chip with 3 mm long cavities was around 4 mm x 5 mm and does not require sensitive external optical components to achieve wide tunability. With their small size and high portability, monolithically integrated DFB QCL Arrays are prominent candidates of widely tunable, compact, efficient and high power sources of mid-infrared radiation for gas sensing. [reprint (PDF)]
16.	Thermal Conductivity of InAs/GaSb Type II Superlattice C. Zhou, B.M. Nguyen, M. Razeghi and M. Grayson Journal of Electronic Materials, Vol. 41, No. 9, p. 2322-2325-- August 1, 2012 ...[Visit Journal] The cross-plane thermal conductivity of a type II InAs/GaSb superlattice(T2SL) is measured from 13 K to 300 K using the 3x method. Thermal conductivity is reduced by up to two orders of magnitude relative to the GaSb bulk substrate. The low thermal conductivity of around 1 W/m K to 8 W/m K may serve as an advantage for thermoelectric applications at low temperatures, while presenting a challenge for T2SL interband cascade lasers and highpower photodiodes. We describe a power-law approximation to model nonlinearities in the thermal conductivity, resulting in increased or decreased peak temperature for negative or positive exponents, respectively. [reprint (PDF)]
16.	Characteristics of high quality p-type Al_xGa_1-xN/GaN superlattices A. Yasan, R. McClintock, S.R. Darvish, Z. Lin, K. Mi, P. Kung, and M. Razeghi Applied Physics Letters 80 (12)-- March 18, 2002 ...[Visit Journal] Very-high-quality p-type Al_xGa_1–xN/GaN superlattices have been grown by low-pressure metalorganic vapor-phase epitaxy through optimization of Mg flow and the period of the superlattice. For the superlattice with x = 26%, the hole concentration reaches a high value of 4.2×10¹⁸ cm^–3 with a resistivity as low as 0.19 Ω · cm by Hall measurement. Measurements confirm that superlattices with a larger period and higher Al composition have higher hole concentration and lower resistivity, as predicted by theory. [reprint (PDF)]
16.	Very High Average Power at Room Temperature from λ ~ 5.9 μm Quantum Cascade Lasers J.S. Yu, S. Slivken, A. Evans, J. David and M. Razeghi Applied Physics Letters, 82 (20)-- May 19, 2003 ...[Visit Journal] We report a very high average output power at room temperature for quantum-cascade lasers emitting at λ ~ 5.9 µm. For high-reflectivity-coated 2-mm-long cavities, a low threshold current density of 1.7 kA/cm² was obtained at room temperature. From 300 to 400 K, the characteristic temperature (T0) was 198 K. A maximum average output power of 0.67 W was achieved. In addition, 0.56 W average output power was observed at a duty cycle of 56%. [reprint (PDF)]
16.	1.2–1.6 μm GaxIn1−xAsyP1−y-InP DH lasers grown by LPMOCVD M. Razeghi, B. de Crémoux, J.P. Duchemin M. Razeghi, B. de Crémoux, J.P. Duchemin, 1.2–1.6 μm GaxIn1−xAsyP1−y-InP DH lasers grown by LPMOCVD, Journal of Crystal Growth, Volume 68, Issue 1, 1984, Pages 389-397,-- September 1, 1984 ...[Visit Journal] Room temperature pulse operation and continuous wave (CW) operation in the 1.2–1.6 μm region have been achieved in GaInAsP-InP DH lasers fabricated on material grown by LPMOCVD. Threshold currents density as low as 430 A/cm2 (cavity length of 950 μm) have been measured for devices emitting at 1.3 μm. Threshold current densities of 1060 A/cm2 (cavity length of 400 μm) have been obtained for devices emitting at 1.55 μm, with active layer thicknesses of 0.22 μm. Values of T0 between 60 and 70 K have been obtained. Fundamental transverse mode oscillation has been achieved (for CW operation) up to an output power of 10 mW. The preliminary results on the aging test are most encouraging and demonstrate that the LPMOCVD lasers emitting at 1.2–1.6 μm have comparable degradation rates to those of LPE lasers suggesting the LPMOCVD technique is promising for large scale production of laser diodes. [reprint (PDF)]
16.	Gain-length scaling in quantum dot/quantum well infrared photodetectors T. Yamanaka, B. Movaghar, S. Tsao, S. Kuboya, A. Myzaferi and M. Razeghi Applied Physics Letters, Vol. 95, No. 9-- August 31, 2009 ...[Visit Journal] The gain in quantum dot/quantum well infrared photodetectors is investigated. The scaling of the gain with device length has been analyzed, and the behavior agrees with the previously proposed model. We conclude that we understand the gain in the low bias region, but in the high field region, discrepancies remain. An extension of the gain model is presented to cover the very high electric field region. The high field data are compared to the extended model and discussed. [reprint (PDF)]
16.	Core-shell GaN-ZnO Moth-eye Nanostructure Arrays Grown on a-SiO₂/Si (111) as a basis for Improved InGaN-based Photovoltaics and LEDs D.J. Rogers, V.E. Sandana, S. Gautier, T. Moudakir, M. Abid, A. Ougazzaden, F. Hosseini Teherani, P. Bove, M. Molinari, M. Troyon, M. Peres, Manuel J. Soares, A.J. Neves, T. Monteiro, D. McGrouther, J.N. Chapman, H.-J. Drouhin, R. McClintock, M. Razeghi Photonics and Nanostructures - Fundamentals and Applications, Volume 15, Pages 53-58-- March 30, 2015 ...[Visit Journal] Self-forming, vertically-aligned, ZnO moth-eye-like nanoarrays were grown by catalyst-free pulsed laser deposition on a-SiO₂/Si (111) substrates. X-Ray Diffraction (XRD) and Cathodoluminescence (CL) studies indicated that nanostructures were highly c-axis oriented wurtzite ZnO with strong near band edge emission. The nanostructures were used as templates for the growth of non-polar GaN by metal organic vapor phase epitaxy. XRD, scanning electron microscopy, energy dispersive X-ray microanalysis and CL revealed ZnO encapsulated with GaN, without evidence of ZnO back-etching. XRD showed compressive epitaxial strain in the GaN, which is conducive to stabilization of the higher indium contents required for more efficient green light emitting diode (LED) and photovoltaic (PV) operation. Angular-dependent specular reflection measurements showed a relative reflectance of less than 1% over the wavelength range of 400–720 nm at all angles up to 60°. The superior black-body performance of this moth-eye-like structure would boost LED light extraction and PV anti-reflection performance compared with existing planar or nanowire LED and PV morphologies. The enhancement in core conductivity, provided by the ZnO, would also improve current distribution and increase the effective junction area compared with nanowire devices based solely on GaN. [reprint (PDF)]
16.	TEG IN LP-MO CVD Ga 0 4 7 ln 0 S3 As-lnP SUPERLATTICE M. RAZEGHIM. A. POISSONJ. P. LARIVAINB. de CREMOUXJ. P. DUCHEMIN ELECTRONICS LETTERs, 1982 ,Vol. 18-- April 15, 1982 ...[Visit Journal] We report the first successful growth of Ga o .4. 7 In 0 . J3 As-InPsuperlattice by the low-pressure metalorganic chemicalvapour deposition technique, and evidence for TEG proper-ties in these structures. [reprint (PDF)]
16.	Recent performance records for mid-IR quantum cascade lasers M. Razeghi; Y. Bai; S. Slivken; S. Kuboya; S.R. Darvish Terahertz and Mid Infrared Radiation: Basic Research and Practical Applications, 2009. TERA-MIR International Workshop [5379656], (2009) -- November 9, 2009 ...[Visit Journal] The wall plug efficiency of the mid-infrared quantum cascade laser in room temperature continuous wave operation is brought to 17%. Peak output power from a broad area (400 μm x 3 mm) device gives 120 W output power in pulsed mode operation at room temperature. Using a single-well-injector design, specifically made for low temperature operation, a record wall plug efficiency of 53% is demonstrated at 40 K. [reprint (PDF)]
16.	High power, low divergent, substrate emitting quantum cascade ring laser in continuous wave operation D. H. Wu and M. Razeghi APL Materials 5, 035505-- March 21, 2017 ...[Visit Journal] We demonstrate a surface grating coupled substrate emitting quantum cascade ring laser with high power room temperature continuous wave operation at 4.64 μm μm . A second order surface metal/semiconductor distributed-feedback grating is used for in-plane feedback and vertical out-coupling. A device with 400 μm μm radius ring cavity exhibits an output power of 202 mW in room temperature continuous wave operation. Single mode operation with a side mode suppression ratio of 25 dB is obtained along with a good linear tuning with temperature. The far field measurement exhibits a low divergent concentric ring beam pattern with a lobe separation of ∼0.34°, which indicates that the device operates in fundamental mode (n = 1). [reprint (PDF)]
16.	Effect of contact doping on superlattice-based minority carrier unipolar detectors B.M. Nguyen, G. Chen, A.M. Hoang, S. Abdollahi Pour, S. Bogdanov, and M. Razeghi Applied Physics Letters, Vol. 99, No. 3, p. 033501-1-- July 18, 2011 ...[Visit Journal] We report the influence of the contact doping profile on the performance of superlattice-based minority carrier unipolar devices for mid-wave infrared detection. Unlike in a photodiode, the space charge in the p-contact of a pMp unipolar device is formed with accumulated mobile carriers, resulting in higher dark current in the device with highly doped p-contact. By reducing the doping concentration in the contact layer, the dark current is decreased by one order of magnitude. At 150 K, 4.9 μm cut-off devices exhibit a dark current of 2 × 10⁻⁵A/cm² and a quantum efficiency of 44%. The resulting specific detectivity is 6.2 × 10¹¹ cm·Hz^1/2/W at 150 K and exceeds 1.9 × 10¹⁴ cm·Hz^1/2/W at 77 K. [reprint (PDF)]
16.	EPR Study of Gd around the Ferroelastic Transition Point of Pb3 (PO4)2 M. RAZEGHI and B. HOULIER M. RAZEGHI et al., phys. stat. sol. (b) 89, K135 (1978) -- October 1, 1978 ...[Visit Journal][reprint (PDF)]
16.	High operating temperature MWIR photon detectors based on Type II InAs/GaSb superlattice M. Razeghi, S. Abdollahi Pour, E.K. Huang, G. Chen, A. Haddadi and B.M. Nguyen SPIE Proceedings, Infrared Technology and Applications XXXVII, Orlando, FL, Vol. 8012, p. 80122Q-1-- April 26, 2011 ...[Visit Journal] Recent efforts have been paid to elevate the operating temperature of Type II superlattice Mid Infrared photon detectors. Using M-structure superlattice, novel device architectures have been developed, resulting in significant improvement of the device performances. In this paper, we will compare different photodetector architectures and discuss the optimization scheme which leads to almost one order of magnitude of improvement to the electrical performance. At 150K, single element detectors exhibit a quantum efficiency above 50%, and a specific detectivity of 1.05x10(12) cm.Hz(1/2)/W. BLIP operation with a 300K background and 2π FOV can be reached with an operating temperature up to 180K. High quality focal plane arrays were demonstrated with a noise equivalent temperature difference (NEDT) of 11mK up to 120K. Human body imaging is achieved at 150K with NEDT of 150mK. [reprint (PDF)]
16.	High‐purity GaAs layers grown by low‐pressure metalorganic chemical vapor deposition M. Razeghi; F. Omnes; J. Nagle; M. Defour; O. Acher; P. Bove Appl. Phys. Lett. 55, 1677–1679 (1989)-- October 16, 1989 ...[Visit Journal] We report electrical and optical properties of very high purity GaAs epilayers grown by low‐pressure metalorganic chemical vapor deposition using AsH3 and triethylgallium as As and Ga sources. An electron mobility of 335 000 cm2/V s at 38 K has been measured for a 12‐μ‐thick layer. [reprint (PDF)]
16.	High Detectivity InGaAs/InGaP Quantum-Dot Infrared Photodetectors Grown by Low Pressure Metalorganic Chemical Vapor Deposition J. Jiang, S. Tsao, T. O'Sullivan, W. Zhang, H. Lim, T. Sills, K. Mi, M. Razeghi, G.J. Brown, and M.Z. Tidrow Virtual Journal of Nanoscale Science and Technology 9 (12)-- March 29, 2004 ...[Visit Journal][reprint (PDF)]
16.	Beam Steering in High-Power CW Quantum Cascade Lasers W.W. Bewley, J.R. Lindle, C.S. Kim, I. Vurgaftman, J.R. Meyer, A.J. Evans, J.S. Yu, S. Slivken, and M. Razeghi IEEE Journal of Quantum Electronics, 41 (6)-- June 1, 2005 ...[Visit Journal] We report the light-current (L-I), spectral, and far-field characteristics of quantum cascade lasers (QCLs) with seven different wavelengths in the λ=4.3 to 6.3 μm range. In continuous-wave (CW) mode, the narrow-stripe (≈13 μm) epitaxial- side-up devices operated at temperatures up to 340 K, while at 295 K the CW output power was as high as 640 mW with a wallplug efficiency of 4.5%. All devices with λ≥4.7 μm achieved room-temperature CW operation, and at T=200 K several produced powers exceeding 1 W with ≈10% wallplug efficiency. The data indicated both spectral and spatial instabilities of the optical modes. For example, minor variations of the current often produced nonmonotonic hopping between spectra with envelopes as narrow as 5-10 nm or as broad as 200-250 nm. Bistable beam steering, by far-field angles of up to ±12° from the facet normal, also occurred, although even in extreme cases the beam quality never became worse than twice the diffraction limit. The observed steering is consistent with a theory for interference and beating between the two lowest order lateral modes. We also describe simulations of a wide-stripe photonic-crystal distributed-feedback QCL, which based on the current material quality is projected to emit multiple watts of CW power into a single-mode beam at T=200 K. [reprint (PDF)]
16.	High Performance InAs/InAsSb Type-II Superlattice Mid-Wavelength Infrared Photodetectors with Double Barrier Donghai Wu, Jiakai Li, Arash Dehzangi, Manijeh Razeghi Infrared Physics &Technology 103439-- July 18, 2020 ...[Visit Journal] By introducing a double barrier design, a high performance InAs/InAsSb type-II superlattice mid-wavelength infrared photodetector has been demonstrated. The photodetector exhibits a cut-off wavelength of ~4.50 µm at 150 K. At 150 K and −120 mV applied bias, the photodetector exhibits a dark current density of 1.21 × 10−5 A/cm2, a quantum efficiency of 45% at peak responsivity (~3.95 µm), and a specific detectivity of 6.9 × 1011 cm·Hz1/2/W. The photodetector shows background-limited operating temperature up to 160 K. [reprint (PDF)]
16.	High speed type-II superlattice based photodetectors transferred on sapphire Arash Dehzangi, Ryan McClintock, Donghai Wu, Jiakai Li, Stephen Johnson, Emily Dial and Manijeh Razeghi Applied Physics Express, Volume 12, Number 11-- October 3, 2019 ...[Visit Journal] We report the substrate transfer of InAs/GaSb/AlSb based type-II superlattice (T2SL) e-SWIR photodetector from native GaSb substrates to low loss sapphire substrate in order to enhance the frequency response of the device. We have demonstrated the damage-free transfer of T2SL-based thin-films to sapphire substrate using top–down processing and a chemical epilayer release technique. After transfer the −3 dB cut-off frequency increased from 6.4 GHz to 17.2 GHz, for 8 μm diameter circular mesas under -15 V applied bias. We also investigated the cut-off frequency verses applied bias and lateral scaling to assess the limitations for even higher frequency performance. Direct Link [reprint (PDF)]

Page 10 of 31: Prev << 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 >> Next (771 Items)